Printable View
Yes, i explained it on some other posts, as here, here and also hereQuote:
Originally Posted by sxs112
Btw, finally my NB Voltage is upped two notches (1.18V BIOS - 1.205V Measured) and one at FSB (1.32V BIOS - 1.24V Measured) to make F@H stable with SMP and GPU at the same time, also i had to set the CPU GTL Ref to 0.61x to avoid sudden reboots
I can explain further if you need it :) Thank you :up:
Quote:
Originally Posted by sxs112
Thank you sir!:up:
note:
nbs400 no longer works (at all) using beta bios 1004 (P5Q)
I'm testing DLX BIOS 1102 today, its looking very good, rock solid!
Temp sensors are working fine now.
My previous OC profiles wouldn't boot with 1102, so be sure to start OCing from defaults and manually enter values.
For those that are very cautious about beta bioses, I would say that this one is worth.
Hello
I have a problem.
I would like to do 500x8 and 1:1. If I put PL at 10 i need 1,4v at NB.
I have a 2x2Gb DDR2 1000 Kit (GSKILL PI).
Also, I need to set manually AI Clock Twister to Lighter, Otherwise it's unstable.
Is this problem my memory or my motheboard ?
AI Overclock tuner: Manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: 333
FSB Frequency: 500
PCI-E Frequency: 100
DRAM Frequency: 1002Mhz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 4
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: Lighter
AI Transaction Booster: Manual
Common Performance Level [10]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.3875
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.58
FSB Termination Voltage: 1.32
DRAM Voltage: 2.00
NB Voltage: 1.40
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.50
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
Hi guys :)
So, I started out with a P5Q-E, and tweaked it a lot trying to get Prime95 stable, but just couldn't seem to get there -_-. On top of that it seemed like it didn't like my 4x1GB arrangement on ram.
So, I decided to get a P5Q Deluxe to replace it. Seems like a good board; RAM runs a lot cooler for whatever reason, and Prime95 seems happy.
Anyhow, I'm having a problem with it in which I can't entirely remember if the P5Q-E did the same thing...
When I play a game, such as a mod for HL2, if I get a bunch of sounds going at once, it seems to overwhelm the on-board sound and it just gets progressively cracklier until it fades out to silence, and then it fades back in once the sounds die down. I'm not entirely sure what to do about this :(
I did have some other problems, but they seem to have departed after I reformatted, which included the sound *not* coming back after it crackled out, my video card giving me a Code 10 (device cannot start), and in gaming I'd get these temporary hangs for about 20 seconds. I haven't seen that crop up *yet*, but I do wonder about it.
So, I'm wondering if this is a driver problem, or a problem with this particular P5Q-D such that I should exchange it for a new one...
Running 0704 if that makes a difference. I could try some other bios if you guys want, but I don't entirely understand the interaction there so I haven't tried every bios out there.
Level 10, NB: 1,36, SB 1.20
http://img255.imageshack.us/img255/3...est2lt3.th.jpg
http://img255.imageshack.us/img255/4...el10sb1.th.jpg
When are they going to fix the 1:1 memory PL timings?
P5Q-E owners:
is anyone else experiencing a 500 FSB wall with this board? 499 FSB works fine but anything more is unstable. i've tried both the qx9770 and e8400 with no luck. if you're stable over 500 fsb, could you please share your settings with me? thanks in advance
HELP NEEDED PLEASE
Just had a out of the blue reboot.
On booting back up Windows XP loaded then there is a small pause while the DVDRW etc is read and such then the final parts to loading the OS usually continue to load - but it reboots and ends up in a cycle.
I've had to turn off PC at the PSU switch then back on.. now it will boot ok into the OS.
I've checked event viewer and I can't see anything that is revealing anything.
Anyone have any suggestions if this could be hardware related or OS?
Will my PSU be ok for the hardware below?
Mobo: Asus P5Q Del (latest bios)
PSU: Corsair 620w
Q6600 (G0)
4GB Crucial Ballistix
ATI Radeon 3780 GC
2 x 1TB WD HDD
1 x 1TB Samsung spinpoint
1 x 500gb WD (Vista OS)
2 x 160GB WD in Raid0 (Win XP Pro 64 OS)
3 x scyte 120mm case fan
1 x 120mm fan on CPU cooler
2 x 80mm case fans
1 large side fan (with thermaltake case)
2 x DVDRW drives
AI Overclock tuner: Manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: 333
FSB Frequency: 333
PCI-E Frequency: 101
DRAM Frequency: 1066Mhz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Auto
MEM. OC Charger: Auto
AI Clock Twister: Auto
AI Transaction Booster: Manual
Common Performance Level [8]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.26875
CPU GTL Voltage Reference (0/2): 0.630
CPU GTL Voltage Reference (1/3): 0.670
CPU PLL Voltage: 1.58
FSB Termination Voltage: 1.28
DRAM Voltage: 2.12
NB Voltage: 1.24
NB GTL Reference: 0.630
SBridge Voltage: Auto
PCIE SATA Voltage: Auto
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal
All CPU extras Disabled.
