"ASUS P5Q Deluxe discussion".

Printable View

Show 100 post(s) from this thread on one page

06-11-2008, 08:09 PM
BulldogPO

Can somebody post good P5Q3 bios settings for around 500MHz FSB for wolfdale?
Mainly voltages and GTL settings.

I´m strugling with this board.
06-11-2008, 08:45 PM
Leeghoofd

Quote:

Originally Posted by STEvil

'fet sinks usually do more harm than good due to poor application and board warping due to poor heatsink installation methods.

P5Q Dlx has backplates on the mosfets heatsinks, no warping anymore, Asus finally took care of their bad mounts... Tried with the stock heatsinks and now back on water... board is as rigid as can be :up:

I'll check Mosfet Temp Looser777 for ya (will switch off my 25 cm sidepanel fan)
06-11-2008, 11:10 PM
The Nemesis

Board is now $199 with free ups 3Day @egg.:D
06-12-2008, 01:16 AM
jozzy

i can get only 570 for now..

http://valid.x86-secret.com/cache/banner/374305.png

is there any ram divider works better rather than the 5:6 ? :shrug:
06-12-2008, 01:31 AM
jVIDIA

The screws of the mosfets heatsinks come off easilly ?
06-12-2008, 02:43 AM
aussie-revhead

Hi guys , most of you are multiple mobo owners , do you prefer this to a 790i ? I have only had mine a week and am already looking at making a move as this baby looks like its got the right stuff .

:up:

Quote:

Originally Posted by NIZ

Someone hurry up & test q9450/9550 with this board pls. Want to see if the 440/450fsb wall is gone from the old P35 boards.

Niz - did you find your info ? There are a few in this large thread but its looking good mate .

.
06-12-2008, 03:24 AM
@rne

I played another time, this is max under air for this cpu:
http://valid.x86-secret.com/show_oc.php?id=374337
06-12-2008, 03:42 AM
marcin255

PL its ??

Performance Level
06-12-2008, 03:47 AM
Chri$ch

ohhh... new toys arrived :D

http://www.abload.de/img/dscf7457a32.jpg
06-12-2008, 03:50 AM
BigJoe

@Chri$ch
It's great stuf there mate :)
06-12-2008, 04:38 AM
minaelromany

I will get the P5Q DLX as soon as it is released here in Egypt but I will have to sell my Foxconn MARS
06-12-2008, 05:21 AM
jVIDIA

No new bioses ? :D
06-12-2008, 05:34 AM
_sindre_

Quote:

Originally Posted by Chri$ch

now i played a little bit with the performance level and come to 615FSB :D

i can boot 600FSB out of the bios :)

What bios settings did you use here? I've used serveral hours to tweak the first bios I've resived form asus, and have no big intrerrest in starting all over again. :rolleyes:
06-12-2008, 05:55 AM
GAR

I just ordered the P5Q3 deluxe from newegg, will be here soon......ill see how it does with my Q9450 and report back.
06-12-2008, 06:24 AM
pmp

If someone with P5Q series could have a look here and compare how P5Q series looks like compared to M2F, it would be nice! :)
http://www.xtremesystems.org/forums/...9&postcount=36
06-12-2008, 06:31 AM
gugle

and the P5Q-E ?
06-12-2008, 07:20 AM
diablos

sorry guys,
what are the differences between p5q pro deluxe and premium?

thanks
06-12-2008, 07:23 AM
gugle

Quote:

Originally Posted by diablos

sorry guys,
what are the differences between p5q pro deluxe and premium?

thanks

http://www.xtremesystems.org/forums/...0&postcount=39

http://news.mydrivers.com/img/20080508/12045303.png
06-12-2008, 01:41 PM
Leeghoofd

Got my Precious Gskills in the rig doing some tests at 1200mhz ram to determine the performance level

With 400FSB I can get 6 performance level

http://users.pandora.be/OAP/P5QDlx/400-1200.JPG

Will do 500FSB in a bit

Validation already :) Damn I love this board :up:

http://users.pandora.be/OAP/P5QDlx/4500-1200.JPG

With 500FSB Performance level 8 with ram at 1200Mhz

http://users.pandora.be/OAP/P5QDlx/500-1200.jpg
06-12-2008, 02:18 PM
]siNNer[

I see the vcore increase from 400x10 to 500x8 is that really required or you set it "just in case"?

