The Official Core 2 Duo Overclocking Thread

[Dietka]

your ram will do 500mhz at 5.4.4.9,so why have you got it at 5.5.5.15 at only 480mhz? surely it will run that 480mhz at slightly lower timings.

on my p5b-d,my 6300 will do 3.5ghz(500fsb) with vcore at 1.4 with ram at 1000 1:1.your ram is rated for 500 anyway,so why not give it a try? temps at that are about 40-41c idle and about 61-63maxxed with a freezer 7 pro.

I allready tried 500mhz and i get my system so grazy that i have to take battery of and do that jumper trick . Now i have 4-4-4-9 and 440mhz E6300 is 3Ghz, just finding good 24/7 clocks, first Intel to me and before this iv only clocked one AMD Opteron and thats my overclock history thats why some settings can be so wrong, but i take advises and learning english too

[alpha0ne]

on my p5b-d,my 6300 will do 3.5ghz(500fsb) with vcore at 1.4 with ram at 1000 1:1.

That sounds like an exceptional E63, what week/stepping is it ??

[ingenue007]

i put some copper HS on the motherboard near the heatpipe and am getting a couple more mhz and stable with orthos 4+ hours. now at 483 with my e6300.

[dinos22]

That sounds like an exceptional E63, what week/stepping is it ??

wonder what superlative you'd use on this one then hehehe


514MHz FSB 3.6GHz CPU 1.38V Load Windows
30 minutes Orthos Prime >>> HZ sticks 4-4-4-12 2.3vdimm

[alpha0ne]

wonder what superlative you'd use on this one then hehehe

514MHz FSB 3.6GHz CPU 1.38V Load Windows
30 minutes Orthos Prime >>> HZ sticks 4-4-4-12 2.3vdimm

Well I would'nt normally use those words with you dino just in case ya dont fully understand them

and your E6300 is an ES (especially sweeeet) so no superlatives are needed apart from "give it to MEEEEEEEEEE".....................hehehehe

Oh and it still needs a whole 0.10 Vcore more than my E66 to run @ 3.60GHz

[TI66ER]

@alpaone,my codes are-L629B405 SL9SA.mines a retail tho' es pah lol

i'm sure mine will do that 3.6ghz too.probs do the 3.5ghz at 1.38v too.i cant go over 500fsb tho' coz i dont think my ram will do more than 1000mhz.

[Dani]

E6600 L630A
ASUS P5W64WS Pro with official BIOS 0304
Watercooled CPU & NB, water +26'C
From BIOS 1.325Vcore, Probe 1.35V and measured 1.372V, well done ASUS

[The Legend]

Asus P5B Deluxe/WiFi
E6400 L628a
Tuniq Tower 120
Crucial 2GB DDR2 667/4.4.4.15

So far Orthos stable-1 hr. 32 min.
Load temps 56c/60c TAT

[Dani]

E6600 L630A
ASUS P5W64WS Pro with official BIOS 0304
Watercooled CPU & NB, water +26'C/79F
From BIOS 1.300Vcore, Probe 1.33V and measured 1.33V, hmm, this is correct then

[TI66ER]

heres my e6300 at 506fsb 3.55ghz(1.4vcore set in bios) with ram at 1012mhz 1:1 at 2.35vmem

[alpha0ne]

heres my e6300 at 506fsb 3.55ghz(1.4vcore set in bios) with ram at 1012mhz 1:1 at 2.35vmem

Can you borrow/beg/steal some decent ram to try for 3.60GHz ??

You could try using just one stick single channel that should allow you to hit 3.60GHz

[TI66ER]

it seems my ram is decent,i did get 3.6 last nite-



vcore at 1.4 and ram at 1030mhz 1:1

[alpha0ne]

it seems my ram is decent,i did get 3.6 last nite-

vcore at 1.4 and ram at 1030mhz 1:1

Is that ORTHOS stable ???

[TI66ER]

it is-

[Dani]

E6600 L630A
ASUS P5W64WS Pro with official BIOS 0304
Watercooled CPU & NB, water +26'C/79F
From BIOS 1.300Vcore, Probe 1.33V and measured 1.33V, hmm, this is correct then

[GameGuru]

When running Orthos is it normal to see 70*c under load? Idle is 40*c
Should I be worried when benching?
Vcore according to PC ProbeII is 1.46v but bios reads 1.5???

[alpha0ne]

it is-

For 2 minutes

[FragTek]

Finally got the Vapo hooked up... Here's my first OC attempt:

4Ghz
1.65vcore in BIOS
445FSB 1:1 @ 5-5-5-15
CPU Temp: ??? (Can't find anything that will read the CPU temp on this board when it's less than 0*c???)

[Raiden Zero]

old screen of my E6600ES

E6600ES
Gigabyte DQ6 F6 Bios
2048MB CellShock DDR800
Scythe infinity.

http://home.arcor.de/raidenzero/Comp...Vc%20small.jpg

Might go even higher with some better cooling. Gonna get my SS and a fully modded BadAxe within the next 2 weeks. 4.2Ghz shouldnt be too difficult.

3.6GHz->1.312V
3.7GHz->1.41V

raiden

[Dietka]

I get almost 3.4Ghz with 1.360(cpu-z) bus speed at 480mhz, maybe i could get 3.5Ghz if i put 1.5V to E6300, i think my Asus P5B AP aint go 500mhz Bus speed. Mems goes fine and i booted windows with 1200mhz 5-5-5-9.

Is this good or bad E6300 ?

[kempez815]

E6600 Retail

kempez815 - 3600MHz Dual Prime/Dual 32m PI Stable | 1.65v | Swiftech Apogee Water | Asus P5W DH Deluxe | Mushkin HP2 6400

[dnottis]

here is my retail box from Newegg 6300..

[tjelaw]

Finally got the Vapo hooked up... Here's my first OC attempt:

4Ghz
1.65vcore in BIOS
445FSB 1:1 @ 5-5-5-15
CPU Temp: ??? (Can't find anything that will read the CPU temp on this board when it's less than 0*c???)

nice, did u do any mods on the board? did u set fsb etc in bios or in windows with uguru?

can u give me some more info about voltage settings plz, thanks

[FragTek]

nice, did u do any mods on the board? did u set fsb etc in bios or in windows with uguru?

can u give me some more info about voltage settings plz, thanks

Completely stock unmodded board... Voltages / clocks set in BIOS, I don't believe in Windows/software clocking. Vdimm @ 2.2 and vmch @ 2.0.

[X.T.R.E.M.E_ICE]

so how good is the L628Axxx?

Just wondering what volts most of you use for 3.6GHZ stable?