NF3/NF4 & TCCD - Highest stable clocks - REPORT IN !!!

[masni]

i got a pair of adata vitesta ddr600 (2x256mb) with samsung tccd...

it is interesting that this memory loves high vdimm, in order to pass 32m sp mem needed 3.1V vdimm...

dfi ultra-d & venice 3000+

<a href="http://imageshack.us"><img src="http://img482.imageshack.us/img482/6550/340httsuperpi32mb1t2lm.jpg" border="0" width="1024" alt="Image Hosted by ImageShack.us" /></a>

my cpu wasn't that good so i lowered multi x8...

[bachus_anonym]

I guess I need to remind some of you guys about the rules for this thread - http://www.xtremesystems.org/forums/...&postcount=298. Can those of you I'm talking to stick to posting ONLY, I repeat ONLY screenshots with 32M results, please? This way thread is a lot easier to browse. If you have a problem or need any guidance with your memory overclocking, start a new thread in Xtreme Bandwidth If neccesary (after searching the forums for similar problems and solutions, of course )

Thread has been cleaned up again

[bachus_anonym]

*** Thread updated ***

Congratulations to The_NamelessOne on a very nice, new WR @ 330MHz 8-4-4-2.5-1T

Thans for dropping by and sorry for a tiny delay Keep torturing those TCCDs! Keep me busy, guys!

[Malph]

DFI Ultra-D, OCZ PC4800 EL

[szukalski]

Geil Ultra-X and One S @ 273MHz @ 2.5-3-3-5-7-14-2-2-1-2-2T @ 2.6v :

[meateater]

ocz plat 3200 rev 2 @ ddr 600 2.7v 2.5-4-4-8 1T
2x512

[funkflix]

A bit TCCD action from me, nothing impressiv, but i'm new to this game.

funkflix - 305x10=2520MHz DDR610 @ 5-3-4-2.5-1T - DFI Ultra-D (NF4 ) - Opteron 146 - GeIL ONE Series PC3200

[dogsx2]

These are turning out to be pretty good memory.



Tweake shot.


2.9 bios just for benching. Sticks are rated 2.7-2.9. It's no different then runnig 3.6+ in UTT or BH-5 while benching. I never run wide open 24/7.
BTW, SG is like horseshoes, just close, not exact.

[Major]

These are turning out to be pretty good memory.

Hey your not suppose to show me up !!!

Looking good, the best I was able to do with them was 310mhz and that was with pretty loose settings.

[dinos22]

it's a shame the entries don't have MBM5 or Smartguardian shot in them as a requirement as well

i've got a pair of PC4800FF sticks and i'll do some more benching before i submit final :banana::banana::banana::banana:s but it will be around 310MHz 2.5-4-3-7 1T mark......need to tweak it a little moreheheheh

i started playing with them last night after some good advice from eva2000 over at www.i4memory.com

Opteron 146 CABYE 0540FPBW Air-cooled
DFI NF4 UltraD 623 bios
2x512MB G.Skill PC4800FF



[EDIT]

ok max stable so far is

TRCD=4


dinos22 - 310x10=3102MHz DDR620 @ 7-3-4-2.5-1T - DFI Ultra-D (NF4 Ultra) - A64 Venus - GSkill PC4800FF


SuperPI 32M 310MHz (DDR600) 2.5-4-3-7 1T @2.9v

[dogsx2]

Hey your not suppose to show me up !!!

Looking good, the best I was able to do with them was 310mhz and that was with pretty loose settings.

Thanks, your skills are much greater then mine, you must not have been trying hard. This 170 I'm messing with has a really good memory controller on it. To get into the top ten with a 4 TRCD a guys got to be at 320 and up.

[-Wolverine-]

Here R my GeIL OneS TCCD @ 312 2,5-4-3-7 2.8v
I'll try to squeeze out something more soon

[865pe]

• Opteron146@2880
• G.Skill Fx 3200 2x512
• 2.5-4-3-6 1T
• 320@DDR640 2.8v Not: Have 4 Lops screenshots

[bachus_anonym]

*** Thread updated and some unneccessary posts removed ***

Bring it on, guys! Is that all you got?

