DFI LANparty DK P45-T2RS/T3RS (Intel P45) - News|Info|Results

[Eldonko]

Same problem with my JR, PI is fine at high FSB but long term is not possible. Running OCCT it usually errors out at the 4 hour mark at the longest.

Allthough my E8600 primes at 9x500 for 8 hours straight , it can't do more than 5 minutes on 7x600. SuperPi wil run, that's no problem, but then agian i doesn't strain the system that much.

[C-N]

The only thing I've done interesting all week is make up/tweak Smartguardian using a skin a (DJSUB) posted up in the P35 thread & re arrange the .ini so it all fits in a box the size of core temp. I'll post it up later for anyone that want it.

Here it is do what you like with it.

CN

[DemonEyez]

Same problem with my JR, PI is fine at high FSB but long term is not possible. Running OCCT it usually errors out at the 4 hour mark at the longest.

Well, I finally managed to get some semi-stable settings for 7x600.
i've been Priming for one hour and a half now

Only downside is that I have to set 'Enhance Data transmitting' and 'Enhance Addressing' both to Normal, which has a rather large impact on bandwith and latency. Overall it's even lower than running at 500MHz and both set to Fast or AUTO.
So allthough it seems to be stable for long term use, it's not very interesting compared to my 500fsb setting for 24/7 use which give more overall performance.

I think reviewers should be more conservative instead of shouting that the
P45 T2RS plus is every overclockers dream with setting a 600MHz bus. They should first test it for long term stability before they make such a statement

[Vazovskiiii]

can anybody write down settings for me i have DFI LANPARTY DK P45 T2RS and cpu is Q6600 ram is Team Xtreem 6400, 4-4-4-10 timings micron D9GMH chips plz i'm new one and need help to overclock very dificult.

[Tal Bar]

You can find all needed settings here http://csd.dficlub.org/forum/showthread.php?t=8079 and here ftp://ftp.dfi.com.tw/ you can find OC guideline. Enjoy :o)

[Vazovskiiii]

You can find all needed settings here http://csd.dficlub.org/forum/showthread.php?t=8079 and here ftp://ftp.dfi.com.tw/ you can find OC guideline. Enjoy :o)

thank you very much
but there is not writing anything about overclock Q6600

[C-N]

Here's my new daily overclock all but I'll put her on water & get RAID going when I change cases with my server later next week.

I reckon I could lower the NB voltage a click or 2 or maybe even more if I dropped back to the 333 strap.

CN

P.S Sorry about the BIOS version typo in SG

=========================

DFI LANPARTY DK P45-T2RS (BIOS 1003)

INTEL CORE 2 DUO E8500 WOLFDALE 3.16GHZ 6M L2 CACHE (Q807A273 / C0)

OCZ PC2-8500 SLI 2 x 1GB PN:OCZN1066SR2GK

VISIONTEK HD3870X2 1GB OC 904 X 1053MHZ (8.10 DRIVERS)

1 X HITACHI DJ 80GB HD'S

SONY DUAL LAYER DVD RW (DRU-820A)

OCZ GAMEXTREAM 700W PSU

WINDOWS XP PRO SP3

CPU COOLING: AIR / TRUE & 100CFM PANAFLO

>CPU Feature:
 
Thermal Management Control.......... - Enabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Enabled
Virtualization Technology........... - Enabled
Core Multi-Processing............... - Enabled
 
>DRAM Timing:
 
Enhance Data transmitting........... - Fast
Enhance Addressing.................. - Fast
T2 Dispatch......................... - Auto

>Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - Auto
Ch1 Dram Defaul Skew................ - Model 3
Ch2 Dram Defaul Skew................ - Model 3
RCOMP Settings...................... - Model 1

Fine Delay Step Degree.............. - 70ps
Ch1 Clock Crossing Setting.......... - Nominal
DIMM1 Clock Fine Delay.............. - Current[2396ps]
DIMM2 Clock Fine Delay.............. - Current[2396ps]
Ch1 Control0 Fine Delay............. - Current[268ps]
Ch1 Control1 Fine Delay............. - Current[268ps]
Ch1 Control2 Fine Delay............. - Current[268ps]
Ch1 Control3 Fine Delay............. - Current[268ps]
Ch1 Command Fine Delay.............. - Current[394ps]

Ch2 Clock Crossing Setting.......... - Nominal
DIMM3 Clock Fine Delay.............. - Current[2066ps]
DIMM4 Clock Fine Delay.............. - Current[2066ps]
Ch2 Control0 Fine Delay............. - Current[48ps]
Ch2 Control1 Fine Delay............. - Current[48ps]
Ch2 Control2 Fine Delay............. - Current[48ps]
Ch2 Control3 Fine Delay............. - Current[48ps]
Ch2 Command Fine Delay.............. - Current[394ps]

