i'm using 1.42v 24/7 on nb with thermalright hr-05 ifx no fan hottest i saw it was 38cQuote:
Originally Posted by mad_skills
i'm using 1.42v 24/7 on nb with thermalright hr-05 ifx no fan hottest i saw it was 38cQuote:
Originally Posted by mad_skills
i finally broke 12k:):):)
zsamz_ - thats really great, congrats & respect !!
woot!!! great to see this board has still much to offer!
Has anyone done 500MHz on Q6600 on this mobo by any chance?
Here:http://xs222.xs.to/xs222/07506/FSB500SP1Mmem600.gifQuote:
Originally Posted by mad_skills
My mistake, what i meant was prime stable 500MHz for few hours, and some NB, VTT and GTL settings if possible. :wave:
500FSB Prime is in early pages of this thread, I have done 484FSB Prime stable with Q6600 (NB 1.61, VTT 1.60, GTL Disabled), I don't have screens since my RAID0 failure but I think it somewhere here on XS :D. The board is capable of 500FSB, but you need a cherrypick CPU.Quote:
Originally Posted by mad_skills
Prime stable at 500+fsb with a quad is a very tall order on any mobo. I hav'nt seen anyone post an 8hrs Orthos/Prime run as proof they have done it. Plenty of suicide shots, but no Prime proof. Running a dual core at 500+fsb is easy, i have run an E6600, two E8500's and my current E8600 all at 500fsb or over. In fact i've never run any of them under 500fsb.Quote:
Originally Posted by mad_skills
I know C2D is easy, have done it on my previous E6750 just want to try it on Q6600 as well.Quote:
Originally Posted by kitfit1
I know the board is capable, and the cpu is a really good one, i just wandered what possible settings i might need be using and since it's 52F (11C) here i thought i might try it. :)Quote:
Originally Posted by nfm
i miss my DFI P35 board... :( this P45 JR is quite confusing for me :(
If going P45 why didn't you get Dark LanParty man?
coz was just planning to use this for a HTPC setup for my brother...but since it's DFI, i wanna so TWEAK itQuote:
Originally Posted by mad_skills
great mobo.. this thing runs dead cold even @ full load
the only limit: vtt i need way more than 1.45/more than just 1.6
do the JP10/J16 jumpers have anything to do with vtt? is there a vtt mod posted?
thanks
Why would you need so much vtt?:confused:
lol why? cause if id have up to 2vtt or more available @ bios id be able to run my q9650 stable @ 5+ghz :D
http://valid.x86-secret.com/show_oc.php?id=423042
I bought an LT P35 T2R cheap and received it today, and promptly installed my E6300+Tuniq 120 for testing. So far, at 400FSB with the 2:3 divider on 266 strap, I can only seem to get my Ballistix 8500 kit stable. None of my other D9Gxx kits can pass MemTest. I'm wondering if I'm doing something wrong, or what...
dfi+d9gkx=:horse:Quote:
Originally Posted by Shiranui Gen-An
try 3-3-3-8 800-840 mhz 2.24v
hehehe funny gif... but not ALL the time true...Quote:
Originally Posted by zsamz_
old pic...
http://i116.photobucket.com/albums/o...z2GB-Prime.jpg
CPU-Z
http://i116.photobucket.com/albums/o...DR2RAMList.jpg
& yup, under the hood it says D9GKX :D
I never figured what these jumpers are for. I attempted to increase VTT over 1.6v in the past but ended up modding the vNB (controller between IDE and SATA ports). You could try asking onepagebook over the ocxtreme, he has direct contact with engineer of this board.Quote:
Originally Posted by NapalmV5
i can't do over 1150 with any of my 4 sets of d9gkx
but my 2x2 gskills pc2-9600 broke 12k:D
i can go higher but i dont wanna break 2.1v:p:
No way man, I got PC2-8800 and they crapped out at 525Mhz, didn't even reach rated 550Mhz.
