What is your max overclock for E6600 on stock voltage?

[N15M0]

Mine on stock voltage can pass dual 32m Spi at 310 x 9 but cannot pass sp2004. Week 24. I have my mch at +0.35. Any other way to increase the oc other then increasing vcore?

[fhpchris]

mine did ~330fsb*9 = 2950 ish on stock voltage

Did ~3.7 @ 1.65v

[N15M0]

mine did ~330fsb*9 = 2950 ish on stock voltage

Did ~3.7 @ 1.65v

That is better then mine. Is it the week 24 batch? Also what other setting you set? Like what is your vmch? Thanks.

[Supertim0r]

66es at 3.4ghz

[N15M0]

66es at 3.4ghz

Stock vcore? Other setting like vmch?

[pcdoc1]

What are we calling "Stock Vcore"? Surely can't be "Auto"....

[Supertim0r]

all auto except vdimm
p5b dx

[N15M0]

Stock vcore is 1.3 right for conroe. Btw does putting auto on vcore increase the vcore?

[pcdoc1]

all auto except vdimm
p5b dx

Wow, auto gives me 1.55 @ 3.6, can that really be defined as "stock"...

[pcdoc1]

Stock vcore is 1.3 right for conroe. Btw does putting auto on vcore increase the vcore?

I think 1.35 is defined by Intel...

[Lestat]

1.237 is stock on the DS3
and you gotta watch it with these board they DO raise the vcore when left on auto.

i would say double verify what is stock for a 6600 and manually set it to that.
otherwise voltage will rise.

mine is somewhere between 3.2 and 3.3 on stock i cant recall.
i can do stock ghz 2.4ghz @ 0.975v lol.

[syne_24]

my max is 333x9 with auto volt + eist and all the power goodies enabled

[irev210]

~3500-3600 @ 1.35vcore depending on the mobo

not exactly "stock" but whatever. Good enough for me.

e6600 es, step5

[pcdoc1]

Well hell, this is fun…. Looks like Asus’s bios engineers are better clockers than we are…

Bios defaults, everything set to auto except vdimm (2.15)….

[orion23]

The P5B deluxe is know for upping the Vcore to 1.5 and above under "AUTO" mode. You need to set it to 1.3 or so in order to run "default" values, otherwise, you are running at least 1.5

[pcdoc1]

The P5B deluxe is know for upping the Vcore to 1.5 and above under "AUTO" mode. You need to set it to 1.3 or so in order to run "default" values, otherwise, you are running at least 1.5

Three cheers... Default has already been define for this thread...

[vintage_guitar]

wow.. that's a cpuz bug for displaying 1.45volts+.......always shows that 1.213

[pcdoc1]

Who cares if you monitor vcore with a different app.....

[fhpchris]

That is better then mine. Is it the week 24 batch? Also what other setting you set? Like what is your vmch? Thanks.

It was a week 23.

[N15M0]

1.237 is stock on the DS3
and you gotta watch it with these board they DO raise the vcore when left on auto.

i would say double verify what is stock for a 6600 and manually set it to that.
otherwise voltage will rise.

mine is somewhere between 3.2 and 3.3 on stock i cant recall.
i can do stock ghz 2.4ghz @ 0.975v lol.

What is the stock vcore for DQ6? Is it the same as the ds3 at 1.237?

[cooleye]

Mine is week 24, and I use the asus OC profile, which goes to 333X9=3.0G and the vcore is 1.12 idle (X6) and 1.28 underload (X9), which is dual prime stable over 24 hours. The temp is 37 idle and 53 full load. All from PC probe, but core temps and cpuz agrees very well for the temp and volt.

[pcdoc1]

Going OT again aren't we.... Geezzzz

[cooleye]

Going OT again aren't we.... Geezzzz

What is OT ?

[irenic]

mine week 24 does 335x9 @ 1.35vcore set in bios p5b dlx. during load it drops to 1.32 in asus pc probe.. stable orthos

[Revv23]

What is OT ?

Off Topic, i dont think he was refering to you though, but the poster before you.