BCLK 222
BCLK 222
sorry my english its not good
Anuaja could you plz share your settings having trouble getting past 214Bclk.
Intel I7 980x|Evga Classified 760 | Corsair Domiator Gt | Msi Gtx480| Cpuz
OMG Last night I dreamed that I bought a swiftech cooling system for my RIIE!! Maybe I should do that!!
I want to run a W3540, however there seems to be an issue with this and the R2E.
From the Asus website, for some strange reason it seems Xeons are not supported by the R2E. According to their site, the only boards that support the W3540 are the P6T WS Professional, P6T6 WS Revolution and P6T7 WS SuperComputer.
Anyone running a Xeon have any input?
Last edited by CryptiK; 09-01-2009 at 05:48 AM.
I have a Xeon W3540 running now @default on my R2E without any problem.... What's the issue with R2E?!Originally Posted by CryptiK
Windows 7 Ultimate 64bit, SP1 Power By:
Asus Rampage IV Formula
Intel SBE 3930K
Gskill RipJaws Z 14900 (1866 DDR3) 16GB 10-11-10-24
EVGA 570 GTX SLI
SSD Samsung P830 240GB
Corsair AX850
I had a W3520 till early June and starting from BIOS 14xx it is completely supported.
So can you control uclk and mem multipliers? People were expressing problems earlier in the thread, and were very happy when 1403 beta was released which allowed full control over Xeons.
I was hoping Asus would by now have non beta BIOSes giving full support for Xeons, but their website seems to indicate that they do not.
On R2E, Yes we can!
Windows 7 Ultimate 64bit, SP1 Power By:
Asus Rampage IV Formula
Intel SBE 3930K
Gskill RipJaws Z 14900 (1866 DDR3) 16GB 10-11-10-24
EVGA 570 GTX SLI
SSD Samsung P830 240GB
Corsair AX850
Great, what BIOS are you on?
Rampage II Extreme 1504 BIOS
1. Updated configuration table of OC Station.
2. Fixed Target DRAM Frequency incorrect for DDR3-1333 with non-extreme CPU when set
DRAM Frequency to auto in BIOS setup.
3. Supported display warning message when set CPU Voltage or QPI/DRAM Core Voltage
over 1.8V in TurboV.
http://www.asus.com/product.aspx?P_I...Mih&templete=2
Windows 7 Ultimate 64bit, SP1 Power By:
Asus Rampage IV Formula
Intel SBE 3930K
Gskill RipJaws Z 14900 (1866 DDR3) 16GB 10-11-10-24
EVGA 570 GTX SLI
SSD Samsung P830 240GB
Corsair AX850
Great thanks. Glad to hear the w3540 is fully supported by this bios.
I do prefer the R2E for a 24/7 system board, I didn't want to have to choose another board due to lack of full xeon support.
I run my w3520 @ 4.34ghz 24/7 np
Rampage II Extreme 1504 BIOS
1. Updated configuration table of OC Station.
2. Fixed Target DRAM Frequency incorrect for DDR3-1333 with non-extreme CPU when set
DRAM Frequency to auto in BIOS setup.
3. Supported display warning message when set CPU Voltage or QPI/DRAM Core Voltage
over 1.8V in TurboV.
http://www.asus.com/product.aspx?P_I...Mih&templete=2
TurboV runs on W7 ?
Apple MacBook Air
Apple IPad 2
Yes, I installed it in compatabily mode (vista) and it then runs fine in Win 7.
Main Rig;
Asus Rampage II Ex, i7 920DO @ 3.64, 12 Gb Corsair Dominator DDRIII, Corsair H-70, Corsair 1 KW PSU, 2 ea EVGA 580's in SLI driving 3 Samsung 245t's at 5760 X 1200 surround, Boot drive Corsair Vertex II SSD, Programs 2 V- Raptors in RAID 0 and a WD 1 Tb RE3 for files and client data. Sound, ASUS Xonar D2X, Normal optical drives Etc. Win 7 Ult.
