Cpu-z 1.40.8

[Solarfall]

wohooo finally this new cpu-z reads my e6600 voltages correctly

[Slay0r]

Correct voltages reading on e4300/e4400/e4500 too

[Cracker]

I spoke too fast.
This should work this time.
http://www.cpuid.com/beta/cpuz.zip

Good work! Core voltage is now properly displayed with this latest version. (for the E6400 anyway)

[cky2k6]

this version makes my computer crash to the extent that the power button doesn't work, and i have to turn off the psu... never had that happen with cpu-z before.

[Nedjo]

I spoke too fast.
This should work this time.
http://www.cpuid.com/beta/cpuz.zip

One question.

since yesterday I'm on Vista x64 (with these prices of memory I want full usable 4GB working), and I was wondering would it be possible to compile CPU-Z for native 64bit??

There's CrystalCPUID (http://dl.crystaldew.info/download/C...PUID413x64.zip) but I much, much more prefer your awesome utill!

BR

Nedjo

[Marioace]

Mine doesnt shows correctly

according to CoreTemp VID is 1.35v

[higgins]

yep, reads my voltage correctly now and adds more spd info. thanks for the link mate

[ziddey]

cool. got rid of the 3rd decimal place, but cool. reads 1.50v like everything else now

[hecktic]

I spoke too fast.
This should work this time.
http://www.cpuid.com/beta/cpuz.zip

I think its fixed... but its not the same voltage though...

cpuz1.40.5 gives me 1.248 for VID

and the one I just downloaded gives me an exact 1.25 for VID

which one is accurate?

[cpuz]

this version makes my computer crash to the extent that the power button doesn't work, and i have to turn off the psu... never had that happen with cpu-z before.

Hum, could you please try to set PCI and Sensor to OFF in the ini file ?
Can you please directly send me your results by email ? I sent the address in a PM.

[cpuz]

I think its fixed... but its not the same voltage though...

cpuz1.40.5 gives me 1.248 for VID

and the one I just downloaded gives me an exact 1.25 for VID

which one is accurate?

Does it displays "Core VID" or "Core Voltage" ?

[cpuz]

Mine doesnt shows correctly

according to CoreTemp VID is 1.35v

I'll add the Fintek in the next version.

[ziddey]

I think its fixed... but its not the same voltage though...

cpuz1.40.5 gives me 1.248 for VID

and the one I just downloaded gives me an exact 1.25 for VID

which one is accurate?

It sounds like that's the actual voltage? If you had a 1.35v vid and exceeded the upper 1.4's, you'd be seeing 1.238v static in older cpuz. so 1.248 is something else

[revogamer]

woot voltage fixed for me too

[Cranox]

Reads core voltage wrong here , dumpfile is attached.
Vcore is in bios 1350v , cpu-z says 1.26v

[bing]

Thanks Franck !

Is it possible to put a the CPU VID there too ?

[3NZ0]

Cheers works a treat

[dinos22]

nice work Franck

[X.T.R.E.M.E_ICE]

1.40.8
1.40.5

These 2 versions don't work with Vista x64

[hecktic]

Does it displays "Core VID" or "Core Voltage" ?

err sorry it just says Voltage 1.248 v under cpz 1.40.5

1.40.8 says Core Voltage and it shows up as 1.25 V

I just noticed it uses a capital V and not lower case v like 1.40.5

So what is accurate here?

It sounds like that's the actual voltage? If you had a 1.35v vid and exceeded the upper 1.4's, you'd be seeing 1.238v static in older cpuz. so 1.248 is something else

According to core temp my VID is 1.3250

[Kunaak]

hey, where did the command rate go?

[safan80]

1.40.8
1.40.5

These 2 versions don't work with Vista x64

1.40.5 works fine under vista x64 but you have to run it as admin.

[joe.latino]

1.40.8
1.40.5

These 2 versions don't work with Vista x64

ehm also i have problems with 1.40.8 and vista x64:my pc always crash just running it,why?
ps. with old versions I hant any problems
thanks

[NickS]

Voltage & everything works great here, thnx Mr. CPU-Z

[gdogg]

At first, I couldn't run it from vista x64, it would just crash, then I downloaded it again, ran directly from winrar, it worked .

Now i have extracted it, and it still works, good stuff added, like the proper voltage readings with my e6600.