Any help appreciated.
Blew out 1102 on earlier stable settings. thank god for that back-up bios chip.
eWWW did you try loading your old profile or try falshing it while overclocked?
Neither, I just tried turning it on.
Anyone else having some problems with the onboard audio? Assassins Creed has that problem where I can't hear any of the voice overs unless I turn down audio accelleration 1 notch in dxdiag. I had the exact same problem on my old s939 board but a driver update fixed it.
Anyone else running into this and found a way to fix it without turning down the audio acceleration features?
Anyone else noticed QFan options doesn't do anything? Or is there anything special with Noiseblocker BlackSilent XL2 fans that i'm not aware of?? No matter what i do (QFan Silent/Standard/Turbo/Disabled) it always spins at 1400 rpm. Ugh... I'm using BIOS 0803. And same applies to all other fan pins. I had to use connector adapter with resistor on it to slow down that additional chipset fan...
U used prime64v256, right? Never had problems with it on my vista x64Quote:
Originally Posted by truehighroller
Then again I'm not responsible if it messes your or anyone elses system :)
EDIT: Hmm. actually I have not used its blend test that much. Too hangoverish. My brains not working properly :)
Going to test blend right now and see what happens xD
Quote:
Originally Posted by truehighroller
Forever eh?
Stability is just that.......stable!
Small FFT's means jack imho regardless of what people say. I've seen overclocks pass Small FFT's for hours and hours on end but then fail without doubt when running Large FFT's.
Personally I'll always run Large FFT's to test stability, if it passes Large then I'm satisfied.
An oc may seem fine because it passes Prime Small FFT's...........whether it will pass Large FFT's is another thing though. I'm not alone in this understanding that Large FFT's causes more stress on the overclock than Small, and there are quite a few others around that will test stability using Prime Large FFT's specifically for this reason. :yepp:
Do a memtest in windows via OCCT ram test or co... could be one of your dimms is flakey... also you gave them real volts in reality, were you aware of that ? if Ram is okay, I would up Vcore to 1.35 and disable Loadline calibration...Quote:
Originally Posted by MonsterDK
I tested the Qfan option for the chassis fans with 1001 and 1102 and it works fine.... tested fans are PAPST GL fan, Zalman 8700 CPU fan, Scythe Flex 1200,... could be that your fans cannot be regulated by the Qfan option... or you need to update to a later bios...Quote:
Originally Posted by RejZoR
Small FFT's only used for CPU test is okay mate... ram and NB require blend or large pass... though I had OC's fail on large yet had no sign of instability whatsoever in gaming, folding,... no test is bulletproof... you can pass large and run ya first 3dmark and crash...Quote:
Originally Posted by lowdog
Stability is like you say : stable at all times... you will need to run multiple programs and co ( superpi, 3d benches, OCCT, and co to test stability) and then daily usage is the best way to see if it's stable for the user and not some test program....
People are abit obsessed by getting the lowest voltage in prime while yet that small extra increment can make a world of difference...
Well, BlackSilent XL2 has the tacho line so it should work. I've tried some later BIOS 10xx but it just froze when it should reboot after 5 seconds and when i exit BIOS settings it freezes too. So it's a no go for me. Not sure (yet) why that happens...
Good way to test stability is to run latest real-time strategy games, especially the ones that have masses of units to command.
Strategy games really stress everything from CPU, memory, graphic card and even disk and chipset.
Second good stress test with real conditions are timedemos in Crysis. Heavy graphics and CPU usage really puts some serious load on to system.
Usually if it passes these two it will most probably pass anything.
Hi guys,
I just got my p5q-e in to replace my trusty old p5k-prem.I set my discs up in raid 0 and it works fine on this board :D they are samsung sp2504c's.Whats the best bios for this board please? it loaded with 0610(i think now)
I pushed it up to 400fsb,which is my normal oc for my chip which is 3.2ghz/1.35vcore/1066mem.i will give it a couple of days and try it higher,my p5k-prem managed 500x8 with my chip.The vcore was 1.5625v for that.
I am pretty impressed upto now,it seems faster then the prem at the same clock speed.
Is there a specific thread for the p5q-e? also how does the duel bios thing work? can you switch to the second one in case of a problem or is it automatic? and if you flash a newer bios and want to go back to an older one,is it easier than wth the prem?
thanks.
I try to push q9450 on P5Q (0703 BIOS) and see that the prime is only stable if I set Vcore high.