[njkid32]

Here is my opty 0530APMW with my Gskill FC's

[msimax]

this is with my new ultra-d and patriot ddr 600 kit.. im new to nf4 and suprised, these only did 285 with my neo2plat board. im trying to get them stable above 310@2.5-3-3-? Any suggesting or help appreciated thanx

[joek71]

DFI LANPARTY UT nF4 SLI-DR Expert (12-7-05)

AMD OPTERON 175 (CCBWED546XPMW) 250*11=2750 w/ CL-P0114 / SUNON KD1212PTB1-6A 120mm

Patriot Dual Channel XBL 2x512MB PDC1G3200+XBLK (tccd)

EVGA 7800GTX 256MB, PCI-E

2 Western Digital Raptors WD740GD 74GB 10,000 RPM

LITE-ON LTR-24102B
PLEXTOR DVDR PX-708A
SONY DVD-ROM DDU1621

PC Power & Cooling 510 SLI-PFC ATX12V 510W Power Supply 90 - 264V UL/ ULC/ TUV/ CE-Retail

==========

Genie BIOS Settings:

FSB Bus Frequency - 250
LDT/FSB Frequency Ratio - 4
CPU/FSB Frequency Ratio - 11
PCI eXpress Frequency - 100Mhz

CPU VID StartUp Value - STARTUP

CPU VID Control - 1.550v
CPU VID Special Control - Above VID * 102.4%
LDT Voltage Control - 1.40v
Chip Set Voltage Control - 1.68v
DRAM Voltage Control - 2.92

DRAM Configuration Settings:

DRAM Frequency Set - 200=RAM/FSB:1/1
Command Per Clock (CPC) - Enable
CAS Latency Control (Tcl) - 2.5
RAS# to CAS# delay (Trcd) - 04 Bus Clocks
Min RAS# active time (Tras) - 08 Bus Clocks
Row precharge time (Trp) - 04 Bus Clocks
Row Cycle time (Trc) - 12 Bus Clocks
Row refresh cyc time (Trfc) - 16 Bus Clocks
Row to Row delay (Trrd) - 03 Bus Clocks
Write recovery time (Twr) - 03 Bus Clocks
Write to Read delay (Twtr) - 01 Bus Clocks
Read to Write delay (Trwt) - 02 Bus Clocks
Refresh Period (Tref) - 3120 Cycles
Write CAS Latency (Twcl) - AUTO
DRAM Bank Interleave - Enabled

DQS Skew Control - Increase
DQS Skew Value - 150
DRAM Drive Strength - Level 7
DRAM Data Drive Strength - Level 1(Reduce 50%)
Max Async Latency - 7
DRAM Response Time - Fast
Read Preamble Time - 5
IdleCycle Limit - AUTO
Dynamic Counter - Disable
R/W Queue Bypass - 8 x
Bypass Max - 05 x
32 Byte Granularity - ENABLE(4 Bursts)


==========

Prime95 + 3dMark2003:
http://joek71ny.tripod.com/images/mbm.jpg

3DMark2003:
http://joek71ny.tripod.com/images/prime95_3dmark_03.jpg

3DMark2005:
http://joek71ny.tripod.com/images/3dmark_05.jpg

3DMark2006:
http://joek71ny.tripod.com/images/3dmark_06.jpg

EVEREST 2006:
http://joek71ny.tripod.com/images/ev...emory_read.jpg

http://joek71ny.tripod.com/images/ev...ry_latency.jpg

http://joek71ny.tripod.com/images/ev...mory_write.jpg

==========

short description:
250*11 @ 2750Mhz, 1/1, 1.550v + 102%
2.5-4-8-4 @ 2.92vdimm

[Nebulous]

Here's the best i can do with my relic:

1GB kit Gskill PC4400LE @ 301 with 2.5-4-4-7 & 2.8v. Not too shabby

[ixtapalapaquetl]

DFI Venus
4x512 G.Skill FF's
Opteron 148 CABNE 0528

9x302MHz and sloppy timings:

[uOpt]

Looks like my CABNE is not dead after all

• Geil One TCCD 2x 256 MB at 3.0 V.
• CABNE from sig at 1.45 V.
• DFI NF4 SLI-DR BIOS 623-3.
• OCZ Powerstream 520W.
• Watercooling, storm block, direct high-RPM fan on RAM.