Ch1 Ch2 Common Clock Setting........ - Nominal

Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto

Flex Memory Mode..................... - Auto
CAS Latency Time (tCL)............... - 5
RAS# to CAS# Delay (tRCD)............ - 5
RAS# Precharge (tRP)................. - 5
Precharge Delay (tRAS)............... - 10
All Precharge to Act................. - 5
REF to ACT Delay (tRFC).............. - 28
Performance Level.................... - 7

>Read delay phase adjust Press Enter:

Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto

Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto

Write to PRE Delay (tWR)............ - 12
Rank Write to Read (tWTR)........... - 11
ACT to ACT Delay (tRRD)............. - 3
Read to Write Delay (tRDWR)......... - 8
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - 4
ALL PRE to Refresh.................. - 4

>Voltage Settings:

CPU VID Special Add................. - + 450.0mV
DRAM Voltage Control................ - 2.243v
SB Core/CPU PLL Voltage............. - 1.55v
NB Core Voltage..................... - 1.4075v
CPU VTT Voltage..................... - 1.25v
VCore Droop Control................. - Disabled
Clockgen Voltage Control............ - 3.60v
CPU GTL0/2 REF Volt................. - 0.67x
CPU GTL 1/3 REF Volt................ - 0.67x
North Bridge GTL REF Volt........... - 0.58x
FSB Vref............................. - Auto
 
Genie BIOS Settings:
 
Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
O.C Clock Fail Retry Counter........ - 0
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 9.5
Target CPU Clock.................... - 4493MHz
CPU Clock........................... - 473
Boot Up Clock....................... - Auto
CPU Clock Amplitude................. - 800mV
CPU Clock0 Skew..................... - 0ps
CPU Clock1 Skew..................... - 0ps
DRAM Speed.......................... - 266/667
Target DRAM Speed................... - 1186MHz
PCIE Clock.......................... - 100mhz
CPU Spread Spectrum................. - Disabled
PCIE Spread Spectrum................ - Disabled

PRIME95 + 3x CPU-Z



EVEREST CACHE & MEMORY:(READ 10448MBS LATENCY 48.5NS)

http://i106.photobucket.com/albums/m...emoryBench.jpg

3DMARK2001:(SCORE 81249)

http://i106.photobucket.com/albums/m...6/3DMARK01.jpg

3DMARK2003:(SCORE 75560)

http://i106.photobucket.com/albums/m...6/3DMARK03.jpg

3DMARK2005:(SCORE 29838)

http://i106.photobucket.com/albums/m...6/3DMARK05.jpg

3DMARK2006:(SCORE 20131)

http://i106.photobucket.com/albums/m...6/3DMARK06.jpg

AQUAMARK 3:(SCORE 265,324)

http://i106.photobucket.com/albums/m...6/AquaMark.jpg

SHORT DESCRIPTION:
473 x 9.5 = 4500MHz @ 1.45v
5-5-5-10 2T @ 2.24V DDR 1186

[emoners]

@C-N: nice OC! is it safe to get VDIMM @2.243v for 24/7?

[C-N]

@C-N: nice OC! is it safe to get VDIMM @2.243v for 24/7?

Thanks bud,

I am more worried about the vcore with this CPU its a low vid hot one but it has run 24/7 on water for a couple of months so we'll see

My OCZ's are the old proper D9 ones they were rated at 2.35v + - 5% when I purchased them. OCZ later revised this to 2.3v max & now there new kits are 2.1v max. I always cool them well too.

http://www.ocztechnology.com/products/memory/ocz_ddr2_pc2_8500_sli_ready_edition_dual_channel

I don't run my main/play rig 24/7 anymore I now have a home server made up from the dead for that. Also XP & Vista now boot to desktop much quicker these day.

[lessonz]

Okay, I didn't read every post, but I did search them. Anyone have a T2RS with a Big Typhoon VX mounted on there? Any clearance issues?

[Bullet92]

I have serious problem here. I have non plus version and did 600MHz FSB at first run with no extra voltages (all def. except vNB = 1.4V and vram at 2.2V). That's pretty nice result for non plus version BUT I can't pass over 400MHz stable now. Tried with 4 kit's of RAM, flashing BIOS, different settings than that for 600MHz (much higher voltages) and so on and so on but nothing happened
I really don't know what it can be except crappy board. I have had much mobo's but never had problem like this one. Sometimes I can't reach the same FSB but that difference is in 10-20MHz not in 200MHz. I'm really confused...