Yes it works perfect in W7 on my system also
| ASUS REII || i7 920 || 6GB G.Skill DDR3 16000 Perfect Storm || Sapphire"VAPOR-X" HD 4890 CF || DELL U2410 ULTRASHARP 24 || Corsair 850HX || Samsung F1 1TB x 4 || Seagate7200.12 1TB x 2 || 3 x OCZ 30GB Vertex @ Raid0 || Pioneer DVR-216D || G15V2 || MX518 | Qpad XT-R || Win 7 |
| Obsidian 800D || HK Rev. 3.0 LT || BP BF AIX58NSE || BP BF MOS AMOS II || BP BF MOS AMOS III || MCP655 + EK X-TOP Rev.2 || EK-Multioption RES 250 Rev.2 || Tygon R3603 || XSPC RX360 + Yate Loon D12SL-12 || BP Compression Fittings 1/2in. || T-Balancer/bigNG |
Did that also, didnt work last time i tried!
Tonight it did, weird
Tnx
Apple MacBook Air
Apple IPad 2
Finally got my i7 920 D0 up and running and OC'd. Got it running at 4Ghz w/ HT on at 1.28v. Ran prime 95 a little under and hour with out a hiccup but I am planning to run prime again for a full 8-12 hour test and maybe a 24 hour test.
Love this mobo... so easy to OC with so many options!
Core i7 Gaming Machine
CPU: Intel Core i7 920 D0 (Batch: 3849B310) - 4Ghz @ 1.28v HT/Turbo On
Mobo: ASUS Rampage II Extreme
RAM: Corsair Dominator DDR3-1600 6GB
GPU: 2xBFG Tech GTX 295 in SLI
PSU: Corsair HX1000w Modular
HDD1: WD VelociRaptor 300gb - OS/Apps/Games
HDD2: Seagate 1.5TB Baracuda - Storage
Cooler: Prolimatech Megahalems + 2 Enermax Magma Push/Pull
Case: Cooler Master ATCS 840 Black
Need a little help guys
My DVD burner (Samsung SH-S203D) is connected to the last port on ICH10R controller (SATA6), now it all works OK, but will only burn in PIO mode under Windows 7 RTM??
Controller is set to RAID mode as I have my non-member disk SSD on SATA1, and a RAID0 of 3 Seagate disks on SATA/2/3/4 and a caddy disk on SATA5.
I tried the burner on the JMicron port and it seems to work fine in DMA mode, but I don't want to use the JMicron controller whatsoever, one of the reasons being that it irritates me at boot up with that annoying message, but mostly because I'd just love it to work properly on the Intel controller.
Are we talking of maybe an incompatibilty between this burner and the Intel RAID controller for this drive, or is it so that on the RAII, one cant have any SATA optical device running in DMA mode when the controller is set to RAID in BIOS??
Any feedback appreciated
PS.
Tried all configuration of drivers, Intel chipset, no Intel chipset, Matrix Storage, no Matrix Storage etc. etc.
A government big enough to give you everything you want, is big enough to take away everything you have.
System Specs: CM Stacker STC-T01 | Asus Z68 V Pro Gen3 (BIOS 3202) | INTEL Core i7 2600K @ 5Ghz | Corsair 8GB DDR3 1600MHz Vengeance Blue RAM | Corsair 750W TX PSU | Geforce GTX 580 - EK-FC580 Watercooled | XSPC Drive Bay Res | XSPC Raystorm CPU Watercooled | Swiftech MCR320-QP | Swiftech MCP655 | 1 x Corsair Force GT 120Gb SSD & 3 x Seagate Barracuda 7200.12 500Gb RAID 0 | X-Fi Titanium Fatal1ty Pro | DELL U2410 (Rev A02) | Windows 7 Ultimate x64
I'm not sure whether it's related. I had some weird stuff with my burner too when coming out of sleep mode. After I plugged it into the first SATA port all problems went away. It might be worth a shot.
