DFI LP UT X58-T3EH8 - First bench, bios screens etc

Printable View

Show 100 post(s) from this thread on one page

05-29-2009, 08:29 PM
Paradoxxx

I would appreciate some assistance, I have an i7 920 D0 cooled with a Noctua and the motherboard in the topic. I have updated my BIOS to 05/28 or whatever the latest beta is on DFI's website.

I would like to be able to use the 21 multiplier, to achieve this I enable turbo mode. However enabling turbo mode also enables a 22 multiplier on Core 1 which can lead to instabilities. I just want 21 and not that pesky 22 which can arise at times.

I noticed by use of CPU-z that during some of my higher clocked stability tests that my CPU under clock by means of the multiplier. Is this a feature part of thermal throttling to prevent harm to the CPU? On load my CPU temp has not crossed 74C

What is the difference between Core Voltage and VTT? is the VTT the same as UnCore Voltage? Other than those two and DRAM voltages are there any other voltages I should be tweaking?

I would also appreciate any directions to guides, I am fairly inexperienced with this BIOS.
05-29-2009, 11:01 PM
Masami

Hi guys!! I'm very proud of this mobo but... it needs rma. My controller sata has some problem... every change of bios I've to disconnect the other hard disk (not that with os obviously) to have regular boot... Please help me
05-29-2009, 11:08 PM
devsk

Finally got my DFI board. Bunch of noob questions. Coming from Giga and Asus land, so pardon my ignorance.

1. How do I select a different disk for booting than the one selected in the BIOS without going into BIOS and POSTing twice? Its F8 in asus.

2. Should I leave VTT and VID Special Add at Auto? I just tested 200BCLK and I am going for 220. What does the Auto select?

3. What is OC shutdown free? Should it be enabled or disabled?

4. Set VR limit Current Limit Max, should it be enabled or disabled? I don't want the mobo to throttle me?

Thanks for your help.
05-30-2009, 12:47 AM
devsk

I am trying to run the same settings as my earlier mobo for 4.3Ghz and I am seeing throttling with multi dropping. The vcore is 1.34-1.36 (in cpuz) with vdroop disabled. vtt is 1.39-1.41 seen in h/w monitor.

What settings am I supposed to choose to disable throttling? I have ESIT enabled (needed for turbo), turbo enabled, CxE at Auto, Thermal mgmt Enabled, PPM (what is PPM?) enabled.
05-30-2009, 01:17 AM
devsk

More issues: While running prime, after 5 minutes, it was shutting the PC off although the temps were in lower 80s (it shut itself off right under my nose, I was watching the temps). So, I disabled the shutdown at 100C in BIOS. It can't even boot the damn thing. It displays 88 code. Reset and same thing.

Any ideas on what's shutting my PC? At the same temps (and higher), the same CPU was working fine in Asus board. It would lower the multi to 20x but it won't shut the PC Off like that.

This BIOS is really buggy. I can't get consistent results from it. I lowered the BCLK, it won't post. Is 02/17 the latest DFI BIOS for this board? I am surprised DFI hasn't released a BIOS in such a long time. I have a xeon w3520, so that might have something to do with strangeness. Certainly very arbitrary behavior. Haven't seen anything like it from giga or asus.
05-30-2009, 02:20 AM
eva2000
Nice clocks dj888u2 :)

For DFI UT X58 new board owners, here's some links you should bookmark and read and re-read particular 1st link as lots of the answers to the questions you posted (devsk and Pardoxxx)
w3520 work fine on DFI UT X58-T3EH8 using 4/28 pre-beta also found in bios change log link listed above

4000Mhz at 1.184v load = coretemp = 57-60c load temps in 26.5C ambients!

http://fileshosts.com/intel/DFI/DFI_...large_load.png
05-30-2009, 03:28 AM
Sam_oslo

w3520 work fine on DFI UT X58-T3EH8 using 05/08 beta too.