damn send it backQuote:
Originally Posted by nfm
even my redline cn do 550+ withought breakin a sweat
tHat's hot $hit. Make cold and try 10x
i gonna have to wait till it gets cold to do 10xQuote:
Originally Posted by mrcape
i need lots of juice to go past 5.0
ahh onepagebook/oscar.. thanks nfmQuote:
Originally Posted by nfm
I didn't actually mean just GKX, I used D9Gxx as a generic prefix for all the stuff (GMH, GKX, GCT). It seems to choke on a lot of my GMH surprisingly (Dominator 6400C3 and 10000C5, Geil 9280 CAS4, OCZ Reaper 8500). The wierdest thing in the world with the Reapers is that if I put them in the green slots, only 1GB single-channel is seen by the system :confused: I put them in the yellow and it sees 2GB dual like it should. Both sticks work fine too, as well as both slots (any other 2x1GB kit in the green slots shows up fine). At any rate, I just would like to get 600MHz CAS5 working on more than my Ballistix before I even attempt anything higher like 650MHz CAS5 or high CAS4 clocks...Quote:
Originally Posted by zsamz_
Yea if you have the board in topic it's really picky about RAM. It didn't like my Cellshocks at all and gave less than mediocre results, around 530 - 550 cl5 and not even 4-5-5-10 1000 completely stable at 2.23v. xD Then I put them in my DS4 and the same ram did 4-4-4-8 1000 2.21v or 1200 5-5-5-10.
i got the x38 and the p35 n they both fussy on ramQuote:
Originally Posted by Shiranui Gen-An
i got so many kits n half of em no good on both boards gmh -gct-dkx
i just hope they will work on dfi p45 or i gonna go with another brand
gigbyte maybe? :rofl:Quote:
Originally Posted by zsamz_
:ROTF::ROTF: why are they giving free boards:ROTF::ROTF:Quote:
Originally Posted by emoners
i dont want it:down:
i'd buy an ecs before i buy anything that says gigabut
hi guys. searched google and these forums because i have a corrupt "cmos reloaded". i read it is not part of the cmos chip and dfi has a fix for it. wrote tech support and was informed to RMA the board because it is a problem with the cmos and they don't have a program for download to fix it. but when i put in a cmos from another board and did the long process of resetting i still get a corrupt "cmos reloaded" and it appears it's not the cmos chip. would any of you know how i could fix my "corrupt cmos reloaded"? i would appreciate it, thanks in advance. :confused:
You think it's an issue with subtimings?Quote:
Originally Posted by zsamz_
yes it can be + drive strength settingsQuote:
Originally Posted by Shiranui Gen-An
the board is like a 30 year old virgin:ROTF:
take out the battery for a night n hope it gets errasedQuote:
Originally Posted by the9093
the cmosreloaded in not part of the bois chip
its a different chip
can anyone upload the iso of the montherboard cd to rapidshare
i reistalled windows n now with sp3 i cant load the sound driver
thanks for the iso The9093
new Beta bios out today dated 9/19.
http://us.dfi.com.tw/Support/Downloa...FLAG=B&SITE=US
Not much listed, just updated CPU codes unless there are other change just not mentioned. Anyone care to give it a try and share your findings?
EDIT.. just flashed it myself. Not a single thing looks or acts different about it that I can tell. As long as stability at same settings isn't compromised, I'll leave it flashed. I guess the days of finding new goodies in the bioses are long over. Just maintenance now.
I'm sure that there are some differences that aren't listed. I am also very interested to know what they are.
BIOS 9/19
It appears that I can run More Aggressive on the memory (previously I couldn't), not sure how that happened. Vcore still gets overvolted (5/02, 5/21 same thing) by 0.025v and there's an ugly typo, I'm back to 3/17.
would you guys recommend the dfi lp lt p35 or the dfi lp ut p35 over an asus p5q pro ?