Screenshots and real-world photos from in between that run, plus rig photo:
http://www.cons.org/tmp/oc-screens/o...-superpi32m_1/

[i found nemo]

hey guys after a bunch of messin' around i got my ram to run desireably, imo it's a very decent time for 2300 some odd mhz

plz love my tccd

2.8 v's 2.5-3-3-5. i'm sure i can do more, i've seen 290 @ 3-4-4-8 2.8v's but only 1 stick at a time and am unsure if it's stable.

anyways here's my max clock for dual sticks 2*512

trtw and the other two 18 settings seen in a64 tweaker helped my by 100+ mb/s so it'll help even MORE for dual channel guys. high preamble and mal settings helped me gain stability at a tinch of performance cost

[zungkono]

This is my max mem, GSkill pc3200GBFX @316MHz 2.5-4-3-7 1T 2.8v
200-E-2.5-4-3-7-17-19-2-3-2-3-3120-1-E-A-0-5-1-9-Fast-6.5-16-E-16-7-D
DFI Ultra-D R.AD0 + Opteron 148
Bios 704-2BTA

[Super Nade]

PDP Patriot PC4800 XBLK (got this set for ~$100)

PDP Patriot XBLK PC4800 TCCD, DFI-NF4 SLI-DR (Non-Expert)
-----------------------------------------------------------------------

Note* The person I bought this board off of said it was Angry Games' primary testing board. It scales very well with HTT, 372 MHz to be precise. However, I have no reason to believe this excellent set of PC4800 RAM would not do well with my older Ultra-D.


Last Updated:March 22, 2006
Motherboard: Lanparty NF4 SLI DR Non-Expert
Bios: 704BTA (with dangerous VCore options removed)
CPU: Opteron 165 DC
VC: 2 x XFX 6800GS, 81.98 WHQL Drivers
OS: Windows XP Pro w/SP2
Ram: PDP Patriot XBLK PC4800 (TCCD) In the #2 and #4 (Orange) Dimm slots
Chipset Drivers: Revision 6.70 (w/out IDE Drivers)

DRAM Timings:

• Ram Multi DDR400 1:1
  CPC ENABLED
  Tcl 2.5
  Trcd 3
  Tras 08
  Trp 03
  Trc 11
  Trfc 22
  Trrd 03
  Twr 03
  Twtr 02
  Trwt 03
  Tref 3072 200MHz, 3.9 us
  Twcl 01
  Bank Inter EN
  Dynamic Skew Control Decrease
  Skew Value 255
  DRAM Drive Strength 8
  DRAM Data Drive Strength 1
  Max Async 8 ns
  Read Preamble 5 ns
  Idle Cycle 128
  Dynamic Counter DIS
  R/W Que Bypass 16x
  Bypass MAx 7x
  32 Bit Gran DIS

Voltages etc:

• HTT 300
  LDT 2.5 x
  Cpu Multi 9 x
  PCE-I 100
  Vcore Startup 1.500
  Vcore 1.475
  Vcore Special 104.8%
  LDT V 1.4
  Chipset V 1.6
  Vdimm 2.9 V (2.83 V works as well and I'm using this after burn in)

[uOpt]

These Geil One 2x 256 MB TCCD were the best buy ever

There is no end to the room in there.

Now drive strength 7:1, new max async latency, 2.9 Volts:




Required more screenshots from in between:
http://www.cons.org/tmp/oc-screens/g...e-v15_clock_1/

[bachus_anonym]

*** UPDATED ***
It looks like the pace got a bit slower Anyone else wanted to contribute, please?