@4.01GHZ (211x19) HT:On, 1.15v, 11 hours primestable
http://img10.imageshack.us/img10/209...12hours.th.jpg

I have never tried 4/28 pre-beta. What advantages (compared to 05/08) you guys getting from this?
05-30-2009, 03:47 AM
eva2000

Quote:

Originally Posted by I34z1k

Code:

enie BIOS Setting CPU Feature Set VR Current Limit Max: Disabled Thermal Management Control: Disabled EIST Function: Disabled CxE Function: Disabled Execute Disable Bit: Disabled Virtualization Technology: Disabled ***** Logical Processor Setting ***** Intel HT Technology: Enabled Active Processor Cores: All DRAM Timing Channel Interleave Setting: Auto Bank Interleave Setting: Auto Memory LowGap: 1536M DRAM Command Rate: 1N CAS Latency Time (tCL): 8 RAS# to CAS# Delay (tRCD): 8 RAS# Precharge (tRP): 8 Precharge Delay (tRAS): 24 REF to ACT Delay (tRFC): AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): AUTO Row Cycle Time (tRC): AUTO Read CAS# Precharge (tRTP): AUTO Four ACT WIN Time (tFAW): AUTO Voltage Setting O.C. Shut Down Free: Enable O.C.S.D.F CPU VID Control: 1.4250V Power Saving: Standard Super Vid: OFF Vcore Auto PSI: Disabled OCP: 140A DRAM Bus Voltage: 1.650V DRAM PWM Switch Frequency: Nominal DRAM PWM Phase Control: 2 Phase Operation CPU VTT Special Add: AUTO CPU VTT Voltage: 1.45v VTT PWM Switch Frequency: Nominal Frequency VTT PWM Phase Control: 2 Phase Operation CPU PLL Voltage: 1.80v IOH/ICH 1.1V Voltage: 1.35v IOH Analog Voltage: 1.15v ICH 1.5 Voltage: 1.5v ICH 1.05V Voltage: 1.05v DIMM 1/2 DQ/DQSTB Bus VREF: -00.0% DIMM 3/4 DQ/DQSTB Bus VREF: -00.0% DIMM 5/6 DQ/DQSTB Bus VREF: -00.0% x DIMM 1/2 ADDR/CMD Bus VREF: 110 x DIMM 3/4 ADDR/CMD Bus VREF: 110 x DIMM 5/6 ADDR/CMD Bus VREF: 110 CPU QPI Drive Strength: Strong IOH QPI Drive Strength: Normal Exit Setup Shut down: Mode 2 O.C. Fail Retry Counter: Enabled O.C. Fail CMOS Reload: Disabled PPM Function: Disabled Turbo Mode Function: Disabled 1 core Max Turbo Ratio: 22x 2 core Max Turbo Ratio: 21x 3 core Max Turbo Ratio: 21x 4 core Max Turbo Ratio: 21x CPU Non-Turbo Clock Ratio: 20x * BCLK/UCLK/QPI Controller Settings * QPI Control Settings: Enabled QPI Link Fast Mode: Enabled QPI Frequency: 4.800GT/s(BCLK*18*2) CPU Base Clock (BCLK): 200 Mhz Boot Up CPU Base Clock: AUTO PCIE Clock: 105 Mhz DRAM Frequency: BCLK*8 1200MHz UnCore Frequency: BCLK*16 3200MHz CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled

Unfortunately DFI DK X58 slightly different so settings used on DFI UT X58 aren't exactly the same. Never used DK X58 so can't really comment. But set vr limit max = enabled to disable all thermal/current protection limits if you want to overclock and IOH/ICH 1.1V Voltage: 1.35v a tad high you really don't need more than 1.11v to 1.23v on air/water

Not sure on DK X58, but on UT X58, for D0 stepping cpus O.C. Shut Down Free: disabled is more stable than enabled. But for C0 stepping enabled was better than disabled.
05-30-2009, 04:01 AM
I34z1k

Thanks, will try that and keep fiddling :)

I'd heard the boards were very similar so i thought it was worth a bash :)
05-30-2009, 04:11 AM
eva2000

Quote:

Originally Posted by Sam_oslo

w3520 work fine on DFI UT X58-T3EH8 using 05/08 beta too.