PLL, VTT do not influence stability at all that I want on particular FSB
I tried PLL 1.52-1.6 and VTT 1.22-1.38
The wall I reach is 470FSB on Vcore=1.4 LLC=on (the windows loads on 485, but prime is not stabile)
Some other stable FSBs:
440 on Vcore=1.3 LLC=on
450 on Vcore=1.36 LLC=on
460 on Vcore=1.38 LLC=on
What can I do to go above 470????? I think Vcore=1.4 is already too high ……
I have 1066 mem so it is not a show stopper
CPU Ratio Setting: 8
FSB Frequency: 470
PCI-E Frequency: 100
DRAM Frequency: 1:1
CPU Voltage: 1.4
CPU GTL Voltage Reference (0/2): AUTO
CPU PLL Voltage: 1.58
FSB Termination Voltage: 1.28
DRAM Voltage: 1.92
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: 1.2
PCIE SATA Voltage: AUTO
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal
Uh...just in case you don't already realize this, sounds like your RAM isn't too stable.Quote:
Originally Posted by truehighroller
If blend if causing your OS to corrupt, well yeah...
Only thing I see is to mess with the GTL voltages, but think you gotta get another CPU that needs less volts... most CPU's need a whole lotta extra volts over a certain speed for a few hundred Mhz more... if you need already 1.36 at 3.6ghz I think it's better to leave it at that speed then...and call it a day...Quote:
Originally Posted by petekol
I got the new bios for the p5q-e and the voltage damper option works (in the old bios I didn't notice I had it). It even raises the vcore a bit under load (don't know how safe this is, but it's still lower than what I set in bios).
Does anyone know how can I start the computer with a usb flash drive stuck in, without the mb trying to boot from it (I get an error and I have to restart without the "stick" in)?
Raise your Northbridge volts.Quote:
Originally Posted by petekol
Change the hard drive boot order in the BIOS so that it boots off the first hard drive and not the USB drive.Quote:
Originally Posted by ebh
What i do is only have 1 boot device,my raid setup,and use F8 if i want to boot something else.
AI Overclock tuner: Manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: Auto
FSB Frequency: 450
PCI-E Frequency: 101
DRAM Frequency: 1081Mhz
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
3rd Information :
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Disabled
AI Clock Twister: Lighter
AI Transaction Booster: Manual
Common Performance Level [10]
CPU Voltage: 1.34375
CPU GTL Voltage Reference: AUTO
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.22
DRAM Voltage: 2.12
NB Voltage: 1.22
SBridge Voltage: Auto
PCIE SATA Voltage: Auto
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
Been taking your advice in this thread and here is where I am right now. P5Q-Pro 0901 Bios, E8400
9X450 100% Stable RAM is at 5/4 540MHZ
Whenever I drop ratio to 7-8 and set RAM to 500MHZ and try 1/1 I get errors in Windows.
Should I be happy with 4050mhz running 5/4 DDR2-1081 and just try to start working on memory timings or should I try to get the higher FSB?
Im not sure what higher FSB will get for me if RAM is already running 1081mhz at decent settings.
I am REALLY happy with my overclock so far.
Hello Leeghoofd,Quote:
Originally Posted by Leeghoofd
I tried to mess with GTL voltages but when I set them manually I get errors. For example I tried to set CPU GTL's at 630 or more and NB GTL at 550 or 630 or more and I get errors. I have 1102 bios. Is this a problem with that bios ?
I didn't know they had that version prime no. Yah I sat here and played Devil May Cry all night last nighht and no probs where I'mn at right now 485 x 8 1.3v~.Quote:
Originally Posted by JHS
I was just wondering if anyone here has noticed that with BIOS 1102 you can now run PL7 with both pull-ins 1 & 3 enabled? I first tried PL7 Pull-in 3 enabled and it survived 1 hour large FFT's. I then tried PL7 2&3 enabled but my computer locked up after 10 minutes of prime. Next was PL7 1 & 3 enabled and I am now sitting at 1 hour prime and still going.
This was all done with the following settings:
400 Strap | 1066MHz
5-5-4-15-3-35
DRAM Static Rd: enabled
DRAM Rd Trainging: Disabled
Mem OC Charger: Disabled
Ai Clock Twister: Strong
Performance Level: 7
6 | 7 | 6 6 | 7 | 6
CPU Voltage: 1.26V
CPU GTL (0/2): Auto
CPU GTL (1/3): Auto
CPU PLL: 1.52V
FSB Term: 1.18V
DRAM Voltage: 2.14V
NB Voltage: 1.22V
Loadline: Enabled
CPU PCIE Speed Spectrum: Disabled
CPU/NB Skew: Normal
Newest feature (added in 1102): Performance
After this passes two hours I'm going to bump up the NB voltage to 1.32V and try to get Pullin 2 to work.
----------
Edit: I just wanted to add that so far I haven't seen any benefits from enabling PL7 in Everest bandwidth tests.
can you show me your bios setup I'm trying to get 3.8 stable.Quote:
Originally Posted by truehighroller
Quote:
Originally Posted by TouGe
I might have to try that thanks but, what are your other settings?