[Eldonko]

Was 600 stable in the first place? I highly doubt it if you used stock voltages..

[C-N]

I have serious problem here. I have non plus version and did 600MHz FSB at first run with no extra voltages (all def. except vNB = 1.4V and vram at 2.2V). That's pretty nice result for non plus version BUT I can't pass over 400MHz stable now. Tried with 4 kit's of RAM, flashing BIOS, different settings than that for 600MHz (much higher voltages) and so on and so on but nothing happened
I really don't know what it can be except crappy board. I have had much mobo's but never had problem like this one. Sometimes I can't reach the same FSB but that difference is in 10-20MHz not in 200MHz. I'm really confused...

Theres a fsb hole or a bit that dont run too nice (you choose) between 400 & 450fsb. It depends on what memory divider you are on as to how big the hole is 1:1 I think the hole ends about 420~425fsb, try 450fsb & see what happens.

[Bullet92]

Was 600 stable in the first place? I highly doubt it if you used stock voltages..

Of course not, just finding max fsb but I stopped because it was too late and I left the searching for tommorow but day after I couldn't reach over 400MHz.

Theres a fsb hole or a bit that dont run too nice (you choose) between 400 & 450fsb. It depends on what memory divider you are on as to how big the hole is 1:1 I think the hole ends about 420~425fsb, try 450fsb & see what happens.

Yes I know that and I already tried that.
400 -> boot normaly, stable
420 -> boot screen, crash
430 -> no boot
450 -> no boot
470 -> no boot
500 - > no boot
That speeds are with different voltages but no success. Divider was 1:1 but I tried other also and as you see, no success. Very weird
As I said, I have a lot of experiences with mobo's but that looks like ready for RMA.

[Eldonko]

My review is live now (for the JR), I think it should be more representative of a common retail board as it did not come directly from DFI.

http://www.hardwarecanucks.com/forum...rd-review.html

I think reviewers should be more conservative instead of shouting that the P45 T2RS plus is every overclockers dream with setting a 600MHz bus. They should first test it for long term stability before they make such a statement

[PolRoger]

My review is live now (for the JR), I think it should be more representative of a common retail board as it did not come directly from DFI.

http://www.hardwarecanucks.com/forum...rd-review.html

Interesting read. I agree this board is not that easy to get high fsb overclocks out of the box. The auto bios settings on my TPower I45 allowed for a faster overclock experience when it was first new to me. The DFI LP JR and its detailed bios settings do seem to require a longer learning curve.

I've had my board for a little over a month now and yesterday it started acting flaky with fluctuating VID settings on my E8600. I tried a different power supply and flashing to different bios but it didn't seem to help. I swapped over all the components including hard drive and O.S. to my TPower board and so far I'm not experiencing any further problems. The LP JR is now resting without a battery. I'm going to have to go back and investigate some more in a few days.

I never did get to do long term 24/7 (reasonable voltage) stabilty testing on my LP JR. When you were doing your fsb 500+ 5hr OCCT tests were were you running "mix" or a combination of all three?

[Eldonko]

OCCT Mix 5 hour. I got to 4 hours a few times but not further than that. Took me 3 days of work to even POST @ 500 lol, had to have the perfect skew/gtl mix and was not possible without adjusting the hidden BIOS settings.

[emoners]

My review is live now (for the JR), I think it should be more representative of a common retail board as it did not come directly from DFI.

http://www.hardwarecanucks.com/forum...rd-review.html

very nice read Eldonko! thanks! i'm still working on the small quirks of this board with my Q6600...even got me thinking of getting a dual core

[nikk]

e8400 600x6 done

straight boot from bios

validation

superpi 1m


everest


superpi 32m


3dmark06


aircooled with noctua nu6 on nb

[emoners]

@nikk: is that stable? nice oc!

[nikk]

@nikk: is that stable? nice oc!

thx
i run all you see above after boot from bios, one after another, no problem
haven't tried anything else

[namegt]

e8400 600x6 done

straight boot from bios

validation

superpi 1m


everest


superpi 32m


3dmark06


aircooled with noctua nu6 on nb

FSB600x6 nice
IBT is available for testing?

[nikk]

Ibt??

[Pcuser]

e8400 600x6 done

straight boot from bios

validation

superpi 1m


everest


superpi 32m


3dmark06


aircooled with noctua nu6 on nb

Nice
I can boot my E8600 on air to 600fsb as well.
655fsb is the max fsb done on vapochill LS

[namegt]

Sorry. IBT = intelburn TEST ^^;;

600x6
intelburn 5 passes Can I do that?