EP45-UD3P

Printable View

Show 100 post(s) from this thread on one page

12-22-2008, 03:45 AM
Ghostleader

Finally I´m stable

but first I would like to say thank you to SpeedEuphoria, radaja and most all pangingIII who made this possible. Thanks guys :clap:

Here it´s, 450 4050 1200 555 15 tRD7 Turbo, it passed 50 loop LinX, 5hrs Prime95 Blend, 1000% HCI memtest and 2hrs of loop with Crysis Benchmark Tool (Harbor Assault). :up:

http://i282.photobucket.com/albums/k...20055515tR.jpg

I know, my chip isn´t the best but it need that much juice (1,36 under load) to stable, therefore the temp, maybe if I reset my HSF I can cut 5C.

I´m not impress by the Bandwidth and latency but then again I´m use to X48 DDR2 performance.

But I most say, I still think this P45 chipset is a very sensitive one.

0,02 volt in either directing and it´s unstable or it even worst, it won´t boot and it´s the same with the MCH ref, two steps in either directing and it won´t play.

I now move on to 500 8 4000 1200 555 15
12-22-2008, 04:59 AM
radaja

C-N very impressive OC. Ghostleader,nice to see your making some headway.i also agree with you 100% about pangingIII, his help is greatly appreciated.
12-22-2008, 05:06 AM
1nsane

Here are my results sp far fsb wise. CPU not yet testet much. But it doesn't seam to run very well :-/

PLL i had to raise to 1,15 because of boot issues.

You think the MB Volts are fine ?

http://www.abload.de/thumb/520-rockstablepia5.jpg

Bios Settings

PHP Code:

MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ..................: Auto CPU Clock Ratio ..........................: 8 Fine CPU Clock Ratio......................: +0.0 CPU Frequency ............................: 4.16GHz (500x8.0) Clock Chip Control Standard Clock Control CPU Host Clock Control....................: Enabled CPU Host Frequency (Mhz) .................: 520 PCI Express Frequency (Mhz) ..............: 100 C.I.A. 2..................................: Disabled Advanced Clock Control CPU Clock Drive...........................: 800mv PCI Express Clock Drive...................: 900mv CPU Clock Skew (ps).......................: 0ps MCH Clock Skew (ps).......................: 0ps DRAM Performance Control Performance Enhance.......................: Turbo X.M.P............................................: Disabled MCH Frequency Latch......................: 333MHz System Memory Multiplier ................: 2.00b Memory Frequency (Mhz) ..................: 1040 DRAM Timing Selectable ..................: Manual Standard Timing Control CAS Latency Time.........................: 5 tRCD ....................................: 5 tRP......................................: 4 tRAS.....................................: 15 Advanced Timing Control [Press Enter] tRRD.....................................: 3 [Auto] tWTR.....................................: 3 [Auto] tWR......................................: 6 [Auto] tRFC.....................................: 52 [Auto] tRTP.....................................: 3 [Auto] Command Rate (CMD) ......................: 0 [Auto] Channel A Channel A Timings Settings (all on Auto) Static tRead Value......................: 10 (manuell) Channel B Channel B Timings Settings (all on Auto) Static tRead Value......................: 10 (manuell) Motherboard Voltage Control Load-Line Calibration.....................: Enabled CPU Vcore...............1.25000V..........: 1.387500 CPU Termination.........1.200V............: 1.260 CPU PLL.................1.500V............: 1.150 CPU Reference...........0.760V............: Auto (0,76V ET6) MCH/ICH MCH Core................1.100V............: 1.340 MCH Reference...........0.760V............: 0,698 (0,66 ET6) MCH/DRAM Reference......0.900V............: Auto ICH I/O.................1.500V............: 1,500 ICH Core................1.100V............: 1,100 DRAM DRAM Voltage............1.800V............: 1,920 DRAM Termination........0.900V............: Auto Channel A Address Vref..0.900V............: Auto Channel B Address Vref..0.900V............: Auto Advanced Settings Limit CPUID Max. to 3.....................: Disabled No-Execute Memory Protect.................: Enabled CPU Enhanced Halt (C1E)...................: Disabled C2/C2E State Support......................: Disabled x C4/C4E State Support....................: Disabled CPU Thermal Monitor 2(TM2) ...............: Disabled CPU EIST Function.........................: Disabled Virtualization Technology.................: Enabled
12-22-2008, 05:49 AM
radaja

1nsane,looks good. but im amazed that its able to boot at all with that low of pll. mine doesnt like anything below 1.57. ive tried 1.50 no boot. but like i said good job
12-22-2008, 05:59 AM
Ghostleader

Quote:

Originally Posted by 1nsane

Here are my results sp far fsb wise. CPU not yet testet much. But it doesn't seam to run very well :-/

PLL i had to raise to 1,15 because of boot issues.