Rusty, I posted all my settings between 3 to 7 pages back for my 3.8 settings.
ok here's mine, need help to make it stable at 3.8Quote:
Originally Posted by truehighroller
AI Overclock tuner: manual
CPU Ratio Setting: 8
FSB Frequency: 475
FSB Strap to North Bridge: 400
PCI-E Frequency: 100
DRAM Frequency: DDR2-950MHz
DRAM CLK Skew on Channel A1: auto
DRAM CLK Skew on Channel A2: auto
DRAM CLK Skew on Channel B1: auto
DRAM CLK Skew on Channel B2: auto
DRAM Timing Control: manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : Auto
Row Refresh Cycle Time: 55
Write Recovery Time: Auto
Read to Precharge Time: Auto
2nd Information :
READ to WRITE Delay (S/D): Auto
Write to Read Delay (S): Auto
WRITE to READ Delay (D): Auto
READ to READ Delay (S): Auto
READ to READ Delay (D): Auto
WRITE to WRITE Delay (S): Auto
WRITE to WRITE Delay (D): Auto
3rd Information :
WRITE to PRE Delay: Auto
READ to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Disabled
AI Clock Twister: Auto
AI Transaction Booster: Auto
Common Performance Level 05
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHA PH4: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
Pull-In of CHB PH4: Disabled
CPU Voltage: 1.33xx
CPU GTL Voltage Reference (0/2): 0.675
CPU GTL Voltage Reference (1/3): 0.675
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.30
DRAM Voltage: 2.10
NB Voltage: 1.34
NB GTL Reference: Auto
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.50
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : normal
NB Clock Skew : normal
Advance CPU Settings
CPU Ratio Setting: 8
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
___________________________
specs:
q9450
p5q-dlx bios 1102
red ballistix-6400 4-4-4-12-2T 1.8v-2.2v
evga 8800gtx
psu 850 realpower cm
wd750gb hdd caviar re2
Thermalright 120x
I could not get 7 to load at all with 1 and 3 enabled all disabled all enabled,,. I can however get 8 with all enabled to load though. I don't know what they all mean any way so. Wow you need to change your pl setting to 10 man. "Rusty". "Common Performance Level 05" needs to be ten or more. That is the 1:1 setting and the pl sucks on it? You also have toi much voltage on the nb you only need 1.26 or 1.28.
anything else ?Quote:
Originally Posted by truehighroller
prime fails almost right away with threads 1 and 3.
p.s> do I need to enable all of these?
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHA PH4: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
Pull-In of CHB PH4: Disabled
Ok here do this,
CPU Voltage: 1.33xx
CPU GTL Voltage Reference (0/2): 0.63
CPU GTL Voltage Reference (1/3): 0.63
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.32
DRAM Voltage: 2.12
NB Voltage: 1.28
Anyone help me please ?Quote:
Originally Posted by yenclas
with ya current setup you can get some more bandwith with a lower PL and later on try clock twister at moderate (depending on ya ram), in bold are the settings for 500FSB... most important you need more Vcore and NB voltage than with 9 multi and 450FSB...
Quote:
Originally Posted by Tirade
Rusty try more Vcore mate, try 1.35 for a while....Quote:
Originally Posted by rusty
Yenclas if you are sure your CPU already needs 1.36 Vcore for 3.6Ghz mate you got a mediocre batch... if you want more you prolly have to give 1.4 or more for a few hundred Mhz more...one of the reasons I told you to stick with ya current stable OC at 3.6ghz...Quote:
Originally Posted by yenclas
Just a question how are ya temps ? at idle at and under load ? if they are pretty high you might want to check if your IHS of your CPU is flat... if not you prolly have to lap it...
He just copied my template mate, he's on auto so most of the time PL will be 10 or more... no worries thereQuote:
Originally Posted by truehighroller
nobody?? :DQuote:
Originally Posted by R@ptor =]]
I think you have to mess a bit with the Skews mate to get them stable... that's really trial and error, delay 150 worked fine for the Mushkins here to get them over 1100mhz... Gskills here are no go....Quote:
Originally Posted by R@ptor =]]
hi,guys here the newest bios P5Q.ASUS-DELUXE-1003 musst be final
http://rapidshare.com/files/13121117...ELUXE-1003.rar
edit:do you know why the SixEngine_V10016 cannot see on the homepage by deluxe only p5q,p5q.pro and so on you see the V10016 but by p5q-deluxe is still the old 10012?? also on the servers cant see the new one...you know why?
sorry my english^^
Hi everyone, I've got a bit of a problem. I've been running prime95 without issue, however when I try to play games (Call of Duty 4, Mass Effect...) the games freeze after about 5-10 minutes. I have had it up to 3.6 (9x400) with 1.45v and prime would run fine and I think I could run with even lower vcore. My temps were good too (around 63C on the hottest core) and at 3.2 (55-56C), what could be causing the games to crash? I am new to OCing and any advice or help would be appreciated.
