2x1GB/1x1GB OC Database

[BRiT]

THunDA, mind if I ask what the batch number is on the stick they shipped back out to you?

[THunDA]

THunDA, mind if I ask what the batch number is on the stick they shipped back out to you?

C1115T.88
56278

Is that what you wanted to know ?

EDIT..
Here is my database entry at dfi-street with the settings in my sig..
http://www.dfi-street.com/forum/show...8&postcount=87

EDIT #2..
Last night I lowered the multi and started upping the htt to find the max of the ram .. I managed to pass 8+hours of prime at 290x9 with the same settings and voltages in my sig..


290 seems like the max prime stable speed.. I did get 295 to prime for an hour but thats it..

[RafaDel]

As many others experience, my first pair of Ballistix could do 300MHz prime and SuperPI stable at 2.9V. Sudenly after 2 months they started to show errors. RMAed to Newegg and got a new pair. Well now this new kit is having hard time to pass 285MHz

WTF very expensive memory now just performing poor range. Not sure if I should RMA them again...

May get an even worse pair

[Ampz]

I need me some ballistix!

[DanielDev]

As many others experience, my first pair of Ballistix could do 300MHz prime and SuperPI stable at 2.9V. Sudenly after 2 months they started to show errors. RMAed to Newegg and got a new pair. Well now this new kit is having hard time to pass 285MHz

LOL complaining about pc 4000 memory doing 285
that others got 300 doesnt mean that every pair goes 300.
It just means that they were very lucky

Remember, pc 4000 is supposed to do 250...

[e[N]eq]

I have noticed that there is a stability issue using memory dividers if you have a pair of ballistix with a large max FSB differenece, ie. one doing 260 and another doing 285+.
For instance I had a pair that one did 285 stable and another doing <260, in that setting 200 and 183 was usable but no other (except 100). I would get reboot cycles when entering windows if I even got that far.

I managed to get a more evenly matched set where each did 275 and no more problems.

Just speculation however, it might just have been one of the sticks being bad with memory dividers.

/Q

[Staucher]

Mushkin extreme Perfomance XP4000 (Samsung UCCC)

testing on
Abit AN8 Ultra
150 Opteron


268-3-4-3-8-1T/2.5V




285-3-4-4-8-1T/2.5V



Really well selects

[mucker]

mucker | 2x1GB G.Skill F1-3200PHU2-2GBZX - ??? | 3-3-2-5 1T @ 259 MHz | 2.75v | Link! - SPi 32M Stable: Yes

Pi32m


OCCT

[pentium777]

Just a quick note to all of you since I was among the first adopters of the Ballistix 2x1GB kits.

Apparently one stick flaked out randomly on me about a month ago, very strange random blue screens and finally after extensive testing found one stick to be bad slightly.

Even at defaults speeds etc it would sometimes show memtest errors, it was tough to troubleshoot because I put each stick on another PC (Intel based) and ran memtest 8 hrs no errors.

Crucial was quick to respond and RMA both sticks as the KIT, since then not one BSOD or failures. Hopefully this helps someone in the future that might have the same type of issue.

[hawkeyefan]

Samsung UCCC / Brainpower PCBs (mine showed up blue spreaders on green PCBs instead of black on black)

2.5v + .3v enabled
orange slots
704-2BTa bios

270mhz @ 3,4,3,8 1T
CPU-Z validation

memtest v1.65 30 passes


SuperPi 32M


3D stable


275mhz 3,4,4,8 1T
SuperPi 32M

http://valid.x86-secret.com/show_oc?id=54834

3D stable

http://valid.x86-secret.com/show_oc?id=54836

[bugeyes]

Test Rig specs:

A64 3000+ Venice E3
DFI NF4 Ultra Infinity
2x 1GB Corsair Value Select C3
Leadtek 7800GTX 256MB
TT Silent K8 HSF
Enermax 535w All in one
Windows XP Home.

VDIMM = 2.60 volts
Vcore = 1.40 Volts

CPUz Validation http://valid.x86-secret.com/show_oc.php?id=54859

[QettoE]

2x1GB Mushkin High Performance Model 991434.

Screenie:

Validation link: http://valid.x86-secret.com/show_oc?id=55107

I've got them yesterday from Newegg and haven't played around too much yet. I'm sure after more buring they will do better. I already like them a lot since they auto detect 2-3-2-5-1T on my DFI Ultra-D. After I RMA'd a pair of crappy OCZ OCZ4002048ELDCPE-K that didn't go past 208 at 3.0v and auto detected 2.5-3-2-5-1T I'm going to stick with these.

[Rubex74]

2x1GB GSKILL HX on MSI K8N Sli 250mhz 2.5-3-2-5 2.50V



http://valid.x86-secret.com/show_oc?id=51944

[alpha0ne]

2x1GB GSKILL HX on MSI K8N Sli 250mhz 2.5-3-2-5 2.50v

Nice

What Vdimm ??

[ElAguila]

Had my z503 ballistix less than a month at ddr520 and they flaked out on me. I am hoping the rma from newegg will be different batch.

[Rubex74]

Nice

What Vdimm ??

Tx, Vdimm is 2.50V.

BB

[HelloIDistance]

Mushkin extreme Perfomance XP4000 (Samsung UCCC)

testing on
Abit AN8 Ultra
150 Opteron


268-3-4-3-8-1T/2.5V

285-3-4-4-8-1T/2.5V

Really well selects

Nice results! I have the same kit, but I have it running in an Nforce2 motherboard ATM

The VDIMM is pretty low, does it seem like it does better with lower voltage?

[hawkeyefan]

Nice results! I have the same kit, but I have it running in an Nforce2 motherboard ATM

The VDIMM is pretty low, does it seem like it does better with lower voltage?

I can't speak for Stauncher obviously, by my experience so far with the same sticks has been that 2.5v-2.65v is optimal and that anything more just increases instability and errors.

[hawkeyefan]

Nice results! I have the same kit, but I have it running in an Nforce2 motherboard ATM

The VDIMM is pretty low, does it seem like it does better with lower voltage?

I can't speak for Stauncher obviously, by my experience so far with the same sticks has been that 2.5v-2.65v is optimal and that anything more just increases instability and errors. I noticed an increase in errors below 2.5v as well. Mine are best right at 2.60v.

[Staucher]

I can't speak for Stauncher obviously, by my experience so far with the same sticks has been that 2.5v-2.65v is optimal and that anything more just increases instability and errors.

Exactly the same run at best with 2.5-2.6V the more brings only nothing.
Very Good Mushkin

[JNav89GT]

I can't speak for Stauncher obviously, by my experience so far with the same sticks has been that 2.5v-2.65v is optimal and that anything more just increases instability and errors. I noticed an increase in errors below 2.5v as well. Mine are best right at 2.60v.

2.6 is about max for me as well
Mushkin UCCC is very very easy to work with

[Squire]

2.6 is about max for me as well
Mushkin UCCC is very very easy to work with

JNav89GT- Stop being a mushkin whore. All your posts seem to be about praising or defending mushkin.

[Blue078]

JNav89GT- Stop being a mushkin whore. All your posts seem to be about praising or defending mushkin.

He cant, hes on the payroll

[STEvil]

or beta team at least.

show some more respect.

[cronic]

my results sent
here are my results with this memory ddr550 @ 2.7v 2750Mhz
F1-4000USU2-2GBHZ
http://tinypic.com/imibg1.jpg
http://tinypic.com/imibly.jpg