Micron D9 GMH\GKX\JKH etc club

[PolRoger]

PolRoger - It would make a lot more sense if the DFI voltage software is under-reporting the voltages, I have a hard time believing the ram or the NB for that matter would be stable at those speeds & PL. Any chance you can measure the real vdimm with a DMM please?

westsider - nice work, what voltages were used for each setting. Also your link for 32M CL3 is missing.

Cryptik- I will try... I have a DMM but I'm not sure where I would take the readings on the board?

However, I think the readings might be correct. The actual readings in the BIOS seem to match up with what is being reported in the ITE software in windows.

BTW: I've been testing my Powerchip IC Reapers... using the same 333/800 divider and similar low voltages... so far I've managed 8.5x470 DDR2-1129
with my 4GB kit of PC2-8500 at 1.95v and 8x500 DDR2-1200 with my 2GB kit of PC2-9200 at 2.0v. VTT and MCH/NB were both at default.

Here is a photo of my BIOS voltage screen for my current 8.5x470 DDR2-1129 overclock

[Saturas]

Hi guys, I'd like to do some DDR2 Benches in the next months - so I may need another Board and some Kits for 3V+ around x-mas time.

I'd just like to know if there are any special boards going extraordinary well with Micron D9GMH and D9GKX.

I actually have a DFI UT-P35-T2R , but it's not working that good with my G.Skill PC2-8000GBHZ (D9GKX) and with the Supertalent PC2-8000 (D9GKX) either.

I already had another DFI UT-P35-T2R some time ago combinated with a Crucial 2x512Mb PC2-8000 Kit and could easily run DDR2-1000 3-4-3-4 @ 2.6V through SuperPi 32M.

Now I see no chances to hit 700Mhz CPU-Z stable with the G.Skill / Supertalent - so I'd like to try another Board, because the G.Skills are pretested on 685Mhz 5-6-6-18 @ 2.53V Pi 1M .

[Ket]

My Asus P5Q Pro with 703m work fantastic with my D9 GKX, boots 1300MHz @ 2.2v.

[jaredpace]

Would it suit me fine to search for DDR2 that does high speeds like 1066mhz or greater at nice timings & low volt specs? like 1150mhz / 5 5 5 15 / 1.9v ?

Or is there a particular brand / make / model to purchase to guarantee high overclocks? I'm looking for ~600mhz or more at ~2.1v.

Which brand & model do you fellas recommend? I was looking at a 2x1GB kit of OCZ HPC Reaper PC2-9600

[WaterFlex]

jaredpace
CellShock "Red Devil"
I have 2 kits. I run 1200MHz, Pl=8 for 24/7 usage at 2,06Vdimm

[PolRoger]

jaredpace
CellShock "Red Devil"
I have 2 kits. I run 1200MHz, Pl=8 for 24/7 usage at 2,06Vdimm

WaterFlex- Those red sticks seem very nice but they don't seem to be available. I see that MemoryC has the black PC2-8000 4-4-4-12 kit.

[WaterFlex]

WaterFlex- Those red sticks seem very nice but they don't seem to be available. I see that MemoryC has the black PC2-8000 4-4-4-12 kit.

You should search for them at German shops. I'll give you few links after 10 hours, mate.

[RASTAVIPER]

238 MHz? How is that even possible? Something is very wrong mate. Should get 500 CL 4, 550+ @ 5-4-4.

Got a 240 with 2.1 in memtest.
In what voltage do you have CL4 and 500?
I am just reminding you that I have the 5-5-5 PC8000.

[CryptiK]

500 MHz (DDR2-1000) CL4 @ 2.1v totally stable. 600 MHz (DDR2-1200) CL5 @ 2.06v totally stable.

240MHz is DDR2-480MHz, that is worse than DDR1 speeds, and you would have to be underclocking the FSB to achieve that. Are we on the same page here? What is your cpu FSB set to?

[PolRoger]

PolRoger - It would make a lot more sense if the DFI voltage software is under-reporting the voltages, I have a hard time believing the ram or the NB for that matter would be stable at those speeds & PL. Any chance you can measure the real vdimm with a DMM please?

westsider - nice work, what voltages were used for each setting. Also your link for 32M CL3 is missing.