"no problemo seņor." :up:Quote:
Originally Posted by zsamz_
zsamz_
Can you do me a favor and boot your G.SKILLs at DDR1200 2:3 400FSB and tell your memory delays BIOS sets for you? Also what vNB and vDIMM. Thanks :).
70psQuote:
Originally Posted by nfm
245-647-957-712
245-712-957-645
all more aggressive
my nb is set @ 1.46 now as i'm only doing 505fsb
higher nb helps alot after 1200mhz
my set likes volts @ 2.0+ n i havent gone above 2.09
i've done 1260 100% stable 1.55v nb
after 505fsb need to bump pl level though
Have a little problem..the 2 bottom fan connectors near the southbridge stopped working. They have been fine for a few months. With that, the Diagnostic Led does not post any numbers and the board will not boot..I have cleared the CMOS..Any Ideas?
I have changed the Proc
I have changed the Ram
I have changed the Vid Card
New Power Supply
Lights on board work and all fans turn on except the bottom
This one is starting to bum me out...Help
SDGSERV,Im sending you a new "Rampage Formula" from the Egg:up:Quote:
Originally Posted by sdgserv
If someone here can help with the P35 DFI problem that would be GREAT
Arghhhhhhhhhhhhhhhhhhhhhhh
sorry if my problem is noobish but i really dont know what to do next
this board has been sitting around for about a week now so i borrowed a friend's e2140 to test this out since i cant wait for my new processor. at first it posted fine and i was able to get into the bios menu. first thing i did (and probably my biggest mistake?) was 'load optimized defaults' and about 10 seconds after that, it turned off then turned on again, with some weird debug led msg (it doesnt make any sense, its not a number or letter). after that i cleared the cmos (using ez switch) and turned it on again. same thing happened, it would turn off, and then turn on again without POSTing. it just stays like that with the fans turned out but without any display and the keyboard isnt working. i tried replacing the memory, removing the hdd & optical drive but the same thing happened, only sometimes it displays a different weird debug led msg. i'd really appreciate any help :(
edit: also, i didnt hear any beeps from the speaker...
What do the "weird debug led msg" say?
88? or a known error code?
try to
unplug the power cord and take the battery out for a few hours.
Clear the CMOS the old fashioned way. Also unplug the PSU wait a few minutes, that was happening a few time to me
@saint-francis weird as in it isnt an ASCII character that i know of :D
anyway what i did was cleared the cmos w/ jumpers & removed the battery overnight, & replace the ram and graphics card. after i turned it on today, it had this very same problem :
http://csd.dficlub.org/forum/showthr...52389&posted=1
so i cleared cmos again and now its posting fine, i am able to get into the bios.
cowie,sdgserv what you both said worked :D thanks a lot guys! hopefully i dont have any problems installing the OS lol. gonna try this again with the old graphics card to see if that was the problem (memory works fine with other rig).
its not posting again lol, this time theres no debug msg..just nothing at all. gonna try the same things over again later when i've got the time :)
update: finally got it all running (hopefully), seems like DIMM slots 1 & 2 were the problem (and my old graphics card)
Ok. I just set this PC up. Few questions. I used the 317 bios for the setup of the PC and tinkered with OC a bit before flashing the newest "official" bios.I am having problems OC the 502 bios. My question are this.
Which bios would OC best with this setup from experience? Also what should I use for the settings in the CPU Feature section of the bios. On the MSI P35 Platinum I had to disable most all of the settings and there was like an F4/F7 button that opened another hidden setting that was vital to OC on that board. Is there some hidden bios settings like that on this board? If so what button displays them?
Also with the CPU FSB jumpers, which would work best, by CPU, 266, or 333 setting? I had it on the 333 setting as the P35 Platinum automatically booted up any C2D as a 333fsb CPU. With this setup it just boots as a 266fsb CPU and I found I couldn't oc with that jumper setting hardly at all with 317 bios. I had to use the "By CPU" jumper setting.
Also which FSB/DDR2 strap settings would be best? 333/800 or 333/1066?
