I'm wondering if anyone is running like a 7 multi and getting beter FSB's for this chip, I am looking now to see, I figure that,
If i can figure the right combo for higher fsb then the chip MHZ will be easier. I also think i better get a few more MHZ then you because your mount will be here soon and then I bet your gonna break your current record. :up:
I wanna get my i7 on here while it's still cold out :surf:
running 471x8.5 right now. I need to order another UD3R as gigabyte never emailed me back about RMAing this one. I want to be over with it. I want my 4 gigs of ram back. Plus, ordering another board gives me the excuse to order some other things as well :D
http://valid.canardpc.com/cache/banner/487012.png
500x8 freezes. I think it's more of me pushing the Black Pis to 500mhz then the cpu not being able to manage it. I ordered some G Skill Pi 8800s, so it should be easy now. Only time will tell :D
Just got my Q9650 from UPS. L828A446 batch and 1.15 VID. Not sure if that's good but doing testing now.
Quote:
Originally Posted by koei
I wish I had your chip...
Can anyone give some suggestions on settings to boost large FFT Prime stability? I am able to tune the chip to Prime small FFT stable at 1.37v but large fails almost immediately.
post your bios settings please.Quote:
Originally Posted by koei
Actually I got it figured out. 1.31v at 8.5x500 Prime stable. This chip is turning out to be much better than I expected.
Bring it System! I feel I already have it for too long and I'm amazing nobody got there yet.Quote:
Originally Posted by systemviper
I did it on first run with all auto settings so it's time to go down :ROTF:
Post your SS and settings to help people around. Just saying you did this or that won't do any good for the community. :up:Quote:
Originally Posted by koei
Will do, gonna do some more testing first to make sure it's worthwhile posting.
The Crucial TracerRed came in today which swapped out the old G.SKILL Powerchip that didn't want to play nice for some reason at 500FSB. Primed for a little over 2H without problems and now just tightening some timing to finalize things. Anyways, here's the BIOS setup.
Code:
Robust Graphics Booster [Auto]
CPU Clock Ratio [8]
Fine CPU Clock Ratio [+0.5]
**********Clock Chip Control***************
CPU Host Clock Control [Enabled]
CPU Host Frequency (Mhz) [500]
PCI Express Frequency (Mhz) [100]
C.I.A 2 [Disabled]
*********Advanced Clock Control**********
CPU Clock Drive [1000mv]
PCI Express Clock Drive [1000mv]
CPU Clock Skew [50ps]
MCH Clock Skew [50ps]
*******DRAM Performance Control********
Performance Enhance [Standard]
Extreme Memory Profile (XMP) [Disabled]
(G) MCH Frequency Latch [400MHz]
System Memory Multipler [2.00D]
Memory Frequency [1000]
DRAM Timing Selectable [Manual]
CAS Latency Time [5]
tRCD [5]
tRP [5]
tRAS [15]
*******Advanced Timing Control***********
tRRD [Auto]
tWTR [Auto]
tWR [Auto]
tRFC [45]
tRTP [Auto]
Command Rate (cmd) [Auto]
>>>>> Channel A
Static tRead Value [9]
>>>>> Channel B
Static tRead Value [9]
***********Motherboard Voltage Control*******
Load-Line Calibration [Enabled]
CPU Vcore [1.33125V]
CPU Termination [1.440V]
CPU PLL [1.590V]
CPU Reference [0.912V]
MCH Core [1.500V]
MCH Reference [0.952V]
MCH/DRAM Refernce [1.050V]
ICH I/O [1.570V]
ICH Core [1.200V]
DRAM Voltage [2.100V]
DRAM Termination [1.050V]
Channel A Ref [1.050V]
Channel B Ref [1.050V]
*****************Advanced BIOS Features*********
Limit CPUID Max to 3 [Disabled]
No-Execute memory Protect [Disabled]
CPU Enhance Halt (CIE) [Disabled]
C2/C2E State Support [Disabled]
C4/C4E State Support [Disabled]
CPU Thermal Monitor [Disabled]
CPU EIST Function [Disabled]
Virtualization Technology [Disabled]
Hello everyone,
I was just looking for a list with yorkfields with the oc+batchnumbers for a new build with a q9550. Cant seem to find it.