Anyway, by this results we see that the P45 is not that bad as some people said and low PL is doable :D

I'll have mine by tomorrow so keep us up to date with results and bios settings when possible. :up:
06-12-2008, 02:22 PM
Leeghoofd

Quote:

Originally Posted by ]siNNer[

I see the vcore increase from 400x10 to 500x8 is that really required or you set it "just in case"?

1.32 (LLC enabled) made the PC shutdown when I ran prime... so I went straight to 1.4 to get the screenshot... think it might do it at 1.35ish level... :shrug:
06-12-2008, 03:12 PM
STaRGaZeR

Leeg can you post NB, PLL etc. voltages for 500FSB Performance level 8 with ram at 1200Mhz?
06-12-2008, 05:08 PM
TouGe

So far it has been interesting.

I was able to hit 8x450FSB using 2x1GB 5-5-5-15-3-25 PL7 & 400FSB Strap but was not able to keep it prime stable. The highest FSB I was able to keep stable w/ the same timings and 2 sticks was 440 but for 24/7 this is what I stuck with:

PHP Code:

JumperFree Configuration Settings AI Overclock tuner: Manual CPU Ratio Setting: 8.5 FSB Strap to North Bridge: 400 FSB Frequency: 425 PCI-E Frequency: 105 DRAM Frequency: 1133 DRAM CLK Skew on Channel A1: AUTO DRAM CLK Skew on Channel A2: AUTO DRAM CLK Skew on Channel B1: AUTO DRAM CLK Skew on Channel B2: AUTO DRAM Timing Control: Manual 1st Information : CAS# Latency: 5 DRAM RAS# to CAS# Delay: 5 DRAM RAS# Precharge: 5 DRAM RAS# Activate to Precharge: 15 RAS# to RAS# Delay : 3 Row Refresh Cycle Time: 25 Write Recovery Time: 6 Read to Precharge Time: 3 2nd Information : READ to WRITE Delay (S/D): 8 Write to Read Delay (S): 3 WRITE to READ Delay (D): 5 READ to READ Delay (S): 4 READ to READ Delay (D): 6 WRITE to WRITE Delay (S): 4 WRITE to WRITE Delay (D): 6 3rd Information : WRITE to PRE Delay: 11 READ to PRE Delay: 5 PRE to PRE Delay: 1 ALL PRE to ACT Delay: 4 ALL PRE to REF Delay: 4 DRAM Static Read Control: Enabled DRAM Read Training: AUTO MEM. OC Charger: AUTO AI Clock Twister: Strong AI Transaction Booster: Manual Common Performance Level 7 Pull-In of CHA PH1: DISABLED Pull-In of CHA PH2: DISABLED Pull-In of CHA PH3: DISABLED Pull-In of CHA PH4: DISABLED Pull-In of CHB PH1: DISABLED Pull-In of CHB PH2: DISABLED Pull-In of CHB PH3: DISABLED Pull-In of CHB PH4: DISABLED CPU Voltage: 1.3625V (1.28V under load) CPU GTL Voltage Reference (0/2): AUTO CPU GTL Voltage Reference (1/3): AUTO CPU PLL Voltage: 1.50V FSB Termination Voltage: 1.20V DRAM Voltage: 2.14V NB Voltage: 1.28V NB GTL Reference: AUTO SBridge Voltage: 1.10V PCIE SATA Voltage: 1.50V Load Line Calibration: Disabled CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU Clock Skew : Auto NB Clock Skew : Auto Advance CPU Settings CPU Ratio Setting: Manual CPU VID: Default C1E Suppport: Disabled Max CPUID Value Limit: Disabled Intel® Virtualization Tech: Disabled Vanderpool Technology: Disabled CPU TM Function: Disabled Execute Disable Bit: Disabled

I there a pencil mod for Vcore on this board? With Loadline Disabled there's a ~.08V difference between Idle and Load. I would like to shoot for 9x425MHz but it would take >1.4V for me to do it w/ LLC disabled. It would be nice to cut the difference in half since I don't like enabling LLC, especially above 1.3V.