Voltage for this CPU are super low. Like 1.05v default. Seems crazy as the E6750 I used 6 months ago was like 1.2v. Where is a good starting place for 3.8ghz with TRUE-B?
Any tips for a DFI re-learner? Last DFI board I had was the LP NF4 and this is a lot different. LoL
Is there any custom Bios for this board? I know there were craploads on the NF4.
The bios you are running is the best one.Quote:
Originally Posted by AcydRaine
Don't use any jumpers, if you have moved them, set them back to default.Quote:
Originally Posted by AcydRaine
Niether of them to be honest. Set the divider to 1:1, which i think is 667/800 for your cpu.Quote:
Originally Posted by AcydRaine
Only you will know that in the long run because it's down to what Vcore you feel comfortable with. But a safe starting point would be 1.35Vcore. Leave CPU VID Control on auto and use CPU VID Special Add to increase Vcore.Quote:
Originally Posted by AcydRaine
Have a good read here and here.Quote:
Originally Posted by AcydRaine
No, nobody has written any custom bios's for these as yet. My guess is that they are far too complicated for most of the bios re-writers now days.Quote:
Originally Posted by AcydRaine
Thanks for the tips bro. I tweaked on it all day then went to work. I will read over those sites in the morning and hit it hard again. I know the CPu is strong as I have loaded windows at 4.2ghz. Just fails orthos within 5 seconds from 3.9 up.
Another thing I have gathered browsing through this thread. What is up with the GTL settings. They seem to make a huge impact in stability for people. What is a good place to start with those on a C2D?
With this mobo and a dual core you should'nt really need to touch the GTL settings until you get higher than 490fsb. Have a read of this thread. You can always ask the O/P for any specific help.
hi, did you guys have any problems when trying to insert 2 DIMMs? my pair of ram (corsair xms2 dhx) works only if i put one at at a time, but when i put both it wont even POST. is this just a ram timing/voltage issue or is it possible that my sticks arent fully compatible with this board when in dual channel?
did you try memtest?Quote:
Originally Posted by ninong
Check this link.Quote:
Originally Posted by ninong
Helped me a lot.
emoners: yep, both sticks passed 1 loop after i tried each, i'm gonna try an overnight run
tzorge thanks, i'll try to do that once i get this thing to turns on again heh
hi
i recently flashed my mobo
i would like to get a safe OC (again)... maybe to 3.2ghz?
can someone help me with the bios setting? (ESAU are u there?)
i just flashed it to the 2008/05/21
please i would appreciate some help asap
thx!
pS: Esau~ i flashed caz recently my rig would just restart out of nothing after this "snap" "elec shock" kind of noise...
it was annoying and my temperature were fine... as usual
so i flashed and lost all the settings... :(
Getting a Q6600 to 3.2 should be very easy. Just raise the FSB a little at a time until it fails OCCT. Then give it a little more juice. Nothing special. This board will take your quad to 3.2 in it's sleep. I know I can get to 3.1 on stock voltage so you wouldn't have to increase it much at all. Just raise the special add maybe 3-5 %.Quote:
Originally Posted by Chanana
having some issues with my board came back from deployment and now its not posting and the board is showing "25" someone remind me what the code relates to.
Glad you made it back. On my postcode sheet '25' shows 'reserved'. Go to the DFI forum; they can help you out.
http://csd.dficlub.org/forum/index.php
Post Code #25/Quote:
Originally Posted by =[PULSAR]=
is there a master list with all the boot codes for this board and what they all mean? THANKS!
http://www.phoenix.com/NR/rdonlyres/...0/postcode.pdfQuote:
Originally Posted by =[PULSAR]=
woot!! nice to see this board is still worth keeping. :)
yes it isQuote:
Originally Posted by fireice2
i went back to x38 to try and its only problems with e8600
x38 clocks my gskills 9600 better but it just cant run as good with e8600
i be back soon :rofl:
ARRRRRRRRRRRGH I'm so close to getting my E6300 running 500x7 on my LT P35 T2R! I found out I needed to bump up PLL to 1.95V so now the PC will at least boot and (sometimes) start to run Memtest, but inevitably Memtest will feeze up. I've tried my Team 1200 and Ballistix 8500 (D9GMH) kits on the 333/667 and 333/800 straps to no avail. I'm sure I simply need to adjust some little thing, but I've tried Vcore (1.42~1.55), NB volts (1.4~1.7V), Vdimm, everything I can think of! Any suggestions?