@4.01GHZ (211x19) HT:On, 1.15v, 11 hours primestable
http://img10.imageshack.us/img10/209...12hours.th.jpg

I have never tried 4/28 pre-beta. What advantages (compared to 05/08) you guys getting from this?

change log list http://i4memory.com/f80/dfi-ut-x58-t...nge-log-13966/ 4/28 is 05/08 minus the non-rtl/tref/elpida skew mod changes i.e. without raid card improvements etc
05-30-2009, 06:13 AM
eva2000

For folks with win7 OS and turbo 12x fixed multi issue, some reading http://i4memory.com/f80/windows-7-tu...esearch-18053/ feedback would be nice :)

Quote:

CPU Feature
Set VR Current Limit Max: Enabled
Thermal Management Control: Disabled
EIST Function: Enabled
CxE Function: AUTO
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

Voltage Setting
O.C. Shut Down Free: Disable O.C.S.D.F
CPU VID Control: AUTO
CPU VID Special Add Limit: Enabled
CPU VID Special Add: 110.10%
Vcore Droop Control: Disabled

PPM Function: Enabled
Turbo Mode Function: Enabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

With CxE set to AUTO instead of Disabled, 21x multi under load achieved BUT idle cpuz reported multi is funny one 22x! Under load multi changes from 22x idle to 21x load and voltage changes from 1.120v idle to 1.312v load

http://fileshosts.com/intel/DFI/DFI_...xe_enabled.png

http://fileshosts.com/intel/DFI/DFI_...d_hpi_load.png

As per i7 Turbo Tool and RealTemp author's explanation, the calculated multiplier is more accurately depicting Turbo status ONLY under load and can vary at idle. It seems with CxE enabled, Turbo mode 21x multi is fully engaged only under load. At idle no idea what CPUZ is thinking LOL
05-30-2009, 09:09 AM
hel_19

http://images.orkut.com/orkut/photos...q46TUkFg6d.jpg

3,6ghz 1,4v
3,8ghz 1,5v

bad processor?
05-30-2009, 10:01 AM
devsk

At 21x190, 1.3vcore, 1.35vtt: one of the temps shown by h/w monitor reaches 84C under linx load, while all cores are below 80C. What temperature is that? Its marked as TMPIN1.
05-30-2009, 10:12 AM
devsk

Just installed smart guardian. It seems like the temp that I talked about is SYSTEM temperature. Is that VRM temp? Why is it getting to 84C under load? Is it because I haven't installer the flame freezer or whatever? The reviews I read showed only 2-3C difference between installing it and not installing it. I have push-pull setup and a panaflo doing a good job at 2700 rpm of dispensing heat and cores stay under 80C. Any ideas what I need to do to get that VRM cooled down?

How high the VRM can go?
05-30-2009, 11:18 AM
I34z1k

Got turbo working on my t3eh6 with your guide. Didn't work before.
05-30-2009, 11:36 AM
dj883u2
Quote:
Originally Posted by eva2000

Nice clocks dj888u2 :)

For DFI UT X58 new board owners, here's some links you should bookmark and read and re-read particular 1st link as lots of the answers to the questions you posted (devsk and Pardoxxx)

DFI UT X58-T3EH8 notes, findings & tips
Intel Core i7 920 Overclocking Introduction Guide on X58
Prime95/LinX/Super Pi 32M stability tweaks
DFI UT X58 - tRRD, RTL, tFAW timing discussion.
DFI Lanparty UT X58-T3EH8 LGA1366 Photos, Bios and Overclocking Information Guide
DFI LP UT X58-T3EH8 - Bios Template
DFI UT X58-T3EH8 - Bios Download / Change Log
DFI LP UT X58-T3EH8 - Bios Screenshots
Memtest86+ (v2.11)
First i7 920 D0 Step = mixed bag of results
Second i7 920 D0 Stepping 3851A368 #2 results

w3520 work fine on DFI UT X58-T3EH8 using 4/28 pre-beta also found in bios change log link listed above

4000Mhz at 1.184v load = coretemp = 57-60c load temps in 26.5C ambients!

http://fileshosts.com/intel/DFI/DFI_...large_load.png
Thank you very much!:)

Prime95 - 201x21 "4221Mhz" - V.core 1.21v:

http://img46.imageshack.us/img46/4342/37239209.th.jpg

Good stable motherboard.:up:
05-30-2009, 01:15 PM
eva2000

Quote:

Originally Posted by dj883u2

Thank you very much!:)

Prime95 - 201x21 "4221Mhz" - V.core 1.21v:

http://img46.imageshack.us/img46/4342/37239209.th.jpg

Good stable motherboard.:up:

wow one nice w3520 you have :) ambient temps ?