You think the MB Volts are fine ?

doesn't seam to run very well, hmmm 16hrs Prime95

What are you not pleased with?

Your volt look pretty good except for PLL maybe, PLL 1,15 seems a little low, 1.50 are normal, if higher FSB try 1,50
12-22-2008, 06:20 AM
1nsane

I'm a little bit disapointed with my cpu because of the high vcore i need.
And my RAM are crab they only go 520 (1040). g.skill 1000 F2-8000CL5D-4GBPQ.

May be somebody has good settings to get behind 520 for that kit but i tried almost everything :-/
12-22-2008, 12:14 PM
HaxEJxuK

I was doing quick test on my UD3P and noticed something strange. When I set vcore to 1.35v in BIOS and 400x9 for FSB, in windows it's actually 1.376 and even under load it's 1.376v. Anyone experience this? Would there be any harm? I think I can re-adjust in BIOS to reflect in windows but wasn't sure if this is ok to start with.:confused:
12-22-2008, 02:36 PM
Homeless2

Quote:

Originally Posted by HaxEJxuK

I was doing quick test on my UD3P and noticed something strange. When I set vcore to 1.35v in BIOS and 400x9 for FSB, in windows it's actually 1.376 and even under load it's 1.376v. Anyone experience this? Would there be any harm? I think I can re-adjust in BIOS to reflect in windows but wasn't sure if this is ok to start with.:confused:

Do you have LLC enabled?
12-22-2008, 03:28 PM
HaxEJxuK

ha ha ha sorry forgot most important info. Yes, this happens when I enable LLC. without LLC it vdroop about .05v or so(If I remember correctly).

Quote:

Originally Posted by Homeless2

Do you have LLC enabled?
12-22-2008, 04:51 PM
Rich3077

Memory question here.. I have this ram http://www.newegg.com/Product/Produc...82E16820231194 and have tried to set my memory to PL9 like suggested earlier in this thread. By default SPD setting it is at PL 10 and if I try to change it to PL9 I get a failed overclock. Is it time for new RAM? If so I would like to try Corsair Dominators http://www.newegg.com/Product/Produc...82E16820145197 or this GSkill http://www.newegg.com/Product/Produc...82E16820231184

With DDR2 Ram prices so cheap I would like to keep a couple of extra kits around anyway in case a stick dies.

Thoughts?
12-22-2008, 06:25 PM
siyah

i have problems with kingston PC9200 4x1Gb mainboard giga EP-UD3R bios F5 what i make wrong to be stabil @4,0ghz or 4,2ghz multi 8-9 with a E8400 EO Batch Q828... V-ID:1,25
i habe 2x1GB in dual and single channel problems or 4x1GB the rams have I testet with memset with Boot Cd all Rams 100% ok.now i have G.Skill PC8000 2x2GB and it works fine 467x9=4,2ghz
with 1,34V-core but the rams end is maximum 520mhz thats not good for multi 8.and this memorys i have testet 4x1GB Ballistx Tracer with Leds it haves the same problems with Kingston.
the problems beginns @450 fsb multi 6-9 what i make wrong. sorry for my bad englisch.

http://geizhals.at/deutschland/a230778.html

http://geizhals.at/deutschland/a303966.html

this is g.skill pc8000 2x2GB prime stabil @4,2ghz

http://www.abload.de/thumb/42prime80min.t7c9.jpg
12-22-2008, 06:41 PM
radaja

siyah, so you rock out while priming and stressing? i never thought of doing that.i just sit in silence and watch and pray. hehe. oh and im not sure exactly what your asking? ithink maybe trouble getting stable with the kingston ram?
12-22-2008, 06:55 PM
siyah

@radaja

My question is why the Kingston and Crucial memory is not stable over 450fsb can go? I have no problems and prime music to hear otherwise there will be so boring
12-22-2008, 07:11 PM
radaja

siyah, post all your bios settings(voltages and memory sub timings). what pl level are yor running? give us as much details as possible,so we can help. and about the music,im just jealous i never thought of it.cause your right its boring while priming.
12-22-2008, 07:39 PM
siyah

Here are my current settings much can be done with Easy Tune 6 to read the rest of the store is consistent with everything on auto timmings PL, etc.

stromsparfuncionen ICE disabled memory standard, pci 100, memory divisor 2.0 B,LLC enabeld

