UnOfficial EVGA X58 Classified Owners Thread

[2slick4u]

Mother Board ( EVGA X58 Classified E-760 )
Drivers ( ? )
Bios ( 49 )
CPU ( 920 D0 )
CPU Cooler ( Heat Killer 3.0 )
Memory ( Patriot Viper Extreme 3x2gb 1600mhz 8 8 8 24 1t )
PSU ( Thermaltake Black Widow 850W )
GPU ( Ati 5870 )
Drivers ( 10.2 )
Operating System ( Windows 7 64 Pro )
Frequency Control
CPU Clock Ratio ( 20X )
CPU Host Frequency (Mhz) ( 191 )
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) Auto
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )
Memory Feature
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 1520Mhz / 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( auto )
tCL Setting ( 8 )
tRCD Setting ( 8 )
tRP Setting ( 8 )
tRAS Setting ( 24 )
tRFC Setting ( 74 )
Command Rate ( 1t )
Voltage Control
EVGA VDroop Control ( With VDroop )
CPU VCore ( 1.2 )
CPU VTT Voltage ( +75 )
CPU PLL VCore ( 1.5 )
**IOH PLL VCore ( 1.5 )
DIMM Voltage ( 1.65 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( auto )
IOH VCore ( Auto )
IOH/ICH I/O Voltage ( Auto )
**VTT PWM Frequency ( 250 KHZ )
**CPU PWM Frequency ( 800 KHZ )
**CPU Impedance ( less )
**QPI Signal Compensation ( Less )
ICH VCore ( Auto )
CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Disabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s )
OC Recovery ( Disabled )
Turbo Performance ( Disabled )

So far i got it stable at this setting
Tell me if there anything u see wrong please

[davidm71]

Mother Board ( EVGA X58 Classified E-760 )
Drivers ( ? )
Bios ( 49 )
CPU ( 920 D0 )
CPU Cooler ( Heat Killer 3.0 )
Memory ( Patriot Viper Extreme 3x2gb 1600mhz 8 8 8 24 1t )
PSU ( Thermaltake Black Widow 850W )
GPU ( Ati 5870 )
Drivers ( 10.2 )
Operating System ( Windows 7 64 Pro )
Frequency Control
CPU Clock Ratio ( 20X )
CPU Host Frequency (Mhz) ( 191 )
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) Auto
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )
Memory Feature
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 1520Mhz / 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( auto )
tCL Setting ( 8 )
tRCD Setting ( 8 )
tRP Setting ( 8 )
tRAS Setting ( 24 )
tRFC Setting ( 74 )
Command Rate ( 1t )
Voltage Control
EVGA VDroop Control ( With VDroop )
CPU VCore ( 1.2 )
CPU VTT Voltage ( +75 )
CPU PLL VCore ( 1.5 )
**IOH PLL VCore ( 1.5 )
DIMM Voltage ( 1.65 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( auto )
IOH VCore ( Auto )
IOH/ICH I/O Voltage ( Auto )
**VTT PWM Frequency ( 250 KHZ )
**CPU PWM Frequency ( 800 KHZ )
**CPU Impedance ( less )
**QPI Signal Compensation ( Less )
ICH VCore ( Auto )
CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Disabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s )
OC Recovery ( Disabled )
Turbo Performance ( Disabled )

So far i got it stable at this setting
Tell me if there anything u see wrong please

I don't think you have enough vcore. Try 1.3 instead. Also does the memory divider go lower? Maybe your memory frequency is the problem. Try like 21X multi (with Turbo) and 181 bclk. Then your memory will be around 1455 with less strain on the memory controller.

[ZL1Killa]

Why is it that my FSB/BCLK is always at a x.5 interval instead of what I set it to?
For instance, I set my FSB to 210, well in CPUZ it shows 209.5... and when I right click my computer and properties it equates to the same thing (math works out)

[zalbard]

Incorrect reading. This is normal.

[zalbard]

Bios 49 is out.

[SAE]

This bios has been out for several days now, huh?

[Salamndar]

Damn it!!

I have been trying hard to reach 4.5GHz with my corei7 950 but the highest I could get is 4.3 !!

I even reached v. core @ 1.5 but no luck even stabelize at 4.4

My X-Corei7 920 could reach 4.4 with voltage of 1.46 !!!!!!

[zalbard]

This bios has been out for several days now, huh?

No one's posted about it here before, and I don't really read EVGA forums...

[=[PULSAR]=]

new bios supposedly has fixed bootup bclk issues? I'll have to test that soon.

[The_Game]

There are no bootup problems since S61A.

[lowfat]

Does everyone elses Classified shut off completely for a few seconds every time you restart your computer? I can remember a time when mine didn't (maybe it was @ default clocks). This shut off adds a good 10-15 seconds to my reboot time.

[The_Game]

My E760 and now E762 never do that. Sometimes it takes long time to POST after a few hours power down but it starts with overclocked settings not at default like some GB boards. If I dont change anything in BIOS no shutting down when restart .

[zalbard]

Does everyone elses Classified shut off completely for a few seconds every time you restart your computer? I can remember a time when mine didn't (maybe it was @ default clocks). This shut off adds a good 10-15 seconds to my reboot time.

Nope, everything's smooth and bug free here, no VT power cycles or anything people complain about...

[Salamndar]

There are no bootup problems since S61A.

Some times I get a cold boot issue with BIOS 44 and 49.

[cstkl1]

eh whats that new option in the bios for??

turbo performance??

[cstkl1]

hmm new bios interesting

rtl's are different now

second the tfaw for 1600 mch strap now is 24.. when it should be 30

seems to be a bit more stable on the voltages according to my dmm.

[SAE]

eh whats that new option in the bios for??

turbo performance??

Hey mate,

that's an option to speed up westmere's L3 caches.

[cstkl1]

Hey mate,

that's an option to speed up westmere's L3 caches.

oh ok.. that explains why its disabled

hm they should put a warning for that bios that previous templates wont work since all the voltage tables are different.

that would solve 75 percent of the issue on evga forum

so uve gone to hexacore??

[SAE]

Nope, not yet. I think I'll wait for the better steppings

[cstkl1]

Nope, not yet. I think I'll wait for the better steppings

yeah lol
as long they run 2100mhz Cl7.. all good

[ZL1Killa]

how is that newest bios? any reason to jump from s61 to this one?

[zalbard]

how is that newest bios? any reason to jump from s61 to this one?

I'd say no... Unless you have some kind of boot up cycle issues with VT.

[justin.kerr]

49 has been good for me, max 24 hour prime 95 RAM speed was 2130Mhz, with new BIOS 2150Mhz... solid BIOS so far on the 3 classifieds I have

[overclockers]

Hi
Please help me!!
Capacitor& MOSFETshown in the image are very hot
Is this normal?Motherboard has a problem?
Thanks

[overclockers]

Here seem not someone give me the answer
I just wanted to know your motherboard has this problem or not(MOSFET and cap tempe very High, up to 65c but NB Temp is 35c)
However, my issue was solved with the help Evga forum