I think the answer to your problem is quite simple really, by shoving 1.95v of PLL through it you have wrecked the cpu's ability to hold any sort of FSB. Even a good chance now that it won't even run at stock.Quote:
Originally Posted by Shiranui Gen-An
Quote:
Originally Posted by Shiranui Gen-An
hight gtl % gonna help
you crazy to put so much pl volts i would never use more than 1.6
are you sure the board likes your team 1200?
i tested a set of dominators with it and my board just hated em needed 2.2v just to boot so i'm sure they are d9gkx
they goin back to the store soon
http://www.xtremesystems.org/Forums/...0&postcount=57
I wonder if eva2000s' CPUs can't hold a FSB now?
well that cpu eva was usin musta been a real dudQuote:
Originally Posted by Shiranui Gen-An
my e6850 maxed out @ 584fsb 1.6v pl n i didnt even try higher volts :rofl:
CPU PLL and SB Voltage on the DFI LT/UT are linked, and there is no option for 1.6V...
oops my confusion :rofl:Quote:
Originally Posted by Shiranui Gen-An
was vtt
Finally have my system built to the point where I can start to overclock. Now all I have to do is read through 5000 odd posts to glean as much wisdom as possible. This thread rocks, it is a small part of the reason I picked the lt p35-t2r in the first place. I am on air and am trying to get my cooling wired first. My Xigmatek HDT-S1283 seems to be doing the trick. 20 at idle and just over 40 at load via Guardian. However, Core Temp is showing my cores about 10 degrees higher than that. Is this normal? Also, my dominator's are rated for 2.1 volts but I had to set the voltage to 2.2 volts in bios for Guardian to show 2.12 volts. Isn't that a lot of drop?
This is my setup:
Intel E8200 with Xigmatek HDT-S1283 sitting on it
DFI UT P35 T2R
Crucial BallistiX PC8500 2*1gb 1066 cl5
GeForce 8800 GTS 320mb
Samsung T166 500Gb
Samsung Sata DWD drive
Antec NeoHE 430W
Hey guys, I have read alot of this topic, and succeeded to get my E8200 to be stable at 8 x 500, in normal use its rock solid and orthos ran couple hours without errors. But when I try to play NFS Pro street I get bluescreens all the time, COD4 runs great many hours. I use these settings in BIOS:
CPU vcore: AUTO
CPU special add: 112.28%
NB voltage: 1.57V
MEM: 2.27V
CPU PLL: 1.75v
Clockgen: 3.60V
CPU VTT: 1.250V
C1E and EIST enabled
Vcore droop control: enabled
GTL values: are something like this Core0/Core1/NB : 62/60/63
MEM is set at 1:1 divider, and I run it @ 1000Mhz 4-4-4-12 with no problems.
I only have problems with NFS pro street. I'd like to get it run stable too, what should I do, and could someone explain how to get right GTL values. I took those from this topic. What does CPU VTT voltage do? Your help is needed!
how bout changing that one?Quote:
Originally Posted by J0kke
No, I have changed Vcore via special add, so I can use power saving options, in idle it drops voltages to 1.2 and frequency to 3000mhz and in load it jumps to 1.3 and frequency to 4000mhz. Any other suggestions?Quote:
Originally Posted by ninong
Has anyone tried the new 9/19 bios yet? I was curious to know if it has a new 4:3 memory divider that works with the QX9770[1600FSB].
