abit ab9 quad gt voltage readout points

[fgw]

hi folks

has anybody already found voltage readout points on the abit ab9 quat gt?

received the board yesterday and want to solder some wires before i install the board into my case.

i'm looking for pics of readout points: vcore, vmch, vdimm, vtt

don't know yet hows the voltage drop on this board. will figure it out as soon as i know the readouts. drop mod might be of interest too ...

hipro?

THANKS

[syn7h37ic]

hi folks

has anybody already found voltage readout points on the abit ab9 quat gt?

received the board yesterday and want to solder some wires before i install the board into my case.

i'm looking for pics of readout points: vcore, vmch, vdimm, vtt

don't know yet hows the voltage drop on this board. will figure it out as soon as i know the readouts. drop mod might be of interest too ...

hipro?

THANKS

Here is the points http://prohardver.hu/p.php?mod=40&id...tart=463&len=1

[syn7h37ic]

Here is the points http://prohardver.hu/p.php?mod=40&id...tart=463&len=1

This is the pictures.

[Hazzan]

Any knows vdrop mod for this board ?

[Johnny Bravo]

Any knows vdrop mod for this board ?

Good luck mate. the VT1115M is under NDA and a number of us have tried to get hold of it, with no avail. Either someone manages to get a copy or we're stuck with only BIOS mods.

[fgw]

Johnny Bravo, can you confirm the readout points posted by syn7h37ic?

dont understand hungary and don't want to solder unneccessary cables to my board!

just want to double check before heating up my soldering iron ...

THANKS

[Johnny Bravo]

Johnny Bravo, can you confirm the readout points posted by syn7h37ic?

dont understand hungary and don't want to solder unneccessary cables to my board!

just want to double check before heating up my soldering iron ...

THANKS

Will get something up tomorrow nite, for tonite I'm otherwise detained

[fgw]

Will get something up tomorrow nite, for tonite I'm otherwise detained

so, wish u a nice evening/night!

THANKS

[boblemagnifique]

up

Any vmod ?

[ztop]

where is the voltage readout points for ddr2 voltage?
thanks

[crotale]

This is a general picture, valid for all DDR2 motherboards.
If you need a permanent spot, do a contingency check (0 ohm) from this point to capacitors at theside of the dimm slot and solder a wire to it.



(Up in this picture is up on regular Intel boards, but some might have the slots reversed)

[Achill3uS]

guys, anybody knows some vmod for this board? (NB is the more important)
i sent pm to hipro and he works on it, but if somebody have some info, or pics, or everything else about the QuadGT vmods, please tell here

[Johnny Bravo]

Vmods so far







Crotales vdimm should work fine on this board too


Hoping to have vcore sorted soon along with a vdroop, for vcore measurements just try the side of the ceramic SMD capacitors around the cpu socket - one side will be grounded and the other will be vcore.

[Achill3uS]

thank you Johnny Bravo, I hope they works fine!

[boblemagnifique]

I Vmod Others Point (similar ) , Spécial Thank a Shamino and Learn

[ztop]

any v-mod for the v-drop?

[hellas91]

any v-mod for the v-drop?

Some news?

[Achill3uS]

hipro help us

[DEVIL K-ce]

I look for vcore mod and hmmm

Hipro say vcore mod from IN9 Max might be the same for Quad GT.

For me this is not the same

Check this foto : this is IN9 Max vcore mod



What about this guys ?

The same or not ?

Regards
Martin

[Johnny Bravo]

I'll have vdroop and vcore up before the nite Just waiting for the cable back for my camera

[Johnny Bravo]

Vcore



Vdroop



Don't try to completely eliminate vdroop it's needed for the cpu to function normally but I've been able to reduce it to less than 10mV

Enjoy

John

[Misko]

Don't try to completely eliminate vdroop it's needed for the cpu to function normally but I've been able to reduce it to less than 10mV

Enjoy

John

Great vmods Johnny , can u put some more info abut why is necessary to have some small vdrop?

[DEVIL K-ce]

Man Very, very big thanks for this mod's.



Martin

[Johnny Bravo]

Great vmods Johnny , can u put some more info abut why is necessary to have some small vdrop?

Hey Misko - you'll find all you need to know right here:

http://www.thetechrepository.com/showthread.php?t=126

[blossa]

Don't try to completely eliminate vdroop it's needed for the cpu to function normally but I've been able to reduce it to less than 10mV

Enjoy

John

I am running out of VR. Can you measure the actual resistans of your VR only when you have about 10mV drop?

Thanks in advance!