**Official DFI LanParty UT X48-T2R(and LT) Discussion

[zanzabar]

i had messaged jimmyz about a custom one he said that it was doable but never went through with it, since i never raised the money for liquid

[Sauron_Vie]

If i set the read delay phase to enabled i got a complete nogo, on auto it works. whats the clue for read delay phase ??

Currently i am using the cellshock pc9200 sticks with D9GKX chips.

tia

[zanzabar]

If i set the read delay phase to enabled i got a complete nogo, on auto it works. whats the clue for read delay phase ??

Currently i am using the cellshock pc9200 sticks with D9GKX chips.

tia

try e-a-e-e-e/e-a-a-e-e

and u will need 1.5V+ on the NB, and u may have problems on cas5 from 1000-1150 with gkx so use 4-4-4-10 in those spaces

[Sauron_Vie]

try e-a-e-e-e/e-a-a-e-e

and u will need 1.5V+ on the NB, and u may have problems on cas5 from 1000-1150 so use 4-4-4-10 in those spaces

ok, thx mate for the hint. i will try and report...

tia

[Sauron_Vie]

try e-a-e-e-e/e-a-a-e-e

and u will need 1.5V+ on the NB, and u may have problems on cas5 from 1000-1150 with gkx so use 4-4-4-10 in those spaces

Tried your settings and it´s working fine, but can´t raise fsb against 440 cause with this "small" watercooling. hope the cascade will be ready soon.

Thx mate

for now i reached this:

[Jor3lBR]

what are the available waterblocks for the PWM?
I have been looking on some UK e-shops but I haven't found any

Recently I got a 8 pieces shipment to USA from vcore.dk (Group Buy I organized here in XSF), they got the HK Sw-16 from Watercool.de the best your money can buy for the X38, X48 or P35...(Made in Germany).

Try here: vcore.dk

[ZenEffect]

Tried your settings and it´s working fine, but can´t raise fsb against 440 cause with this "small" watercooling. hope the cascade will be ready soon.

Thx mate

for now i reached this:

now use memeset and change your tREF from 4041T to 16383T and watch what happens
since you are using only 2 gigs, you should be just fine. i find that the tREF on this board is tuned for 4+ gigs of ram...

[Sauron_Vie]

now use memeset and change your tREF from 4041T to 16383T and watch what happens
since you are using only 2 gigs, you should be just fine. i find that the tREF on this board is tuned for 4+ gigs of ram...

thks for the further hint buddy.

have changed the tref on fsb 440 and got this:




and got this now fsb 450:




thks for the great tipps


maybe i will reach the 460 but tomorrow i have to change the radiator


greets

[zanzabar]

are u realy using 1.6V on a 45nm chip, thats not a good idea

[Sauron_Vie]

saw it after the reboot and in everest. dont know why but probably i changed it by mistake with the other Voltages, but it´s already changed again to 1,35V. it was my fault.

tia

[TouGe]

now use memeset and change your tREF from 4041T to 16383T and watch what happens
since you are using only 2 gigs, you should be just fine. i find that the tREF on this board is tuned for 4+ gigs of ram...

Good call on the tREF Zen. I just started messing with this now that I've tightened every DRAM timming in the BIOS. I'm already seeing an increase Rd/wt/copy and decrease in latency with just a small bump, 3120T to 4041T, in tREF.
I'm running 3 instances of MemTest to 100% between jumps so it might take a while but I'll post a before and after when I'm all done.

Thanks

[Bitgod]

Do you guys like using OCCT? I hadn't tried it until this system, always used Prime 95. I'm trying to figure out why OCCT fails after 5 mins at the current speed, but Prime 95 had no problems doing 4 threads for 3 hours. I don't consider 3 hours a final test, I usually go 8-9 hours for that, I just hadn't settled on a final setup yet. Should I trust OCCT and assume that P95 just hasn't caught what OCCT has?

[zfactor]

well x38 is gone so ill be here with the x48 soon as i get it.. cant wait for it!!!

[zfactor]

can someone please explain the issue with the 3807x2 what is the problem exactly??

[TouGe]

ZenEffect

When you set tREF in MemSet does it save your settings upon reboot? I can set tREF to 14592T and run Everest cache and bandwidth benchmark and see the improvements but once a reboot MemSet resets tREF to 4041T. Is there a way I can make this change permenent so that I don't have to reset tREF everytime I boot my computer?

Thanks.

..................................................

Nevermind, figured it out. You first have to delete your old save before you can apply a new one.

[MacClipper]

can someone please explain the issue with the 3807x2 what is the problem exactly??

http://csd.dficlub.org/forum/showthread.php?t=5931

[wilson]

Ok now ive managed to get 4005Ghz stable on my E8400 but i need 1.39v as any lower i fail in occt. Without sounding stupid how can i get my v-core to 1.38v and stay there as ive tried the 100.23% with almost all volt settings and i can get 1.39 constant or 1.39 idle and 1.37 load but this make`s occt fail. If i could get 1.38v to stick at load and idle then i would be happy as i could test it in occt because 1.39 seems alot for a 4ghz overclock..

[emoners]

what are good DDR3s that could nicely go with this board?

[ZenEffect]

what are good DDR3s that could nicely go with this board?

this is a ddr2 motherboard...

[wilson]

Ive just run occt for a 2nd time just to be sure im 100% stable with the following settings. This has taken me 4 days to get right and these are the only settings that give me a pass.




I have my GTL`s @ 85 83 66 .

[Big Lar]

Ive just run occt for a 2nd time just to be sure im 100% stable with the following settings. This has taken me 4 days to get right and these are the only settings that give me a pass.




I have my GTL`s @ 85 83 66 .

Just for a try, maybe try 1.104v VTT and 65/64/63 for the GTL's. Until I refined the GTLs on my setup, my settings were just about the same as yours, except my NB shows 1.45V in SG.(1.479v in bios). Just trying to help.

Larry

[davewolfs]

Can this board run stable with 4 sticks and 8GB or not really recommend?

[zanzabar]

Can this board run stable with 4 sticks and 8GB or not really recommend?

it will do 4sticks of the gskll 1000 (8GB) at 1080

[emoners]

this is a ddr2 motherboard...

oppss sorry, i had multiple tabs opened in firefox

[BadNizze]

Anyone tryd DFI Lanparty UT X48-T2R? Getting my today aswell as an E7200 Is there anything I should know before I boot here upp for the first time? Issues, Buggs...?

System
E7200
DFI Lanparty UT X48-T2R
Corsair Dominator PC8888 CL4\Cellshock PC9200 CL5
2600XT
Corsair HX520W