Foxconn Bloodrage-Quantum Force- -X58- -Retail-

[CCC]

final air runs for the night on this board, ill try bios g13 tommorow 'I heard its better'
and setup for subzereo

[dengyong]

My Settings are:
19x200
Vcore +60mv 1,21v with Prime
Vtt +100mv
IOH 1,12v
Dram 1600Mhz
Uncore 3200Mhz

With my old Gigabyte Extreme i need only 1,16v for 3800Mhz. QPI is 1,235v. How much Vcore do you need for 4019Mhz and VTT?

+50 vcore
+180 vtt

[inzaghi75]

+50 vcore
+180 vtt

Is your Setting 19x211?

[dengyong]

Is your Setting 19x211?

I don't use this utility to clock, only to show settings.
This is what I run 24/7

[saaya]

My Settings are:
19x200
Vcore +60mv 1,21v with Prime
Vtt +100mv
IOH 1,12v
Dram 1600Mhz
Uncore 3200Mhz

With my old Gigabyte Extreme i need only 1,16v for 3800Mhz. QPI is 1,235v. How much Vcore do you need for 4019Mhz and VTT?

how do you read voltages?
you cant really compare bios or windows meassured voltages or the voltage settings in bios even since they fluctuate and arent 100% accurate. Plus each board reads voltages differently

Sme read vtt at the pwm, some between pwm and socket and some inside the socket. the differences can be quite big just from where you read voltages. Imo the best spots to meassure voltages is as close to the parts they are powering as possible, cause thats what matters. On BloodRage the voltage pads are doing a pretty good job, especially for vtt.

the vcore and vtt settings and readings in the current bioses of BloodRage are not accurate and a bit off, we are working on adusting them now

[Touge180SX]

how do you read voltages?
you cant really compare bios or windows meassured voltages or the voltage settings in bios even since they fluctuate and arent 100% accurate. Plus each board reads voltages differently

Sme read vtt at the pwm, some between pwm and socket and some inside the socket. the differences can be quite big just from where you read voltages. Imo the best spots to meassure voltages is as close to the parts they are powering as possible, cause thats what matters. On BloodRage the voltage pads are doing a pretty good job, especially for vtt.

the vcore and vtt settings and readings in the current bioses of BloodRage are not accurate and a bit off, we are working on adusting them now

Good to have you back Saaya!

[inzaghi75]

@saaya
Do you now the Date of the New Bios?

@dengyong

It´s the same Settings but without Turbo Mode. And i don`t need so much VTT. Is this right that VTT is only for OC the Memory and the Uncore?

[Lu(ky]

Anyone know where one can buy a Bloodrage Rev 2? Still nothing at newegg..

Thanks

[CCC]

how ya know what rev board ya have got?

[tripgood]

how ya know what rev board ya have got?

As I recall, it's along the bottom edge of the pcb near the last pci-e slot but my memory fails me at times.

[SAE]

Is this right that VTT is only for OC the Memory and the Uncore?

It is improving memory stability at high mem clocks. High uncore clocks gain stability from upping vdimm.

[jooney]

My problem was that i doesnt disabled PPM
OC with EIST/C1E goes up to a BCLK from 166,above i must disable it.
Would be very nice if this with a upcoming Bios also run at high BCLK

So here is my new bloody friend

[rbuass]

The best i did on air (TR120 cooper)



i think 219 is good

[tripgood]

219 is very good. What is the batch no. of your processor?

[rbuass]

219 is very good. What is the batch no. of your processor?

3838A...i think is a good chip...but not as a b series

[SAE]

So here is my new bloody friend
...

Mate, that's a kicka$$ system! I am doing something similar, in case my board arrives this week.

[Lu(ky]

Anyone using these OCZ Platinum 6GB (3 x 2GB) 1600 (PC3 12800) CAS (7) on this board? Any problems?

[tripgood]

3838A...i think is a good chip...but not as a b series

Can you run that bclk with all 3 channels used?

[rbuass]

Can you run that bclk with all 3 channels used?

Yes i used 3 X G.Skill 1600 Pi Black and reach 219

[Touge180SX]

What VCore and VTT did you run to get the 4.5 and was it completely stable and with what temps? The reason I ask is that I can reach 220 BClock on my 920 but when I up the multi it becomes unstable.

[saaya]

My problem was that i doesnt disabled PPM
OC with EIST/C1E goes up to a BCLK from 166,above i must disable it.
Would be very nice if this with a upcoming Bios also run at high BCLK

why do you have to disable EIST and PPM? without it you wont be able to use turbo... if you want the cpu to run at full speed all the time set cpu turbo to always on

So here is my new bloody friend

wow... ...beautiful...

rbuass, very nice!
try setting vcca 1.1v higher and play with the other chipset voltages, you might be able to get some more out of it
whats the highest you can boot at?
whats the max 3d stable?

Yes i used 3 X G.Skill 1600 Pi Black and reach 219

nice!

[jooney]

Mate, that's a kicka$$ system! I am doing something similar, in case my board arrives this week.

Thanks SAE The Masterkleer in your Sig is the same im using here

why do you have to disable EIST and PPM? without it you wont be able to use turbo... if you want the cpu to run at full speed all the time set cpu turbo to always on


wow... ...beautiful...

Also thanks

Really dont know what was wrong here,but i can use it now all the time
With Turbo CPU-Z and Everest shows the 21 Multi but the i7 Turbo Tool told me around 20,7 under load.
And the VCore is totally different with 21x191,19x211 is ok.

[s002wjh]

Anyone using these OCZ Platinum 6GB (3 x 2GB) 1600 (PC3 12800) CAS (7) on this board? Any problems?

i'm using it, no problem at all. hitting 1650 with cas 7, and 1800 with cas 8 1.64v

[Lu(ky]

i'm using it, no problem at all. hitting 1650 with cas 7, and 1800 with cas 8 1.64v

Thanks for quick reply

[cheesemonkey]

I have a problem with my case, for the power led it is a 3pin pin connector. 2 wires on each end meaning the middle pin slot is empty. Where do i plug this in so it works properly because according to the manual it should be a 2 pin.