I need your ram G.skill pc8800 :)

http://www.abload.de/thumb/42prime144min.3ai8.jpg
12-22-2008, 07:48 PM
radaja

siyah, maybe up the vMCH from 1.2 to 1.3 or higher,maybe add a little more vDIMM see if that helps.
12-22-2008, 08:18 PM
siyah

Quote:

Originally Posted by radaja

siyah, maybe up the vMCH from 1.2 to 1.3 or higher,maybe add a little more vDIMM see if that helps.

yes its boot vMCH @1,4 vDIMM 2,28V :clap:

thangs man ram 2.0D work,do not works on 2.0B

i am testing @4,2 or higher

http://www.abload.de/thumb/42primekingston11.t55w.jpg
12-22-2008, 08:37 PM
stn0091

Here I am with my Q9550 at 490x8.5. I could really use some help making that last jump to 500x8.5 if it's not an impossible feat.

It completed twenty passes in Intel's Burn Test at 490x8.5; OCCT ran for two hours; I haven't tried with Prime95 yet.

PHP Code:

******************************************************* MB Intelligent Tweaker(M.I.T.) ******************************************************* Robust Graphics Booster ..............: [Fast] CPU Clock Ratio ......................: [8X] Fine CPU Clock Ratio..................: [+0.5] CPU Frequency ........................: 4.17GHz (490x8.5) ************** Clock Chip Control ************** >>>>>> Standard Clock Control CPU Host Clock Control................: [Enabled] CPU Host Frequency (Mhz) .............: 490 PCI Express Frequency (Mhz) ..........: [100] C.I.A.2 ..............................: [Disabled] >>>>>> Advanced Clock Control.........: [Press Enter] CPU Clock Drive.......................: [900mV] PCI Express Clock Drive...............: [900mV] CPU Clock Skew (ps)...................: [0ps] MCH Clock Skew (ps)...................: [0ps] *********** DRAM Performance Control *********** Performance Enhance...................: [Standard] (G)MCH Frequency Latch................: [400MHz] System Memory Multiplier .............: [2.00D] Memory Frequency (Mhz) ...............: 980 DRAM Timing Selectable ...............: [Manual] >>>>>> Standard Timing Control CAS Latency Time......................: 5 tRCD .................................: 5 tRP...................................: 5 tRAS..................................: 15 >>>>>> Advanced Timing Control........: [Press Enter] tRRD..................................: [AUTO] tWTR..................................: [AUTO] tWR...................................: [AUTO] tRFC..................................: [AUTO] tRTP..................................: [AUTO] Command Rate (CMD) ...................: [2] >>>>>> Channel A Timing Settings......: [Press Enter] Static tRead Value....................: [9] tRD Phase0 Adjustment.................: [AUTO] tRD Phase1 Adjustment.................: [AUTO] tRD Phase2 Adjustment ................: [AUTO] tRD Phase3 Adjustment.................: [AUTO] Trd2rd(Different Rank)................: [AUTO] Twr2wr(Different Rank)................: [AUTO] Twr2rd(Different Rank)................: [AUTO] Trd2wr(Same/Diff Rank)................: [AUTO] Dimm1 Clock Skew Control (ps).........: [AUTO] Dimm2 Clock Skew Control (ps).........: [AUTO] DDR Write Training....................: [AUTO] >>>>>> Channel A Driving Settings.....: [Press Enter] Driving Strength Profile..............: 1066MHz Data Driving Pull-Up Level............: [AUTO] Cmd Driving Pull-Up level.............: [AUTO] Ctrl Driving Pull-Up Level............: [AUTO] Clk Driving Pull-Up Level.............: [AUTO] Data Driving Pull-Down Level..........: [AUTO] Cmd Driving Pull-Down level...........: [AUTO] Ctrl Driving Pull-Down Level..........: [AUTO] Clk Driving Pull-Down Level...........: [AUTO] >>>>>> Channel B Timing Settings......: [Press Enter] Static tRead Value....................: [9] tRD Phase0 Adjustment.................: [AUTO] tRD Phase1 Adjustment.................: [AUTO] tRD Phase2 Adjustment ................: [AUTO] tRD Phase3 Adjustment.................: [AUTO] Trd2rd(Different Rank)................: [AUTO] Twr2wr(Different Rank)................: [AUTO] Twr2rd(Different Rank)................: [AUTO] Trd2wr(Same/Diff Rank)................: [AUTO] Dimm1 Clock Skew Control (ps).........: [AUTO] Dimm2 Clock Skew Control (ps).........: [AUTO] DDR Write Training....................: [AUTO] >>>>>> Channel B Driving Settings.....: [Press Enter] Driving Strength Profile..............: 1066MHz Data Driving Pull-Up Level............: [AUTO] Cmd Driving Pull-Up level.............: [AUTO] Ctrl Driving Pull-Up Level............: [AUTO] Clk Driving Pull-Up Level.............: [AUTO] Data Driving Pull-Down Level..........: [AUTO] Cmd Driving Pull-Down level...........: [AUTO] Ctrl Driving Pull-Down Level..........: [AUTO] Clk Driving Pull-Down Level...........: [AUTO] ********* Motherboard Voltage Control ********* Voltage Types...........Normal..........Current ----------------------------------------------- >>>>>> CPU Load-Line Calibration.................: [Disabled] CPU Vcore..............1.275000v......: [1.49375] (1.392 load) CPU Termination........1.200v.........: [1.42] CPU PLL................1.500v.........: [1.59] CPU Reference..........0.780v.........: [0.899] (0.760 when VTT @ 1.20) >>>>>> MCH/ICH MCH Core...............1.100v.........: [1.48] MCH Reference..........0.800v.........: [0.939] (Not sure of value when VTT @ 1.20) MCH/DRAM Ref...........0.900v.........: [AUTO] ICH I/O................1.500v.........: [1.570] ICH Core...............1.100v.........: [1.100] >>>>>> DRAM DRAM Voltage...........1.800v.........: [2.12] DRAM Termination.......0.900v.........: [AUTO] Channel A Reference....0.900v.........: [AUTO] Channel B Reference....0.900v.........: [AUTO]
12-22-2008, 09:16 PM
EliTE22