As for 4x1GB sticks I was unable to do anything worth while. It took PL10 just to boot into windows @ a 400FSB Strap & 1066MHz using 5-5-5-15-3-42 timings but errored out of Prime w/in 3 minutes.

Can someone tell me a functional nbv range on this board w/ 4 sticks of RAM?

I'm currently testing my 2x2GB OCZ FlexII's. They seem a little more well behaved than 4x1GB Cell Shocks.

PHP Code:

JumperFree Configuration Settings AI Overclock tuner: Manual CPU Ratio Setting: 7.5 FSB Strap to North Bridge: 266 FSB Frequency: 400 PCI-E Frequency: 105 DRAM Frequency: 1003 DRAM CLK Skew on Channel A1: AUTO DRAM CLK Skew on Channel A2: AUTO DRAM CLK Skew on Channel B1: AUTO DRAM CLK Skew on Channel B2: AUTO DRAM Timing Control: Manual 1st Information : CAS# Latency: 5 DRAM RAS# to CAS# Delay: 5 DRAM RAS# Precharge: 5 DRAM RAS# Activate to Precharge: 15 RAS# to RAS# Delay : 3 Row Refresh Cycle Time: 55 Write Recovery Time: 6 Read to Precharge Time: 3 2nd Information : READ to WRITE Delay (S/D): 8 Write to Read Delay (S): 3 WRITE to READ Delay (D): 5 READ to READ Delay (S): 4 READ to READ Delay (D): 6 WRITE to WRITE Delay (S): 4 WRITE to WRITE Delay (D): 6 3rd Information : WRITE to PRE Delay: 14 READ to PRE Delay: 5 PRE to PRE Delay: 1 ALL PRE to ACT Delay: 5 ALL PRE to REF Delay: 5 DRAM Static Read Control: AUTO DRAM Read Training: AUTO MEM. OC Charger: AUTO AI Clock Twister: AUTO AI Transaction Booster: Manual Common Performance Level 7 Pull-In of CHA PH1: DISABLED Pull-In of CHA PH2: DISABLED Pull-In of CHA PH3: DISABLED Pull-In of CHA PH4: DISABLED Pull-In of CHB PH1: DISABLED Pull-In of CHB PH2: DISABLED Pull-In of CHB PH3: DISABLED Pull-In of CHB PH4: DISABLED CPU Voltage: AUTO CPU GTL Voltage Reference (0/2): AUTO CPU GTL Voltage Reference (1/3): AUTO CPU PLL Voltage: 1.50V FSB Termination Voltage: 1.20V DRAM Voltage: 1.94V NB Voltage: 1.24V NB GTL Reference: AUTO SBridge Voltage: 1.10V PCIE SATA Voltage: 1.50V Load Line Calibration: Disabled CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU Clock Skew : AUTO NB Clock Skew : AUTO Advance CPU Settings CPU Ratio Setting: Manual CPU VID: Default C1E Suppport: Disabled Max CPUID Value Limit: Disabled Intel® Virtualization Tech: Disabled Vanderpool Technology: Disabled CPU TM Function: Disabled Execute Disable Bit: Disabled

I was unable to get them to run on the 400 Strap which was the case when using them on my DFI x48 board so I am currently using the 266 Strap. I have a feeling that I will need to delve into DRAM Clock Skew if I want to reach anything close to 1066MHz.

If anyone has any tips on how to run 4x1GB sticks at a decent performance level on this board let me know.
06-12-2008, 05:28 PM
R@ptor =]]

There wasn't an option to delete the vdroop?
What is the function of Load Line Calibration??
06-12-2008, 05:36 PM
TouGe

Quote:

Originally Posted by R@ptor =]]

There wasn't an option to delete the vdroop?
What is the function of Load Line Calibration??

Are you referring to my post? If so, LLC enabled will eliminate vdroop. I'm not looking to eliminate all the vdroop but just cut it in half. This is what I did on my Maximus Formula board. If I enable vdroop now my vcore actually increases slightly on load.

Show 100 post(s) from this thread on one page