I will eventually get a Xeon 3110 or E8600 and I am interested in the divider if there is one.I'm relatively new to overclocking (~1 year) and I greatly appreciate any input from experiences that anyone would care to share with me.
P.S. Has anyone tried PNY XLR8 DDR2-1173 in this board, perhaps even a P4 with hyper threading just for kicks?!
..::PC Signature::..
..........................:::::::::::::::::::Name-Tao Te Ching, Chapter 44
P4 631 D0 @ 4.41GHz@ 1.409V SL9KG Batch L731B297 w/Zalman 9500LED
2G PNY XLR8 DDR2-1173@ 980 4-4-4-15 @2.216V
Visiontek Reference 4870 512M w/Zalman VF1000
DFI UT P35 T2R!!!! w/-5/02 BIOS
Seagate es.2 250G 32M Hitachi Deskstar 750G 32M
Plextor PX-716A TEAC 3.5" Floppy
Thermaltake VA8003BWS w/ TT Toughpower 700 Watt [Seasonic]
Arctic Cooling MX-2 Fluke 179 Digital Multimeter Tripplite Isobar6
Scythe 120MM 110CFM 2X-Silenx 120MM 90CFM Zalman 90MM w/bracket
Anyone please? What should I put for GTL ? What are max CPU vtt and PLL volts for 24/7 use?Quote:
Originally Posted by J0kke
GTL settings are different for everyone. No one can tell you exactly what to do. Just read this article a couple times: http://www.anandtech.com/mb/showdoc.aspx?i=3129Quote:
Originally Posted by J0kke
This will also help http://edgeofstability.com/index.htmlQuote:
Originally Posted by J0kke
Leave PLL minimum
Set VTT to whatever it needs to be to run stable, none of the dual cores I have had need more than 1.3v so start minimum & work up.
Can anyone tell me where I can find a pre-45nm bios for that board ?
Thanks in advance :)
http://www.dfi.com.tw/portal/CM/cmpr...=537&mode=viewQuote:
Originally Posted by George_o/c
I think the 12-24 BIOS is pre 45nm. It's a great BIOS BTW.
But if you have a 65nm CPU you can use any of the newer BIOS' too.
No, I specifically want a pre-45nm bios for some SPi 1M runs with a E8400 ;) Thanks a lot mate :toast: :up:
i think the 11-07 is the pre-45nm bios. it has a problem with the 7.5 multi :(
but if you have e8600 you can get 11:29x-3xx in 400x10 1:1 :D
i don't know if it's gonna work with e8400 E0 but i think it would.
because my friend did 11:29x in 400x10 E8600 1:1 with bios 0317 :up:
Been testing my new Ballistix Tracer 16FD3 8500 on the LT P35, 400FSB 2:3 divider. I was encouraged by the fact that for this speed (600MHz CAS5) the sticks only need voltage set to 2.03V in the BIOS for memtest stability and figured they'd do 650MHz easily, but it doesn't seem to be the case. Zsamz must have made a deal with the devil or something for his crazy low-voltage high clocks.
That was my first short FSB test:
http://666kb.com/i/b3uxav9tbm236xlci.jpg
What FSB is possibille on the UT-P35-TR2?
Higher than any CPU will go.Quote:
Originally Posted by PlanetDynamic
Is anyone here successfully running 2 x 150GB Velociraptors in RAID-0 on this board without issues? I went through a hell of a time getting RAID to work on two 300GB Velociraptors when I built my dads computer back in May. I have read of numerous issues of lockups, freezes and event viewer errors when trying to run Velociraptors in RAID on onboard Intel based controllers.
Probably nothing, but have you actually memtested the RAM at those settings? Since it is rated for cas 5 @ 533Mhz, why not drop just back to cas 5 and see if you still BSOD?Quote:
Originally Posted by J0kke
Can I use middle pci express slot in X16 ? (no other card used)
I'm afraid not. :( You can only run it at X4 or X1 by changing it in the biosQuote:
Originally Posted by ultimeus
under the Genie bios field but, if you run it at x4 you lose your second Gigabit
Ethernet port because of how the PCI Express lanes are split up and used ;(
..::PC Signature::..