AI Overclock tuner: Manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: 266
FSB Frequency: 400
PCI-E Frequency: 101
DRAM Frequency: 1003Mhz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 12
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: AUTO
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO
CPU Voltage: 1.4250
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.28
DRAM Voltage: 1.98
NB Voltage: 1.24
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
new option in the new bios 1003..... cpu margin enhancement......what this is doing?
edit:somebody know if i can use the sixengine from the p5q.pro ... p5q....p5q-e also for the p5q.deluxe?
on the homepage you can see all p5q becoms a new version 10016 but only the p5q-deluxe have still the old one 10012..why? epu must be the same chip on all mobos so can i use oder better wait?
Quote:
Originally Posted by truehighroller
PHP Code:ASUS P5Q DLX Template :
JumperFree Configuration Settings
AI Overclock tuner:
CPU Ratio Setting: 9.0
FSB Strap to North Bridge: 400
FSB Frequency: 400
PCI-E Frequency: 101
DRAM Frequency: 1066
DRAM CLK Skew on Channel A1: Auto
DRAM CLK Skew on Channel A2: Auto
DRAM CLK Skew on Channel B1: Auto
DRAM CLK Skew on Channel B2: Auto
DRAM Timing Control:
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 4
DRAM RAS# Activate to Precharge: 12
RAS# to RAS# Delay : 3
Row Refresh Cycle Time: 35
Write Recovery Time: 6
Read to Precharge Time: 3
2nd Information :
READ to WRITE Delay (S/D): 7
Write to Read Delay (S): 3
WRITE to READ Delay (D): 5
READ to READ Delay (S): 4
READ to READ Delay (D): 5
WRITE to WRITE Delay (S): 4
WRITE to WRITE Delay (D): 6
3rd Information :
WRITE to PRE Delay: 12
READ to PRE Delay: 5
PRE to PRE Delay: 1
ALL PRE to ACT Delay: 4
ALL PRE to REF Delay: 4
DRAM Static Read Control: Enabled
DRAM Read Training: Disabled
MEM. OC Charger: Disabled
AI Clock Twister: Strong
AI Transaction Booster:
Common Performance Level: 7
Pull-In of CHA PH1: Enabled
Pull-In of CHA PH2: Diasabled
Pull-In of CHA PH3: Enabled
Pull-In of CHA PH4: ----------
Pull-In of CHB PH1: Enabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Enabled
Pull-In of CHB PH4: -----------
CPU Voltage: 1.26250
CPU GTL Voltage Reference (0/2): .63
CPU GTL Voltage Reference (1/3): .67
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.18
DRAM Voltage: 2.14
NB Voltage: 1.22
NB GTL Reference: .67
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal
CPU Margin Enhancement: Performance
Hi mate,Quote:
Originally Posted by Leeghoofd
still no luck prime fails, first 1 and 3 and then 2 and 4.
For some reason I won't be able to boot without load line calibration enabled.
With load line calibration enabled, everest/cpu-z shows vcore 1.37v when in bios it's set to 1.35v.
Try OCCT and see if it is stable or use small ffts. I am perfectly stable but can not run large ffts.Quote:
Originally Posted by rusty
BIOS 1003 is officially posted for P5Q Deluxe, what are the changes in this one?
I wonder if its any better than 1102Quote:
Originally Posted by Dalten
I see that nice find man. It doesn't say does it. I wonder if since I'm on 1102 am I on newer one or? The because of the new option in this one will it cause issues going to the 1003 one?Quote:
Originally Posted by Dalten
ok will do that.Quote:
Originally Posted by truehighroller
What volts do use now for vcore and vtt ?
Don't use the 1003 IMO bcause I just tried and I lost my raid controller screen and it was saying hard drive in the boot order screen instead of the raid I have and I couldn't boot. I went back to 1102 now and I am fine again on my 3.8GHz. Here are my voltage settings.
CPU Voltage: 1.26250
CPU GTL Voltage Reference (0/2): .635
CPU GTL Voltage Reference (1/3): .635
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.32
DRAM Voltage: 2.02
NB Voltage: 1.28
NB GTL Reference: auto
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.60
man I can't get stable 3.8 no matter what I do.Quote:
Originally Posted by truehighroller
my vtt 1.32v-1.34v my vcore 1.33v-1.38v and still occt fails. Could it be NB ? or something else I miss?
seems like I have memory or nb problem cause occt comes up with code 4 in thread 0
Hmm yah, then you are deffinately having an issue. I am sorry that you are having bad luck.