It was a great help for my E8400 build, which now runs 4.55Ghz happily :) (air)
Thanks in advance
Hiya fellas,
Got my UD3P the other day and have been fiddling with it ever since. Could I first please just ask a few questions from you guys who have it.....
1. When priming @ 4.06GHz is it normal for the motherboard temp (using everest) to hit 68*C?
2. Does your CPU voltage (CPUz) jump around e.g when switching between high and low loads as I see mine going from 1.344v to 1.28v and vice versa.
Now down to the usual stuff.:) At present I'm at 4.06Ghz for reasonable temps :) However I've avtually booted at 4.5GHz.. But with any indication of my mouse pointer heading towards the Prime Small FFT button my system crashes, I'm actually not too bothered about that really as I'm just being carful trying to keeping voltages as low ass I can. I am more concerned though with the fact that I can't actually get anything Prime stable above my 4.0GHz :( I've tried a couple of the templates that you guys have used and they do get me to Windows but that's it. Stress testing is not possible.
I'm was really hoping to get to 4.2GHz Max Stable if that was possible with my stuff, so I was wondering If anyone perhaps has a template for that OC please (preferably with safe volts all round) with F7 BIOS.
Thanks for reading you guys ;)
Regards
Orb
is LLc safe for the cpu??
yes;)Quote:
Originally Posted by bobreece
Great for everyday use :)
q8200/ep45-ds5/2x2GB Geil Evo One PC6400
http://img220.imageshack.us/img220/3...00ocyx6.th.png
Hey nugzo, doing some testing with my Q9650 and UD3P, still trying to stabilize it (not asking for any help yet ;)) Anyways, your settings are working the best for me so far (I can at least boot up and run tests) I was just wondering, isn't CPU PLL 1.65 and MCH Core 1.6 a little high for those two? I took the cover of my NB and have a 90mm fan on it, and my CPU has low-end watercooling.
Anyone got a UD3R, Q9550 and 2x2gigs of ram successfully running? I still can nto get either of the two boards I have to run my Q9550 with two sticks of ram in it. One stick, it runs flawless all day. Two sticks, and it won't even boot to bios.
Yeah those are high. I should realy update this thread.... I will tonight. Check this thread out. Much more informative thread, even with the duals mixed in. My new settings are posted there. Links to the bios template i'm using are on page 73 as well as next post this thread. http://www.xtremesystems.org/forums/...d.php?t=205132Quote:
Originally Posted by sean222
These are my current 24/7 settings. 4410mhz, 8gb ddr2 @ 980mhz, GTX 295 22,000 in 3dmark06 and 23,000 in Vantage.
Here are my updated settings. My original post i didnt have gtls tweaked yet. I was able to drop all voltages.. The few minutes of Prime showing isn't for stability, just to show load temps. I am 12+ hours Small and blend stable with these settings.
http://img8.imageshack.us/img8/6098/capturemd7.jpg
Code:******Gigabyte EP45 UD3P******
Q9650 490 X 9 4410MHz
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.35GHz...........................[ 490 x 9 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 490 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 1000mv ]
PCI Express Clock Drive.........................[ 1000mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 50ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ 400MHz ]
System Memory Multipler.........................[ 2.00 ]
Memory Frequency 1066...........................[ 980 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ 52 ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ Auto ]
******Channel A Timing Settings******
Static tRead Value [ 7 ] ................[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 6 ] ................[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.23750 ]...................[ 1.41250 ]
CPU Termination [ 1.20 ]...................[ 1.40 ]
CPU PLL [ 1.50 ]...................[ 1.570 ]
CPU Reference [ 0.766 ]...................[ 0.871 OR 0.886 ]
MCH Core [1.1 ]...................[ 1.400 ]
MCH Reference [0.760 ]...................[ 0.926 ]
MCH/DRAM Refernce [0.900 ]...................[ 1.150 ]
ICH I/O [1.500 ]...................[ 1.570 ]
ICH Core [1.100 ]...................[ 1.200 ]
DRAM Voltage [1.800 ]...................[ 2.100]
DRAM Termination [0.900 ]...................[ 1.150 ]
Channel A Ref [0.900 ]...................[ 1.150 ]
Channel B Ref [0.900 ]...................[ 1.150 ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ]
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
Thanks goes out to Jor3lBR for the template.