Guys I have some more questions:
1) What Power Temp (cpu mosfet/PWM) temps are you getting on this board under linx / prime95 load with cpu clocks of 4.0 - 4.4GHz ?
2) What BCLK can be achieved without raising PCI-E freq?
3) If PCI-E freq is raised, do the lan NIC's disappear as with other boards? If they do, at what PCI-E freq does this occur?
4) Lastly, for anyone that has used the same CPU on both a Classified 760 and the R2E, did the R2E require a higher vcore to be stable at the same clock compared to the classified? Did the R2E require more Vtt (QPI) for the same ram clock compared to the Classified?
Last edited by CryptiK; 09-02-2009 at 08:50 AM.
Ive heard of a term "saturated sata controller" it seems that you are having just that.I just have 3 SSD in Raid0 on ports 1-2-3 and my DVD on port 6 and it works perfect.Need a little help guys
My DVD burner (Samsung SH-S203D) is connected to the last port on ICH10R controller (SATA6), now it all works OK, but will only burn in PIO mode under Windows 7 RTM??
Controller is set to RAID mode as I have my non-member disk SSD on SATA1, and a RAID0 of 3 Seagate disks on SATA/2/3/4 and a caddy disk on SATA5.
I tried the burner on the JMicron port and it seems to work fine in DMA mode, but I don't want to use the JMicron controller whatsoever, one of the reasons being that it irritates me at boot up with that annoying message, but mostly because I'd just love it to work properly on the Intel controller.
Are we talking of maybe an incompatibilty between this burner and the Intel RAID controller for this drive, or is it so that on the RAII, one cant have any SATA optical device running in DMA mode when the controller is set to RAID in BIOS??
Any feedback appreciated
PS.
Tried all configuration of drivers, Intel chipset, no Intel chipset, Matrix Storage, no Matrix Storage etc. etc.
| ASUS REII || i7 920 || 6GB G.Skill DDR3 16000 Perfect Storm || Sapphire"VAPOR-X" HD 4890 CF || DELL U2410 ULTRASHARP 24 || Corsair 850HX || Samsung F1 1TB x 4 || Seagate7200.12 1TB x 2 || 3 x OCZ 30GB Vertex @ Raid0 || Pioneer DVR-216D || G15V2 || MX518 | Qpad XT-R || Win 7 |
| Obsidian 800D || HK Rev. 3.0 LT || BP BF AIX58NSE || BP BF MOS AMOS II || BP BF MOS AMOS III || MCP655 + EK X-TOP Rev.2 || EK-Multioption RES 250 Rev.2 || Tygon R3603 || XSPC RX360 + Yate Loon D12SL-12 || BP Compression Fittings 1/2in. || T-Balancer/bigNG |
On Asus ftp site there is version 1.0.41 for Vista and Win7 and obviously it works.
If I remember correctly, if you use relative Vcpu (BIOS 15xx), using Turbo V reverts it to absolute.
site is down.. ill get it when its back on .. tnx !
Last edited by AceBaran; 09-02-2009 at 08:48 AM.
Apple MacBook Air
Apple IPad 2
havent noticed any major stability difference with changing the PCI-E freq.
can do 228bclk with PCI-E on def 100Mhz.(19x228)
on higher multi 103MHz seems to be the magic number for me.
You remember where on the ftp server you found this new version?
Asus Rampage II Extreme (1504)
i7 920 @ 210x21 4.4ghz 1.37v/1.26vtt 3849A916 HT on
6GB G.Skill Trident 16000 Elpida BBSE @ 6-7-6-20 1682mhz 1.55v
GTX 295 Single PCB @ stock :<
HK 3.0 Copper, MCR320, Laing DDC 18w, XSPC Res Top: 38c Idle / 73c Load
Posting Permissions
Reply With Quote
Bookmarks