:down: AHCI mode is broken in 1003 :down:
by the way do you use acpi 2.0 mode and AHCI mode ? I run sata ide+no acpi 2Quote:
Originally Posted by truehighroller
what about NB remmaping or something like that, do I need it or not ?
I still have 0702 bios on my p5q-deluxe... So with which bios version should i upgrade it? Many thanks ;)
Quote:
Originally Posted by sxs112
Is it still beta or will oficial release soon:cool:
Hey guys, I can´t take my Mushkin Redline over 1000Mhz, any try failing Super Pi after few seconds. I´ve been playing with skews (delay 150), vdimm (tried till 2.2V), vNB, higher PL...I don´t know what more to do. I´d like to put them at least at 1066. Any tip? Thanks
Is it just me, or is "DRAM Command Rate" non-existent in the BIOS? (I'm on 0803 right now)
Also, where do you guys find beta BIOSes for this board?
P.S.: I did notice ASUS posted up a new BIOS on their site, 1003, but I saw many many people getting problems with it, so I did not flash it. I'm still on 0803.
Beta BiosQuote:
Originally Posted by zork®
not sure that i have the same problem as you but i could not get it stabile on 475FSB. Only Vcore makes my setup more stabile....Quote:
Originally Posted by rusty
Yea, same here, just with high Vcore I can get stability at 500 FSB, I´m talking about 1.4V +
ok guys I just found out that when OV_CPU & OV_NB disabled system won't boot even with voltages below 1.7v like 1.33v for instance. Once changed to enabled able to oc again to 3.8ghz.
Well I guess I'm going to put more vcore then. Can anyone verify that load line calibration puts more voltage than needed? For example, I set vcore to 1.33v with load line calibration I get 1.35v
Pmp's quote : This option affects FSB signal, and it's here due to Intel recommendation. Basically it affects OC margin for upcoming, cheap Q8200. It _may_ enhance a little typical Yorkfields/Wolfdales as well.Quote:
Originally Posted by nex-3
Optimized setting enable/disable Compatible or Performance modes depends on CPU uCode.
If you don't have any probs with it Lewis, keep it....Quote:
Originally Posted by Lewis23
It overvolts a bit over the bios setting...Quote:
Originally Posted by rusty
Quote:
Originally Posted by petekol
Think you guys are more CPU limited then mobo/setting limited here... if you need as much Vcore to get anywhere... it's the CPU surpassing it's sweetspot... I have the same with one Xeon 3310, fine at 3.8ghz at 1.16Vcore (under load) but once over 4ghz I need almost 1.3volts to get it anywhere stable... CPU is capping out on me due to high temps... same mobo does 500FSB daily with an E8400@4ghz... only hardware change is the CPU... Will keep the Xeon at 3.6Ghz at 1.1 volts....:rolleyes:Quote:
Originally Posted by RBS
mate I'm running vcore 1.4v and vtt 1.32v dram 2.1v at 3.8Quote:
Originally Posted by Leeghoofd
prime's thread 3 fails others stay fine what should I up GTL ref or more vcore?
Hi Leeghoofd,
Unfortunately there is no way I can lower PLL and FSB term. voltage if I want to run stable at FSB444.
The only setting that I could lower was the DRAM voltage, and I need 2.02v.
Anything below that value will cause Prime Blend to fail.
I've tried changing memory timings like you suggested but it seems that I've hit a wall at FSB444 / RAM 1066MHz.
Now I'm running with the following settings, and still trying to lower FSB term. voltage.
Since I'm at 4GHz CPU clock, I don't know if I should try lowering CPU PLL with FSB400... :rolleyes:
AI Overclock tuner: MANUAL
CPU Ratio Setting: 10
FSB Frequency: 400
FSB Strap to North Bridge: AUTO
PCI-E Frequency: 103 (101 will cause my display driver to stop sometimes)
DRAM Frequency: DDR2-1066
DRAM CLK Skew on Channel A1: Normal
DRAM CLK Skew on Channel A2: Normal
DRAM CLK Skew on Channel B1: Normal
DRAM CLK Skew on Channel B2: Normal
DRAM Timing Control: MANUAL
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Enabled
DRAM Read Training: Disabled
MEM. OC Charger: Disabled
AI Clock Twister: Strong
AI Transaction Booster: MANUAL
COMMON PERFORMANCE LEVEL: 07
PULL-INS: Both 1&3 Enabled
CPU Voltage: 1.41250
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.28
DRAM Voltage: 2.02
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO
Load Line Calibration: ENABLED
CPU Spread Spectrum: DISABLED
PCIE Spread Spectrum: DISABLED
CPU Clock Skew : Normal
NB Clock Skew : Normal
CPU Margin Enhancement: Performance
What do you think about this setup?
Thank again for your precious help.