Thanks for the update, and thanks for your BIOS settings, with some minor changes, I was able to stabilize my Q9650 @ 4.25GHz! Thanks!Quote:
Originally Posted by nugzo
My settings are posted here:
http://www.xtremesystems.org/forums/...postcount=1816
Anyone got a UD3R, Q9550 and 2x2gigs of ram successfully running? I still can nto get either of the two boards I have to run my Q9550 with two sticks of ram in it. One stick, it runs flawless all day. Two sticks, and it won't even boot to bios.
@Nugzo!
Nicely done mate I'm glad it worked out for you!
I'm using almost the exact settings as Flyfisher to hit 4.0ghz with 4x2gb of memory.
Ran Prime95 Blend for 25 hours.
I am just getting my proc up to speed and noticed that the temps are pretty good on everything with the cpu maxing at 63c which I dont think is too high for it. (is that too high?) Also the TMPIN2 reading from Hardware Monitor says it is 63c and I am unsure if that is too high as well. I do fold all the time when my pc is on so I hope you guys could let me know if those temps are too high or normal.
what is your CPU Batch #?Quote:
Originally Posted by flyfisher
It is an E0 L835B078.
a little help please,my friends board runs "thens re-boots by it self.on or off internet,we diabled the auto cooling/rmp in the bios and it still re-boots.
hears what hes got in the system below.
ddr2-ocz reaper 4 gigs
9700 zalman cpu cooler
stock bios settings
wxp pro sp3
ocz 520 power supply
4870/512 diamond vc
any help will be greatful thanks
That's your friends problem. If you're using 'stock settings' most likly your volts are way off and MCH and CPU Ref are off causing unstable;lity and consequent reboots.Quote:
Originally Posted by eagle101
I would browse around some 100+ pages in the Official Gigabyte U3P thread to get your friend optimal templates.
Did you try to put your two stiks of ram to another two red slots on the mobo.I think that is a whimsical board.Quote:
Originally Posted by clo007
I am trying to use Jor3lBR and Nugzo 's templates to get my q9650 on 4.4 stable
but i keep getting fatal error : final results was XXXXXXX, expected XXXXXXX under small fft in prime95 on 3cores
why?
thanks
i am really having trouble to 4.4ghz
running this setting can get me passes 20 times IBTCode:******Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.33GHz............................[ 482 x 9.0]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 482 ]
PCI Express Frequency (Mhz).....................[ 101 ]
C.I.A 2.........................................[ Disabled ]
******Advanced Clock Control******
CPU Clock Drive.................................[ 1000mv ]
PCI Express Clock Drive.........................[ 1000mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400 ]
System Memory Multipler.........................[ 2.00B ]
Memory Frequency 1066...........................[ 964 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD[3].........................................[ auto ]
tWTR[3].........................................[ auto ]
tWR[6]..........................................[ auto ]
tRFC[52]........................................[ 52 ]
tRTP[3].........................................[ auto ]
Command Rate (cmd)[0]...........................[ auto ]
******Channel A Timing Settings******
Static tRead Value [ 8 ] ................[ auto ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 8 ] ................[ auto ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.15 ]...................[ 1.38750 ]
CPU Termination [ 1.20 ]...................[ 1.30 ]
CPU PLL [ 1.50 ]...................[ 1.50 ]
CPU Reference [ 0.760 ]...................[ 0.87x( my memory is bad, but there is only one 0.87x ]
MCH Core [ 1.100 ]...................[ 1.320 ]
MCH Reference [ 0.760 ]...................[ 0.823 ]
MCH/DRAM Refernce [ 0.900 ]...................[ Auto ]
ICH I/O [ 1.500 ]...................[ 1.5 ]
ICH Core [ 1.100 ]...................[ 1.1 ]
DRAM Voltage [ 1.800 ]...................[ 2.100 ]
DRAM Termination [ 0.900 ]...................[ Auto ]
Channel A Ref [ 0.900 ]...................[ Auto ]
Channel B Ref [ 0.900 ]...................[ Auto ]