CryptiK- I posted some of my results in the "UT Banter" thread and C-N replied with this concerning dimm voltage...

"@ PolRoger forgot to mention the board overvolts the RAM slightly .05v on my DMM, also the Prime shot shows 48~56k try custom 4096 for an hour rather than small fft's that just test the CPU cache."

[Saturas]

You should search for them at German shops. I'll give you few links after 10 hours, mate.

Here's no shop still selling them .

and you would have to be underclocking the FSB to achieve that. Are we on the same page here? What is your cpu FSB set to?

As I see it he has an AMD CPU so he doesn't have the problem that ther're no clocks below FSB-setting possible .

[WaterFlex]

Here's no shop still selling them .

You`re right. There is no more Cellshocks available.
What`ve happened with the company?

[RASTAVIPER]

500 MHz (DDR2-1000) CL4 @ 2.1v totally stable. 600 MHz (DDR2-1200) CL5 @ 2.06v totally stable.

240MHz is DDR2-480MHz, that is worse than DDR1 speeds, and you would have to be underclocking the FSB to achieve that. Are we on the same page here? What is your cpu FSB set to?

As I see it he has an AMD CPU so he doesn't have the problem that ther're no clocks below FSB-setting possible .

The thing is that I tried to put a different divider to put the memory at DDR2 1000+, but the pc just couldn't boot.
So, the fsb is not a matter.

[CryptiK]

Yeah right I missed tha fact he had an AND cpu. Not sure what the issue could be then, as I have next to no experience with AMD systems (other than the old Athlon XP's etc).

[Saturas]

You`re right. There is no more Cellshocks available.
What`ve happened with the company?

It's well known that D9s aren't produced anymore so if the kits are sold out there's nothin new coming up .
The 2GB PC-8500 5-5-5-15 are available for 50€ here .. interesting price ...

All want 4GB Kits or DDR3 D9GTR now =/ .

[WaterFlex]

I want these girls JNL seems to be the best for me.

[jaredpace]

what does PL8 mean?

[Big Lar]

what does PL8 mean?

PL8 = Performance Level 8.

Larry

[BigDMadinko]

Well I've got my new Cellshock PC2-8000 4-4-4-12 RAM and so far it seems pretty good. I have to say though its not taking me much higher than the GMH AxeRam ive been using, in fact it needs more voltage for the same speeds so far. I'm using Ket's 1306m BIOS for the P5Q Pro but Ket recommends using the 703m ior 704m BIOS with GKH D9s. Does anyone have a copy of this version or a working link for it? I've been trying to get them from his megaupload sites and the links haven't been working.

[Saturas]

I want these girls JNL seems to be the best for me.

I'll start with DDR3 again when i made some personal/global (we'll see ) DDR2 records.

[radaja]

i got my PC8000 mushkin redlines 2x1 today gonna have fun this weekend (also got my maximusII formula replacement) cant wait!

[Elektrosadist]

I'm getting my first microns tomorrow. A little late but heck at least i got some after all. I'm really excited to see what they can do especially since they seem to scale so good with more voltage to get more bandwidth

i will still use my old OCZ coolers



but im gonna spray em black tomorrow and instead of the OCZ logo i will make a micron sticker and put in there.

[philbrown23]

those OCZ coolers are actually really affective

[Elektrosadist]

I no

[kimchupa]

might seem a very noob question...however
I want to get some 2g module DDR2 Micron D9 rams so I looked up in the ramlist site but I get bit confused.
since there are several which are D9 but they differ as for their revs and year
I wonder which one is a 2 gig Micron D9 module 100% if I buy them now in the market....
where can i get them? and which one is a 100% D9?

ps: where can i get the older revs of rams? any sites? if its inconvenient to post the site in the thread pls pm the the sites where I can get a 100% 2 gig D9 Modules
ps2: is the mushkin 4GB (2 x 2GB) DDR2 1000 (PC2 8000) Dual Channel Kit D9 module 100% it does not say redline but the heatsink is (in newegg)