Quote:
Originally Posted by Leeghoofd
Rusty back down to 450FSB, hardly think it's mobo related... what are ya coretemps ? have you tried playing with one setting at a time ? most Q9450 users seem to need 1.6PLL and pretty high FSB Term voltage for 3.8Ghz ops... you can try to get with 6 multi as high FSB as you can... but I really think you got a mediocre performing CPU...
About my Mushkin problem, here is my config template:
JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: auto
FSB Frequency: 400
PCI-E Frequency: 101
DRAM Frequency: DDR2-1003
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: disabled
MEM. OC Charger: enabled
AI Clock Twister: AUTO
AI Transaction Booster: manual
Common Performance Level [7]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.2875
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.22
DRAM Voltage: 1.98
NB Voltage: 1.24
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO
Load Line Calibration: enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : auto
NB Clock Skew : auto
Advance CPU Settings
CPU Ratio Setting: 8
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
Thanks .
Looking good man, I never run static read control on, had too many issue with it... can you run an everest Ram bandwith test on this setup... wanna see the difference with my more moderate tweaks... this is my 24/7 setup :Quote:
Originally Posted by miguelca
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: Moderate
AI Transaction Booster: MANUAL
COMMON PERFORMANCE LEVEL: 08
here :> http://img144.imageshack.us/img144/7409/23ax2.jpgQuote:
Originally Posted by Leeghoofd
http://img144.imageshack.us/img144/7...69f982a0c4.jpg
I prefer load temps rusty, do the cores go over 60-65°C ?
http://img244.imageshack.us/img244/6647/24ft2.jpgQuote:
Originally Posted by Leeghoofd
http://img244.imageshack.us/img244/6...5dbca8b969.jpg
Hi Leeghoofd,
In about 1h-1h30m when I go home for lunch I'll post a screenshot of Everest Cache and Memory Benchmark.
DRAM Static Read Control used to work fine on my P5K Premium (with any FSB).
On the P5Q Deluxe it only works well with FSB400.
Anything above this will cause instability and sometimes the PC won't even boot.
BTW, what FSB/multiplier are you using?
Quote:
Originally Posted by Leeghoofd
did you unlock OV_CPU & OV_NB ?Quote:
Originally Posted by miguelca
Remote Desktop Connection sometimes comes in handy... :ROTF:
http://i267.photobucket.com/albums/i...yBenchmark.jpg
Quote:
Originally Posted by Leeghoofd
I suggest to disable all that unnecessary stuff on the taskbarQuote:
Originally Posted by miguelca
Yah that looks pretty :banana::banana::banana::banana:y man lol.Quote:
Originally Posted by rusty
defeats the purpose of benchmarking I guessQuote:
Originally Posted by truehighroller
Rusty what kind of memory do you have?
http://www.newegg.com/Product/Produc...82E16820148180Quote:
Originally Posted by truehighroller
Do the temps read low on the p5q-e 0610 bios?.Mine says 28c on windows now with my chip at 3.2ghz(400fsb) at 1.35vcore(stock for my chip i believe)
rusty, you guess wrong ;)
Just because I have 2 startup icons for my Brother printer (MFP), 1 for my soundcard, 1 for my Razer mouse, 1 for my Seagate external HDD, 1 for my bluetooth device, 1 for AnyDVD, 1 for Windows Mobile Device Center and 1 for my antivirus, it doesn't mean my benchmarks are affected.
You've probably noticed that Everest was running and showing temperatures too..
I can assure you that if I disable (exit from) all those icons, my benchmarks won't produce better results.
Believe it or not, all those icons are neccessary for my kind of computer usage and don't take more than 500Kb of my 4GB of RAM (ok 3.3GB actually on a 32Bit O.S.).
On the left side of my taskbar you can see a "big" quick-launch bar.
What do you think needs more resources, shortcuts on the desktop or shortcuts on the quick-launch? :D
Quote:
Originally Posted by rusty
I ain't talking about shortcuts. Antiviruses usually utilize some memory even if idle, normally you would have to delete it completely to fully stop it. Deactivating it won't do anything. other apps I guess you can leave me on.Quote:
Originally Posted by miguelca
Hey guys first post in this thread, checking in.
I am stable at 3.6ghz with a GO step q6600.
My VID is 1.3125 (1.313v)
Almost everything in the bios is auto right now with the exception of manual control over cpu multi & ram timings.
Vcore 1.425
Cpu Multi x8
FSB 455
Ram 1:1 5-4-4-12
Enabled the function to limit vdroop
Speed Step, C1E, Spread Spectrum. All that jazz is still on since I leave my computer on 24/7 and have had no stability issues so far.
Prime95 Stable, I am seeing max temps of 50c on the Tcase and ~70c for the 0&1 Cores and 60c for the 2&3 cores. I would like to keep 3.6ghz for my 24/7 settings but try to reach higher for benchmarks.