Quote:

Originally Posted by devsk

Just installed smart guardian. It seems like the temp that I talked about is SYSTEM temperature. Is that VRM temp? Why is it getting to 84C under load? Is it because I haven't installer the flame freezer or whatever? The reviews I read showed only 2-3C difference between installing it and not installing it. I have push-pull setup and a panaflo doing a good job at 2700 rpm of dispensing heat and cores stay under 80C. Any ideas what I need to do to get that VRM cooled down?

How high the VRM can go?

yes SYSTEM reported temp in SG = PWM temps - see here for ideas and why it's hot http://i4memory.com/f80/t3eh8-very-h...m-temps-18015/ and tip #31 and #32 here http://i4memory.com/102537-post3.html

Quote:

Originally Posted by I34z1k

Got turbo working on my t3eh6 with your guide. Didn't work before.

Thanks for the feedback :) Yeah CxE = C1 fixed 21x at idle/load for my W3520

FIXED idle and load 21x multi!

Change CxE from AUTO/Disabled to C1E.

==================================================

Quote:

CPU Feature
Set VR Current Limit Max: Enabled
Thermal Management Control: Disabled
EIST Function: Enabled
CxE Function: C1E
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

Voltage Setting
O.C. Shut Down Free: Disable O.C.S.D.F
CPU VID Control: AUTO
CPU VID Special Add Limit: Enabled
CPU VID Special Add: 110.10%
Vcore Droop Control: Disabled

PPM Function: Enabled
Turbo Mode Function: Enabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

http://fileshosts.com/intel/DFI/DFI_...1e_enabled.png

http://fileshosts.com/intel/DFI/DFI_...abled_load.png

Max calculated and MSR multi = 21x under 3dmark06 load

http://fileshosts.com/intel/DFI/DFI_...d_3dmark06.png
05-30-2009, 01:50 PM
devsk

Is the flame freezer supposed to be loose after installing the inner mounting clip? Its very loose after tightening the screws really hard. It can't be pushed any further inside because the inner fins are blocking it now.
05-30-2009, 01:52 PM
dj883u2

Ambient temps is 25°.:)
05-30-2009, 02:01 PM
devsk

And as expected, temps at 84C after 4 mins of linx...:( man, this thing is not going anywhere.
05-30-2009, 02:06 PM
devsk

crazy part is that the NB temps v never go beyond 40c
05-30-2009, 03:00 PM
devsk

Can someone please give me the hotkey for changing boot order without going into the BIOS? Please.
05-30-2009, 03:02 PM
eva2000

Quote:

Originally Posted by devsk

Is the flame freezer supposed to be loose after installing the inner mounting clip? Its very loose after tightening the screws really hard. It can't be pushed any further inside because the inner fins are blocking it now.

less loose = use tim on flame freezer as per tip #32 http://i4memory.com/102537-post3.html

Quote:

Originally Posted by devsk

And as expected, temps at 84C after 4 mins of linx...:( man, this thing is not going anywhere.

ways to reduce pwm temps http://i4memory.com/f80/t3eh8-very-h...m-temps-18015/

Quote:

Originally Posted by devsk

Can someone please give me the hotkey for changing boot order without going into the BIOS? Please.

ESC
05-30-2009, 03:22 PM
The Water Dog

Doing some testing with my memory:

http://i39.tinypic.com/2mrxkk5.jpg

And diffrence between 1600 and 2000:

http://i43.tinypic.com/255kf8w.jpg

http://i41.tinypic.com/aw4a6b.jpg
05-30-2009, 05:03 PM
Paradoxxx

What are your opinions on Vcore Drop?

# Vcore Droop: For Vcore droopage, according to CPUZ v1.49:

* Vdroop Enabled = 0.016-0.032v droopage under load
* Vdroop Disabled = 0.00-0.008v droopage under load

To me I expected that it should be disabled, resulting in more stable voltages however in practice I achieve more stable OC's with it on. Please explain.
05-30-2009, 05:20 PM
Ice009

Quote:

Originally Posted by Sam_oslo

NorthQ 3590 Water Cooling Kit with 4x1200RPM push/pull was the last one, (and it was making a good deal av turbulent and noise), but and it was running 3 to 5'C cooler than Noctua NH-U12P 2x1200RPM push/pull (which i used before that) on my good old i7 C0 (which was a good deal cooler than w3520 with the same Vcore).