******Advanced BIOS Features******
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
running this setting cant get me pass IBT 20 timesCode:******Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.4GHz............................[ 489 x 9.0]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 489 ]
PCI Express Frequency (Mhz).....................[ 101 ]
C.I.A 2.........................................[ Disabled ]
******Advanced Clock Control******
CPU Clock Drive.................................[ 1000mv ]
PCI Express Clock Drive.........................[ 1000mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400 ]
System Memory Multipler.........................[ 2.00B ]
Memory Frequency 1066...........................[ 978 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD[3].........................................[ auto ]
tWTR[3].........................................[ auto ]
tWR[6]..........................................[ auto ]
tRFC[52]........................................[ 52 ]
tRTP[3].........................................[ auto ]
Command Rate (cmd)[0]...........................[ auto ]
******Channel A Timing Settings******
Static tRead Value [ 8 ] ................[ auto ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 8 ] ................[ auto ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.15 ]...................[ 1.4250 ]
CPU Termination [ 1.20 ]...................[ 1.40 ]
CPU PLL [ 1.50 ]...................[ 1.57 ]
CPU Reference [ 0.760 ]...................[ tried 0.886~0.971 (5 options) ]
MCH Core [ 1.100 ]...................[ 1.320 ]
MCH Reference [ 0.760 ]...................[ tried 0.886~0.96x( 3 options) ]
MCH/DRAM Refernce [ 0.900 ]...................[ Auto ]
ICH I/O [ 1.500 ]...................[ 1.57 ]
ICH Core [ 1.100 ]...................[ 1.2 ]
DRAM Voltage [ 1.800 ]...................[ 2.100~2.14 ]
DRAM Termination [ 0.900 ]...................[ Auto ]
Channel A Ref [ 0.900 ]...................[ Auto ]
Channel B Ref [ 0.900 ]...................[ Auto ]
******Advanced BIOS Features******
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
there is no bsod just the screen freeze, the best one is passes 6 times
any idea?
thanks!
I am very interested in using this thread. I have UD3P, Q9650, and 8GB PC8800.
I will be getting a new cooler and lapping my cpu soon, then I will post my clocks and temps and see if I can get 4.4!
Hey guys,
I'm trying to stabilize my Q9650 on my EP45-UD3P v1.6. I am mostly stable but temps are a major issue for me. I have load temps in the 80-90C range (ouch!!!). I am waiting for my Megahalems to show up but until then, I'm stuck using this crappy Antec cooler, it was the only thing I could find locally that was 1/2way decent.
Here are the settings I'm playing with, can anybody help me out with which of these have the most effect on loaded temps? I am trying to shave off as much voltage as possible to keep the box from melting down.
Q9650 @9x478 = 4.3ghz
vCore 1.375
cpu term 1.30
cpu PLL 1.57
cpu Ref .848
MCH core 1.34
MCH Ref .863
MCH / DRAM 1.110
I think I read that some people are lowering their Vcore and upping the CPU term, but now I can't find that thread for some reason. Are there any way to adjust GTLs per-core on this mobo? There doesn't seem to be but maybe I have to use a custom bios?? Currently I'm using the FDa beta.
cheers :up:
you cant adjust the cpu gtl's per-core with this board.
and the only way i think to lower temps is to lower vcore.
might try seeing if raising the cpu term helps with this,also
try adjusting cpu/mch ref voltages to help in lowering vcore.
so when u say adjust cpu/mch ref volts, do you mean lower them or raise them? i mean, if I start lowering vcore, do I have to raise cpu ref, or should I be lowering it to keep the .65x or .63x ratio for example?
you have to find the optimal cpu ref for your cpu and same thing
with the mch ref for your OC.once you find the right combo maybe you
can lower the vcore.you might be there already.its trial and error,try lowering the cpu ref and then see if its
stable then try lowering vcore see if its stable so on and so on.
