Insulation Intel Bad Axe Rev 3.04 & Wb for chipset Modd

[vapb400]

woot! thanks alot, im gonna be needing it soon

[BarboneNet]

I have edit the first post!

I have upload the first package of image.......but i need help for explain them in english

[BarboneNet]

due

[Dumo]

Heres mine...

[mesyn191]

where did you get those hold downs for the NB block? Did you make them yourself?

[BarboneNet]

where did you get those hold downs for the NB block? Did you make them yourself?

Danger den WB.....75euro or 80US Dollars with shipment

[Langley]

VERY NICE WORK MAN!!!!!!!!
The best insulation clean job and great hand here!!!!

BEL LAVORO BOTTANAZZZAAA!!!!

[BarboneNet]

VERY NICE WORK MAN!!!!!!!!
The best insulation clean job and great hand here!!!!

BEL LAVORO BOTTANAZZZAAA!!!!

Thanks LORD

Grazie cacapalle

[outcast623]

VERY nice! see you did another update of the first post.

what are the different thickneses of neoprene you are using? do either of them have sticky backs to them?

[BarboneNet]

VERY nice! see you did another update of the first post.

what are the different thickneses of neoprene you are using? do either of them have sticky backs to them?

thanks Neoprene is 10mm(on the mobo), and 5mm(on top).....they both have a stickys on the back!

In few days, i post the discriptions of the photos.......i have some problem with english

P.S. on the mobo, you can use neoprene without sticky, or you can put the sticky on the otherside....the insulation works fine the same...and the mobo is clean

[BarboneNet]

This is my phase in action with Celeron D326 !!

The insulation works very fine....but the sensor of CPU is in eccess about +5°/+10°

[kayl]

Nice job there. one little hint dont let mobo get to cold before booting other wise get condensation troubles and system not boot.
And dont clamp the block too tight or wont boot again.

[LukeXE]

Nice

I must say, BarboneNet...your avatar is...uh, very nice !

[BarboneNet]

Nice job there. one little hint dont let mobo get to cold before booting other wise get condensation troubles and system not boot.
And dont clap the block too tight or wont boot again.

i comfirm your affirmation: If you prestart the phase change for 30minutes(or more) before start the mobo....you can have condensation!!!

But if you start your mobo, after only 5-25minutes of phase prestart......no problem

Nice

I must say, BarboneNet...your avatar is...uh, very nice !

[Nosfer@tu]

Heres mine...

Dumo, Se you also have an LS, I also have the same Nb cooler, like it alot
had to use a file and "shave" som of the grip down, so it had better grib to the nb "holder's"

Why have you used extra neopren around the socket? And alo on the NB?
The NB neoporen is just for stability or do you use chilled water?

Also it looks like grease around the socket? Why use that when you have such a good mounting mecanism?

Regarding the Retension mechanism, I dont remove it, I just fill it up along the eges so I have lees air to create condensation in case of a Mis happ.

[Patriote]

Pics arent working anymore!

[BarboneNet]

Pics arent working anymore!

What????

I use this insulation on p5w64-ws......but now i mod the meccanics of retention CPU!!!

[easyrider]

So no Dielectric grease was used either in the socket or around the socket?

Or back of the mobo etc...?

Thanks


Reason I ask is I'm going to do phase and am new to it.

[Raja@ASUS]

long term fixes are always better off with grease, regardless..

for a first time phase user, the need for using dialectric grease is virtually mandatory..

If you search the forum here you'll find people with a couple of conroe's that have corroded pads..

regards
raja

[Brettbeck]

Nice mod! Looks really clean too .

[jabski]

So no Dielectric grease was used either in the socket or around the socket?

Or back of the mobo etc...?

Thanks


Reason I ask is I'm going to do phase and am new to it.

this thread should help you easyrider.

Nice work BarboneNet

[easyrider]

this thread should help you easyrider.

Nice work BarboneNet

Thanks mate for the link.