..........................:::::::::::::::::::Name-Tao Te Ching, Chapter 44
P4 631 D0 @ 4.41GHz@ 1.409V SL9KG Batch L731B297 w/Zalman 9500LED
2G PNY XLR8 DDR2-1173@ 980 4-4-4-15 @2.216V
Visiontek Reference 4870 512M w/Zalman VF1000
DFI UT P35 T2R!!!! w/-5/02 BIOS
Seagate es.2 250G 32M Hitachi Deskstar 750G 32M
Plextor PX-716A TEAC 3.5" Floppy
Thermaltake VA8003BWS w/ TT Toughpower 700 Watt [Seasonic]
Arctic Cooling MX-2 Fluke 179 Digital Multimeter Tripplite Isobar6
Scythe 120MM 110CFM 2X-Silenx 120MM 90CFM Zalman 90MM w/bracket
If I upgrade to an (45nM)E8500,etc..... is a clear cmos good enough or is it recommended to use all of the clearing jumpers(cmos,wont boot,and RTC) with this board?
Also are there any FSB speeds on this board where the PCI Express [Lock] unlocks and requires a PCI [Lock] setting of 101MHZ? I have heard of this before as a general experience but I am not sure if this even happens anymore.:shrug:
Any help with this query is most appreciated:up:
..::PC Signature::..
..........................:::::::::::::::::::Name-Tao Te Ching, Chapter 44
P4 631 D0 @ 4.41GHz@ 1.409V SL9KG Batch L731B297 w/Zalman 9500LED
2G PNY XLR8 DDR2-1173@ 980 4-4-4-15 @2.216V
Visiontek Reference 4870 512M w/Zalman VF1000
DFI UT P35 T2R!!!! w/-5/02 BIOS XP Pro 32Bit SP2
Seagate es.2 250G 32M Hitachi Deskstar 750G 32M
Plextor PX-716A TEAC 3.5" Floppy
Thermaltake VA8003BWS w/ TT Toughpower 700 Watt [Seasonic]
Arctic Cooling MX-2 Fluke 179 Digital Multimeter Tripplite Isobar6
Scythe 120MM 110CFM 2X-Silenx 120MM 90CFM Zalman 90MM w/bracket
hey guys
im back again
i love this board man and this forum even more. ive built so manny systems thus far and have seen much strange behavior when it comes to putting computers together.
but this by far is one of the strangest yet. last weekend i just swaped one of my drives for a much larger one. went through all normal procedures in swapping it. not much science there anyways. so as im beggining to reboot my system it started going into this strange loop of rebooting. heres what happens. power button is pressed. system starts to boot and 3 seconds shuts down. scratching my head it reboots 4 seconds later only to shutdown again. i dont even get to the dfi screen yet. this gets very repititious. as im tripping out the thing i noticed is that when i reest my system bios to factory state, she boots normally. i got back into bios reloaded to load my last bios and bammmm, the rebooting starts all over again. reset bios. reboot, re-enter bios to reload. wash rinse and repeat a few times and finally my system boots up. this has my scratching my head bigtime. any 1 ever experience anything like this?
i just reupdated my bios to latest release. and still happens. im overclocked. yes i am. i think my settings are not to conservative but not too exagerated either. all parts in my tower work fine. so wat in the world could this problem be comming from? doubt its my powersupply. computer reboots and stays running fine for hours at a time
lol this one got me good.
any help?
thanks guys for reading
peace
can you post your bios settings? It might be due to bad choice of memory settings etc
hope this helpsQuote:
Originally Posted by noinimod
thank you
sorry for repeated pic. these are my voltage settings only
ignore the rest on the bottom
thanks