Prolimatech Megahalems with 2x1200 RPM Push/Pull, has worked best for me so far. It is running this hot w3520 about 6-10'C cooler than the NorthQ 3590.

Thanks for the info. I'm going to use Air Cooling when I upgrade to i7 and I want to ask how much better the Prolimatech Megahalems would be than a Noctua NH-U12P or TRUE? Is it much better or only a couple of degrees better? I've already got both the Noctua and TRUE, but would it be worth getting the Megahalems instead? btw does it come with two sets of fan clips?

Also, what is is like to mount compared to a TRUE or Noctua?
05-30-2009, 05:50 PM
ColonelCain

To anyone having issues getting VMware running:
Head on over to this link: http://communities.vmware.com/docs/DOC-8978

The problem is, is that DFI leaves the "VT" flag "Unlocked", so even though you set Virtualization Tech. to "Enabled" in the bios, Windows switches it to "Disabled" on log-in.
05-30-2009, 05:56 PM
RobPuba

DFI Board is Rock Solid !

:up:Just have to update my my signature.......... i7 920:up: Batch is 3849A925. At The time running windows 7.
05-30-2009, 09:04 PM
devsk

I need some help. I think I am stuck at BCLK of 200. Anything higher just freezes and resets the system. Here are my settings:

cpu feature: VR enabled, Thermal disabled, CxE C1E, Execute disable Bit enabled, VT enabled, HT enabled, All cores
ram: rated timings. 2:6, so its running slower than rated.
voltages: vcore 1.3 (tried upto 1.35), vid special add enabled, special add Auto, vdroop disabled, dram 1.65, vtt 1.36 (tried upto 1.45), VTT special add Auto, CPU pll 1.8 (tried upto 1.9), IOH/ICH 1.11 (tried upto 1.31), IOH analog voltage 1.1 (tried upto 1.15). Rest default.
PPM enabled.
Turbo enabled.
BCLK 202
PCIE 100
DRAM Freq BCLK*6 (1212)
UnCore Freq BCLK*14.

Rest default.

Any ideas what's up? The CPU is definitely capable because I was running 4.32Ghz (21x206) on Asus with the same hardware. I was using 1.35Vcore, 1.38VTT, 1.3IOH, 1.84PLL for 4.32Ghz.
05-31-2009, 12:01 AM
eva2000
Quote:

Originally Posted by devsk

I need some help. I think I am stuck at BCLK of 200. Anything higher just freezes and resets the system. Here are my settings:

cpu feature: VR enabled, Thermal disabled, CxE C1E, Execute disable Bit enabled, VT enabled, HT enabled, All cores
ram: rated timings. 2:6, so its running slower than rated.
voltages: vcore 1.3 (tried upto 1.35), vid special add enabled, special add Auto, vdroop disabled, dram 1.65, vtt 1.36 (tried upto 1.45), VTT special add Auto, CPU pll 1.8 (tried upto 1.9), IOH/ICH 1.11 (tried upto 1.31), IOH analog voltage 1.1 (tried upto 1.15). Rest default.
PPM enabled.
Turbo enabled.
BCLK 202
PCIE 100
DRAM Freq BCLK*6 (1212)
UnCore Freq BCLK*14.

Rest default.

Any ideas what's up? The CPU is definitely capable because I was running 4.32Ghz (21x206) on Asus with the same hardware. I was using 1.35Vcore, 1.38VTT, 1.3IOH, 1.84PLL for 4.32Ghz.

Again re-read links posted at http://www.xtremesystems.org/forums/...postcount=1106 has all you ever need - besides me holding your hand :) j/k

From 2nd link posted at http://www.xtremesystems.org/forums/...postcount=1106 you can see why you're having problems as optimal/stable Uncore to DRAM frequency ratio needs to be 2:1 so Uncore multi needs to be 2x DRAM multi, so 6x mem multi needs uncore multi at 12x and not 14x. This is also mentioned in first link thread at http://www.xtremesystems.org/forums/...postcount=1106 under tip #24 http://i4memory.com/102537-post3.html

As to the rest, will depend on what your particular cpu's bclk to cpu vtt ratio relationship is like - #2 and #3 http://i4memory.com/102537-post3.html.

