How to overclock FSB to 550MHz on P5B-Deluxe

[bugeyes]

I dont get it .You have retail 6600 and you can change multy downwards to 7? Didnt know its possible i thought only ES have lower multy option.

Only with the later bioses, I think it has to do with Intels speedstep tech (cool-n-quiet)

[dinos22]

Only with the later bioses, I think it has to do with Intels speedstep tech (cool-n-quiet)

what was your board max withprevious bioses

you on E6600 yeah?

[bugeyes]

what was your board max withprevious bioses

you on E6600 yeah?

bios 0405 multies locked FSB to 500MHz
bios 0507 multies unlocked FSB to 650MHz ( bit of a joke that..505 is the max I could get unmodded)

[dinos22]

i'm asking you how much your max OC changed from first bioses to the latest ones

[bugeyes]

i'm asking you how much your max OC changed from first bioses to the latest ones

Max OC for that retail E6600 has not changed from 3.6GHz using later bioses, however when approaching 500MHz FSB max cpu clocks do reduce, as to what level I have not determinded.

[775911]

Can I see a pic of the motherboard after the mod is done

[dinos22]

Max OC for that retail E6600 has not changed from 3.6GHz using later bioses, however when approaching 500MHz FSB max cpu clocks do reduce, as to what level I have not determinded.

max FSB OC i should say sorry

[bugeyes]

max FSB OC i should say sorry

shipping bios I could max out at 400MHz, 0405 I could max out at 400MHz (limited by locked multies), 0507 will only give me 505MHz though I'm sure it will go higher if I get rid of the N/B passive heatpipe.

[Athens[2004]]

I change my order from ds4 to p5b-dlx . Nice thread - info

[ben ifin]

TAKE TWO

Hi AndreYang & tanghiro - re-posting as a few of us here are asking / awaiting this info

( i ) Can either of you please post a picture of the completed mod ?

( ii ) Can you please advise the highest FSB you can get when using
just 1.65v for the MCH ?

Many thx,
Ben.

[Moonraker™]

shipping bios I could max out at 400MHz, 0405 I could max out at 400MHz (limited by locked multies), 0507 will only give me 505MHz though I'm sure it will go higher if I get rid of the N/B passive heatpipe.

You reckon that the NB is that bad then?

I was thinking of replacing it with the TT Extreme Spirit II. and leaving the voltage heaty's on. Using silver as the compound. on both. Sawing the bar off in between them.

[dinos22]

shipping bios I could max out at 400MHz, 0405 I could max out at 400MHz (limited by locked multies), 0507 will only give me 505MHz though I'm sure it will go higher if I get rid of the N/B passive heatpipe.

yeah that's what i was getting at

hmmmmmmmmmmmmmm what to do now heheheh get an asus as well me thinks heh

[eva2000]

yeah that's what i was getting at

hmmmmmmmmmmmmmm what to do now heheheh get an asus as well me thinks heh

ah the sickness

[adfinni]

TAKE TWO

Hi AndreYang & tanghiro - re-posting as a few of us here are asking / awaiting this info

( i ) Can either of you please post a picture of the completed mod ?

( ii ) Can you please advise the highest FSB you can get when using
just 1.65v for the MCH ?

Many thx,
Ben.

Could you plz post the info requested above as im about to order two of these bords for new setups paired with E6400's and TEAMgroup DDR2 5300 kits, but still don't see how exactly to do the mod.

-What voltage for MCH did you guys use to get 550fsb ?
- could you please post pics of a more general (zoomed) out view, as the only pics i have seen show a wire or two attached to the resistor, not an overall view of the completed circuit?

Here is my elite image manipulation for 1.65V , is it right at all ?



My soldering skills are good but im not sure exactly what to do yet, and i think some other people need help understanding too.

Thanks very much lads

[SynGroW]

Could you plz post the info requested above as im about to order two of these bords for new setups paired with E6400's and TEAMgroup DDR2 5300 kits, but still don't see how exactly to do the mod.

-What voltage for MCH did you guys use to get 550fsb ?
- could you please post pics of a more general (zoomed) out view, as the only pics i have seen show a wire or two attached to the resistor, not an overall view of the completed circuit?

Here is my elite image manipulation for 1.65V , is it right at all ?

http://img413.imageshack.us/img413/4527/modil4.jpg

My soldering skills are good but im not sure exactly what to do yet, and i think some other people need help understanding too.

Thanks very much lads

CAL930 posted another way to mod the vMCH in a thread about the Asus P5B Deluxe


20kΩ～50kΩVR

Maybe easier to do this version of the mod

click to view CAL930's post

[jmax_oc]

Test Configuration:
Memory: CORSAIR CMX1024-9600C5

How do you get such memory ?

Can we have some informations about it ?

[bugeyes]

You reckon that the NB is that bad then?

I was thinking of replacing it with the TT Extreme Spirit II. and leaving the voltage heaty's on. Using silver as the compound. on both. Sawing the bar off in between them.

No I don't think it's bad at all... 266MHz out to 500MHz thats pretty good, I'm just trying to make the point that as I got to 500MHz @ 1.45v to the N/B any more volts gained nil mhz, that could and I stress the word could mean heat is a factor.

I wouldn't be sawing anything in half, particularly your mobos heatpipe, leave it be, but if your a compulsive tinkerer, remove it and replace with whatever, buy some ram sinks for power mosfets.

[AndreYang]

another VMCH modded.

[ben ifin]

Hi AndreYang

How high a FSB were you getting with just 1.65v in the MCH ?

Ben

[adfinni]

I presume this resistor is suitable:

http://www.maplin.co.uk/Module.aspx?...=SEO&U=strat15

Then solder the relevent pins (leaving the top one unconnected ?)

Once installed do you incease its resistance to max then turn it down until the voltage measured goes up to 1.65V ????

thanks

[OC_Windforce]

Hi AndreYang

P5B-Deluxe
The ClockGen Tools use it is possible.?

[jmax_oc]

Test Configuration:
Memory: CORSAIR CMX1024-9600C5

How do you get such memory ?

Can we have some informations about it ?

Is it possible to know how to you get such sample memory ?

[775911]

Does this board allow for high ratios like 4:3 ?

[AndreYang]

Hi AndreYang

P5B-Deluxe
The ClockGen Tools use it is possible.?

P5B Deluxe didn't support ClcokGen and setFSB yet.

[AndreYang]

Does this board allow for high ratios like 4:3 ?

P5B Deluxe 4:5 has some problems. You need to use 1:1 or 2:3.