**Official DFI LanParty UT X48-T2R(and LT) Discussion

[CoolZone]

I appreciate your input zsamz_,I will not change the NB cooler after hearing this stuff.I am now looking for a PWM cooler and a SB cooler.Any recommendations?The CPU cooler will be a TR Ultra Extreme.

[NoobCake]

SO guys, for the DDR2 range from DFI, the DFI X48 UT T2R will be the most dominate one?

[axis]

SO guys, for the DDR2 range from DFI, the DFI X48 UT T2R will be the most dominate one?

Probably not. I think most will go for the the LT since they will most likely WC it. I don't see the need to use it for aircooling either. Unless i'm mistaken, it's the same mb with heatpipes instead of individual heatsinks.

Axis

[Booj]

Anyone knows, if these board supports the Tuniq Tower 120?

Thank's

No problem, but the orientation is only one way. Having it in a case with the fan blowing to the rear is a no go

[CoolZone]

Is there at least someone having the DFI X48 setup in a case?

[clone38]

Mips blocks arrived this moring for my board,now i have just got to buy it

Packed well.











Northbridge.



Southbridge



Mosfet even supplyed free paste

[Jor3lBR]

Mips blocks arrived this moring for my board,now i have just got to buy it

Packed well.

Mosfet even supplyed free paste

They look exactly what we pay for astonishing!

[Tjalve]

Is there at least someone having the DFI X48 setup in a case?

I Do:

[ACE76]

I just got my DFI X48 and 4gig of of OCZ Reaperx and Q9450 from tank guys I am having alot of issues getting this to overclock. Anyone have some setting I can start with ? 3.2 is all I can get so far.. there are so many setting in the bios

what is everyone running for NB volts and CPU VTT


Thanks !

I got a Q9450 from Tank guys as well but it's defective...one of the cores keeps on crashing when I stress it...this is all at stock speeds and volts...I've sent them an E-Mail about it and they seem to be ignoring me. The temps on this CPu are all over the place too...I see it idle at 27c sometimes and then at other times it's idling at 46c.

[X2beach]

Ace76, Mine is the same way at Stock mine Crashes also, they are RMA mine, but what sucks is I have to send it back to them then they are going to send it to Intel and so 3-4 weeks with no CPU this is my last time buying from them

[Dimek]

They look exactly what we pay for astonishing!

Bottom is not so clean and flat... but it's still worth buying

[CoolZone]

I Do:

I can't see the photo

[clone38]

They look exactly what we pay for astonishing!

they sure do mate.

[zsamz_]

I appreciate your input zsamz_,I will not change the NB cooler after hearing this stuff.I am now looking for a PWM cooler and a SB cooler.Any recommendations?The CPU cooler will be a TR Ultra Extreme.

replacing pwm cooling is bs just lap it slightly n replace the springs mine never goes higher than 35c full load use mx2 on everything

i even moded mine with a laptop heatpipe only 1c drop all pwm needs is good are circulation n good springs

[zsamz_]

Ace76, Mine is the same way at Stock mine Crashes also, they are RMA mine, but what sucks is I have to send it back to them then they are going to send it to Intel and so 3-4 weeks with no CPU this is my last time buying from them

are you serious 3-4 weeks who is that garbage retailler

[X2beach]

zsamz, I bought it from tankguys, basically I have to send my cpu to them, then they RMA to Intel

not very impressed with there Customer Services ..

[zsamz_]

zsamz, I bought it from tankguys, basically I have to send my cpu to them, then they RMA to Intel

not very impressed with there Customer Services ..

thats pure bs in my book my old retailer gave me a new cpu on the spot after a month of use
now i buy from ncix they got even better service

[PnoT]

I'm still having issues with my board when applying more than 1.26v to the proc. The thing just shuts down and refuses to reboot. I hope they figure this problem out soon because it's really tainting my opinion of this board.

If anyone else is having this issue you might wanna stop by and check out the thread here: http://csd.dficlub.org/forum/showthread.php?t=6175

Here is also a video that someone posted on how the board acts when this happens: http://tinypic.com/player.php?v=260fp8i&s=3

[Jultsu]

ooo-kay guys. I just ordered this board to replace my crappy nvidia 650i board. Last DFI board I owned was the nf4 SLI-DR, that thing was a to work with. Hope they've improved from those days

[Eldonko]

How much all those blocks run you clone38? They look nice..

[CoolZone]

replacing pwm cooling is bs just lap it slightly n replace the springs mine never goes higher than 35c full load use mx2 on everything

i even moded mine with a laptop heatpipe only 1c drop all pwm needs is good are circulation n good springs

Thanks again for your help.Can you make a photo please with the modifications for the PWM cooler?I am interested to see those springs you talk about.Thanks in advance.

[Fluke_Dallas]

I got a Q9450 from Tank guys as well but it's defective...one of the cores keeps on crashing when I stress it...this is all at stock speeds and volts...I've sent them an E-Mail about it and they seem to be ignoring me. The temps on this CPu are all over the place too...I see it idle at 27c sometimes and then at other times it's idling at 46c.

I'd try the cpu on a motherboard other than the DFI X48 before doing the RMA. I think there is some strange incompatability going on. When I put my E6600 in the board it goes straight to FSB 500 no sweat. Put the Q9450 I got from Tankguys in and I struggle to get to FSB 400. Multies at 6x on both. Be a shame to return the CPU and find it ok.

[zsamz_]

Thanks again for your help.Can you make a photo please with the modifications for the PWM cooler?I am interested to see those springs you talk about.Thanks in advance.

i not gonna take board apart
just lap pwm with 600 grit till you get the paint off
the original springs are too weak not enough pressure
i put in screws and better springs n made sure every pwm getting proper contact

[axis]

i not gonna take board apart
just lap pwm with 600 grit till you get the paint off
the original springs are too weak not enough pressure
i put in screws and better springs n made sure every pwm getting proper contact

I didn't lap mine but took it off, scraped all the crap off and reseated it with some TIM that came with my TRUE. It was the only stuff I had that was 100% nonconductive. I don't have a temp probe on the area but it's always cool to warm to the touch.

Axis

[Jor3lBR]

I didn't lap mine but took it off, scraped all the crap off and reseated it with some TIM that came with my TRUE. It was the only stuff I had that was 100% nonconductive. I don't have a temp probe on the area but it's always cool to warm to the touch.

Axis

thats pure bs in my book my old retailer gave me a new cpu on the spot after a month of use
now i buy from ncix they got even better service

Ok do you guys know if Tuniq TX-2 is safe to use there?

Another question: did you guys only used the thermal paste on the original places (where use to be the DFI crapgoop) or did you guys also applied on the chips next to them?