My latest result, no probs pushing higher for me on 21x with W3520 now after working around 12x fixed turbo issue which seems to only effect my W3520 but not my 4x i7 920 cpus. i7 Turbo says max Calculated and MSR multi is 21x under load and 3dmark06 cpu score confirms it is working at 21x210Bclk with VID = AUTO + VID Special Add = 110.1% for 1.088v idle and 1.312v load vcore when CxE set to C1E.

CPUZ Idle vs After Load Idle

max Calculated and MSR multi is 21x

http://fileshosts.com/intel/DFI/DFI_.../cpuz_idle.png http://fileshosts.com/intel/DFI/DFI_...tload_idle.png

3dmark06

max Calculated and MSR multi is 21x

http://fileshosts.com/intel/DFI/DFI_...7_1312v_tn.png

Added another useful link to my list for DFI UT X58 for turbo multi and win7
05-31-2009, 12:25 AM
eva2000

New thread for part 2 http://www.xtremesystems.org/forums/...d.php?t=225887
05-31-2009, 10:17 AM
devsk

Quote:

Originally Posted by eva2000

Again re-read links posted at http://www.xtremesystems.org/forums/...postcount=1106 has all you ever need - besides me holding your hand :) j/k

From 2nd link posted at http://www.xtremesystems.org/forums/...postcount=1106 you can see why you're having problems as optimal/stable Uncore to DRAM frequency ratio needs to be 2:1 so Uncore multi needs to be 2x DRAM multi, so 6x mem multi needs uncore multi at 12x and not 14x. This is also mentioned in first link thread at http://www.xtremesystems.org/forums/...postcount=1106 under tip #24 http://i4memory.com/102537-post3.html

I thought it was supposed to be greater than equal to 2x. I had been running 2:6 and 16x on my Asus mobo without any issues.

I will try the 12x.
05-31-2009, 10:24 AM
devsk

Are green slots the 2+4+6 you mention in your tips or are they the ones marked DIMM_2/4/6 on the motherboard?
05-31-2009, 10:53 AM
devsk

Ok, set it 12x and BSOD again within seconds of LinX. I removed the 2 modules out of 3x2GB and ran Linx for half hour fine. So, what gives? This ram was rock stable with Asus board.
05-31-2009, 11:13 AM
RobPuba

Best !

This is the best board I ever owned........ DFI Rocks:up::up::up:
05-31-2009, 12:37 PM
devsk

Quote:

Originally Posted by RobPuba

This is the best board I ever owned........ DFI Rocks:up::up::up:

ironic, how this is the worst for me so far. I am not sure if I am dealing with a dud.
05-31-2009, 01:28 PM
The Water Dog

Devsk: I had to buy another memory-brand to get the beast in this mobo out, and if you have the right memory..this board can do some serious damage:D
Do you have other memory you can try?
And you should read Eva2000 Dfi X58 tips=)
The green slots you should use.

RobP: Yeah, this is one of the best mobo i have tried. On the memory it is one of the best. Just 100% fun to play with.
2000mhz on 7-7-7-20 with 1,28vtt and 1.61vdimm.......
05-31-2009, 01:48 PM
hel_19

Quote:

Originally Posted by ColonelCain

To anyone having issues getting VMware running:
Head on over to this link: http://communities.vmware.com/docs/DOC-8978

The problem is, is that DFI leaves the "VT" flag "Unlocked", so even though you set Virtualization Tech. to "Enabled" in the bios, Windows switches it to "Disabled" on log-in.

thanks a lot :up:

http://img188.imageshack.us/img188/7456/cpu32535.jpg

I did not obtain 4ghz, which will be the problem?
06-27-2009, 02:00 AM
The Water Dog

Is there someone that have i picture of DFI LP UT X58-T3EH8 naked?
I have one that will see if its possible to make a full sb\nb block to this board:D
06-27-2009, 03:23 AM
rioja

before

http://img194.imageshack.us/img194/9721/img0363p.th.jpg

and after :rolleyes:

http://img189.imageshack.us/img189/5223/82388643.th.jpg
06-27-2009, 03:39 AM
The Water Dog

Rioja: Thank you very much:D
And nice watercooling;)

Show 100 post(s) from this thread on one page