that can take forever :rofl::rofl:Quote:
Originally Posted by radaja
most Q9650/95500 + UD3P i've seen on rev 1.0 love 1,20VTT / .785CPU / .80MCH relation, so you set that and then just notch VTT to whatever is needed and let the other values changeQuote:
Originally Posted by zsamz_
in my case worked perfect on x9 multi but need .84 on the MCH for 8,5multi
hope this helps
zsamz_ don't be lazy :rofl:
ok, just want to get this straight-- so let's say I'm prime stable at 1.375 with 0.848 vref(cpu). Are u saying I should start by lowering vRef but keep vCore at 1.375? I am trying to follow what you're saying about lowering the vRef but not sure if u mean lower them both together (vCore + Ref) or just adjust the vref by itself and keep vCore fixed. In the bios, as soon as you touch CPU term, the vRefs start changing on their own. I don't even know what "CPU term" really represents. Googled for hours today to try to find the true meaning and came up basically empty. Man, overclocking quad's on p45 = huge pain in the ar$e
Hey guys, just found this thread and I was wondering a few things...
I have a Q6700 (searched for that term in this thread but got no results :() and am having trouble getting it stable. I had a UD3R and ran 3.33GHz daily (thought that was pretty good until reading this thread :p) and got to 3.5GHz long enough for a 3DMark Vantage run with all voltage settings set to AUTO. Then I decided to go ATi + PhysX and sold the UD3R for a UD3P. Now, I am having trouble with stability on anything over 3.0GHz. I learned that I must've been lucky using all AUTO settings, so I changed the voltages myself to the values that were already suggested and upped the CPU VCore but I get Overvoltage/Overclock errors often.
Could my board be bad? I was so impressed by how stable the UD3R was out of the box, that I'm considering getting one again and ditching the dual GFX card idea. All my components are in my sig and if I can answer anything just ask.
Also, can I just plug in some of the settings that some of you are using, or do I need a successful set of Q6700 numbers?
Is it bad that I'm using 4 sticks of RAM?
My temps (right now) for my 4 cores are 45 44 38 42, and I've got Firefox and Windows Media Center (HDTV) open, and the room is somewhat warm (thanks to the computer and HDTV projector). GFX cards are at 58* C each.
HALP!
I say you get as high as possible by just setting your CPU voltage and MCH voltage and memory voltage. Then start trying to find the sweet spots for your other settings one at a time.Quote:
Originally Posted by pezcore
Then start moving up overclock wise once you see what settings your mother board likes. This should give you an idea roughly of where your motherboard likes its settings. You will have to tweak everything again but, you will be better off knowing roughly where to set everything.
cpu term is vtt.the ref tracks with the changing of vtt.here is a link that explains how it works.Quote:
Originally Posted by LuckMan212
http://www.xtremesystems.org/forums/...postcount=1157
what i mean about changing ref is try lowering it and then see if it is still prime95 stable.if so then see if your able to lower the vcore any.if so the thats good,if not try lowering the ref again or raising it.its a lot of work but if you want the most out of your components you need to know how they work.
just like what andressergio when using the 8.5 multiplier he needs a different mch ref 0.84v instead of 0.80v.
so when you cpu term(vtt) 1.20v in bios,then set cpu ref to 0.785v and mch to 0.80v now go back to cpu term(vtt) and raise it to 1.36v and the cpu and mch ref should change to 0.886v and 0.901v.see how they track?
Quote:
Originally Posted by andressergio
well i dont own a q9650 no more :rofl:
gave board to my kid:rofl::rofl:
he likes it:eek:
now i'm lookin for a good low vid 9650 lol n i'll give my 860 to him
or i'll but the kid a i750:yepp::p:
well i dont gotta work too hard with you people posting all the bios settings:rofl::rofl::rofl::rofl:
smart kiddo :DQuote:
Originally Posted by zsamz_
WeLL high vid i GOT :(
http://i50.tinypic.com/2rh5kkh.jpg