try 1.65v pll that should set u for any clock higher (any)
increase cpu termination if needed
cpu reference .935v
MCH core up to 1.5v-1.55v?
MCH ref. .990v
MCH/Dram 1.120v
ICH core 1.2
u may have to enable loadline??? try ^ first
with llc you should be able to lower vcore way down
what ur temps???
12-22-2008, 09:45 PM
fatguy1992

Hey could someone please tell me the max safe MCH volts for 24/7 on the stock NB cooler? Thanks
12-22-2008, 09:54 PM
EliTE22

Quote:

Originally Posted by fatguy1992

Hey could someone please tell me the max safe MCH volts for 24/7 on the stock NB cooler? Thanks

ive been running 1.6v, id say that as high as you'd want to go 24/7, i seen 1.74v and 1.8v for benching
how high r u right now?
12-22-2008, 10:04 PM
Jor3lBR

Quote:

Originally Posted by EliTE22

ive been running 1.6v, id say that as high as you'd want to go 24/7, i seen 1.74v and 1.8v for benching
how high r u right now?

If the temps are below 45oC I wouldn't worry about it. Problem is there is a range that high nb volts will start to hurt more then do good.
12-22-2008, 10:09 PM
EliTE22

there only one thing about this mobo i dont like, the Realtek HD audio manager, on my other boards (all mobos about) have a option for stero audio to change to 5.1 or 7.1, i dont:down: and it doesnt even show my rear speakers:( through analog i only get stereo audio:mad: , im able to use the digital out it works great, any one less have this problem????

on a positive+ i was able to oc my ram to 1200MHz at 2.2v cas5-5-5-15:D on this mobo, my tpower i45 couldnt even get over 1080 at 2.4v same ram:ROTF:
12-22-2008, 10:21 PM
Jor3lBR

Quote:

Originally Posted by EliTE22

there only one thing about this mobo i dont like, the Realtek HD audio manager, on my other boards (all mobos about) have a option for stero audio to change to 5.1 or 7.1, i dont:down: and it doesnt even show my rear speakers:( through analog i only get stereo audio:mad: , im able to use the digital out it works great, any one less have this problem????

on a positive+ i was able to oc my ram to 1200MHz at 2.2v cas5-5-5-15:D on this mobo, my tpower i45 couldnt even get over 1080 at 2.4v same ram:ROTF:

Nice Elite I just fired mine today, keep your template updated as I will be using it for starters. :clap:

Being a DFI man fr all these years these other bios looks like Japanese to me.
12-22-2008, 10:32 PM
EliTE22

Quote:

Originally Posted by Jor3lBR

Nice Elite I just fired mine today, keep your template updated as I will be using it for starters. :clap:

Being a DFI man fr all these years these other bios looks like Japanese to me.

know what u mean, came from a tpower and nvida, like a foreign country:D
ill update my template in a little while and even my 4.7GHz setting:up:

Show 100 post(s) from this thread on one page

** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P