I figure following the general rule of +15% of your VID means I can "safely" put 1.5v into this cpu but others tell me here and there that thats too much. I was 3dmark06 and wprime stable @ 3.8ghz 1.47vcore but its not prime stable. But I have yet to mes with the GTL values or to disable some of the options known to cause instability in a high overclock.
First things first, whats the max safe temp under prime 95 I should look for using coretemp or speedfan for the cores & tcase?
Also was curious why this mobo has a x63 for 2 of the cores and a x67 for the other 2 cores under the GTL (or was it PLL lol) ratio... should they not be the same?
Rusty are you aware that for good superpi runs some benchers prefer the Luna windows XP desktop... I don't have many apps launching here... I try to keep my rig as clean as possible but for regular benchmarks (not chasing any records ) You won't notice much on a regular windows install with or without many apps loaded...Quote:
Originally Posted by rusty
If you want to grab every extra point, I suggest you to install a bench OS like most of us do... which is about 300-400megs for an XP install... almost no apps that eat resources, no internet explorer,...
I edited a bit your post 3.3vcore seems a bit much... as long as you can cool that CPU 1.5 is no prob for day to day running, I try to keep them cores under 65°C for 65nm, 60°C for 45nm... but you will have to tweak the settings for the mobo manually as you said most is on auto... these mobo's really do overvolt on the chipsets and that's not good...Quote:
Originally Posted by 古強者死神
For the PLL I keep them on auto most of the time... but many users use 0.63 for both...
You really got a good CPU with a VID that high that still can do 3.6ghz at 1.42 Vcore....
well let's not go that far :>Quote:
Originally Posted by Leeghoofd
anyways, did you see my post with full load ?
Yeah saw them Rusty, even with that much voltage they look reasonable... really puzzled with your CPU and my Xeon too as they seems to love voltage... and most of the others Q9450 them speeds that at 1.3ish level...
what are the reasonable full load temps in your opinion ?Quote:
Originally Posted by Leeghoofd
yeah I went back and edited that a moment ago. I had my son jumping up and down on me and caused some typos lol. 1.425 vcore bios 1.313VID for the cpu. Windows shows me 1.40 or 1.41v usually with no vdroop now that I have load line calibration enabled.
I noticed I was more stable with x67 for both of my PLL settings, atleast I thought I was as I had not been able to finish 3dmark06 before I tried that, but I think it increased the temps of my 2 hottest cores by yet another 5c. I mean thats what that setting does, its the divider for the voltage the cores get right?
If you say under 65c for the cores looks like I hit my max already. High end air cooling with a thermalright ultra 120 extreme cooled by a single 1600rpm s-flex. (tho hooked to the cpu fan header it only runs it near 15000rpm)
It has alot to do with my case I am sure. Antec P182SE GREAT case but definitely not a enthusiast super overclocker or dual card case as its incredibly quiet and has decent airflow but not high airflow since that entire upper chamber has only 1x120mm fan intake and that fan is behind a dust filter & a door. I do not notice cpu temp changes with those off but my dual 4850's drop 5c idle and 10c load just by opening that door and taking off that filter.
3.6ghz will carry me quite nice for most things, but I have a cpu bottleneck for 3dmark06 and probably a few other things too, so thats why I really wanted to get near that 4ghz limit.
About PL in 1102 + PULL-INS: 1&3 Enabled .... did anyone get PL=7 with 8*450fsb ?
Quote:
Originally Posted by jVIDIA
I couldn't no. Did you see the new bios on asus 1003? I lost my raid controller with it. I flashed back to 1102 now.
Leeghoofd,
I'm running Prime Blend now with the following setting:
AI Clock Twister: Stronger
I've benchmarked Cache and Memory with Everest before starting Prime, and I couldn't find any significative difference in R/W MB/s or latency.
Just want to know exactly how far I can go in what concerns memory performance with FSB400.
Can you kindly let me know what FSB/multiplier you're using? :)
P.S. Official BIOS 1003 sucks. Lots of problems with SATA device detection in BIOS. Asus should remove it from their website.
Not possible here, PL7@425 and PL8@450 still the best I can hit.Quote:
Originally Posted by jVIDIA
I never saw a difference between Strong/Stronger @ 400FSB either.Quote:
Originally Posted by miguelca
Just added one more manual setting put AI transaction booster to manual and then changed the common performance level to 10.
I did not see any change in my wprime time but I guess I would need a memory benchmark to really see the difference. Also my divider is 1:1. I thought 1:1 is always the most optimal for performance, but looks like from the bits and pieces I can see that a different divider may be better? I only have DDR2 800 memory so I dont think it will go too much higher and I consider myself lucky its stable at DDR2 910 with 5-4-4-12 (the epp profile, it defaults to 5-5-5-15 if not set manually tho)
Maybe you could try 400x9, strap 266, memory@1000 5-5-5-15, PL7. If that works for you, it'll have better memory latency.Quote:
Originally Posted by 古強者死神