Thinking of replacing the 120mm x 120mm x 25mm fan on my ZeroTherm Zen FZ120 with same size fan but with more CFM. Current spec is 1800 RPM, 60CFM and 31 dBA. Looking at Scythe S-Flex SFF21G Fluid Dynamic Bearing that is 1900 RPM, 75 CFM and 34 dBA. Will that extra CFM make a huge difference in load temps that are maxing at 54C/52C?
http://img242.imageshack.us/img242/2...nd3h24mct4.jpg
By bluestang
blustang nice OC,and yes it will improve a little.can you use two in push-pull with you cooler? thats what i do and it helps, brings it down 3-4c.
I get no beep codes at all. My computer just power cycles over and over. It won't even get to bios screen.Quote:
Originally Posted by sethk
All of those fail for me. No matter what settings, if I have 2 sticks of ram in the mobo, it bootloops. If I have 1 stick, it fires right up.Quote:
Originally Posted by Max25
This is pissing me off. I have a rev1 and a rev 1.1 it does the same thing on both of them. Rev 1 was on f5 bios. rev 1.1 is now on f6 bios.
Settings right now, Linksys is working. I'll post one up in a sec of it not working.
http://i154.photobucket.com/albums/s...tings333x9.jpg
That's a mystery I'm starting to believe this board doesn't like G.Skill's and Crucial so much especially low rated ones (below PC2_8500).Quote:
Originally Posted by clo007
I got 5 sets of ram: 2x2gig GSkill Pi 8800s, 2x2gig GSkill Black Pi 6400s, 2x1 gig GSkill 6400 HZs, 2x1gig Crucial Ballistixs 6400s double-sided, and 2x1gig Crucial Ballistixs single sided 2.2 volt.
I get the same thing with all 5 sets, so i know it's not the ram, it's something with the damn motherboard.
BIOS F8a is doing wonders for me. So far this is the lowest voltage it's taken me to get 485 stable.
http://img145.imageshack.us/img145/1218/485nb3.jpg
Code:MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio .......................: 6x
Fine CPU Clock Ratio...................: +0.0
CPU Frequency .........................: 2.91GHz (485x6)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 485
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 0mV
PCI Express Clock Drive................: 0mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: [Auto]
(G)MCH Frequency Latch.................: [333MHz]
System Memory Multiplier ..............: [2.00B]
Memory Frequency (Mhz) ................: 970
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15
Advanced Timing Control -> alles auf Auto
Channel A
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Channel B
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
CPU Vcore...................1.250v : 1.250v
CPU Termination...........1.200v: 1.30v
CPU PLL.......................1.500v: 1.570v
CPU Reference.............0.760v: .848v
MCH/ICH
MCH Core.....................1.100v: 1.360v
MCH Reference............0.760v.: .863v
MCH/DRAM Ref..........0.900v.: [AUTO]
ICH I/O........................1.500v: [AUTO]
ICH Core......................1.100v: [AUTO]
DRAM
DRAM Voltage...................1.800v.: [AUTO]
DRAM Termination ......................: 0.900V [AUTO]
Channel A Reference....................: 0.900V [AUTO]
Channel B Reference ...................: 0.900V [AUTO]
Advanced Settings
Limit CPUID Max. to 3..................: [Enabled]
No-Execute Memory Protect..............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support...................: [Disabled]
x C4/C4E State Support.................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Enabled]
CPU EIST Function......................: [Disabled]
Virtualization Technology..............: [Enabled]
Anyone used this ram? Will be using 32bit XP and am on a tight budget right now. Thanks
http://www.newegg.com/Product/Produc...82E16820134586
Radaja, thanks on the OC. Much of your info along with PangingIII, Zodden, Ghostleader and others made it happen. Thanks to all. Now to tweak more, especially if I could get ram to 1:1 at 550 FSB would be great, but I don't think it will happen.Quote:
Originally Posted by radaja
No, push/pull on that cooler is not possible. Also using Arctic Silver Ceramique paste.
I haven't heard people talk about Kingston in years as being good stuff. The hot stuff now is G.Skill and Corsair. Personally if I was to get some new memory now I'd get the Corsair PC8500 2x1gb Dominators w/fan for $19.99 after rebate. I know that was really good stuff a while back but that price is hard to pass up now. Of course there is a $40 rebate or so.
If you don't want the rebate spend a few dollars more and get the $34 G.Skill PC8500. The PC6400 G.Skill is probably the best selling stuff out now.
i have this 2.40b bug too. I'm stucked @ 535 right now everything above gives me errors in the mem test but i don't think it's the fault of my ram. Can boot in windows +550.
Ok, I might have gotten the Linksys thing solved...I think I was running my memory at 1.8v @ 1100 and it wasn't happy with that. I'm at 375x9 now with the memory at 2.14 and Vcore at 1.25. Orthos is running so we'll see what happens.
Can anyone explain exactly what the memory timings do? I've got mine on 2.66C right now I think. What are the numbers and A-D? Are there some settings that are better/worse?
You want to run your memory on the 266, 333 strap to get the best peformance out of your memory and computer, run memtest 86, and see if you can pass test 5, 7.
Quote:
Originally Posted by radaja
so how you like the q9650 so far?
could you try and see if the Vcore value at bios is set to "Normal" then how far can you overclocked this cpu?
try booting 400x9 and then bump up CPU FSB to 410.. 420... 425?
pangingII,do you mean set the vcore to default value of 1.20 and then up the fsb to see how far it will go on those volts?and yes to answer your question I LOVE THIS CPU! great temps but i didnt get a golden cpu with super low volts though.but that is ok the volts required for decent OC's are about normal.
sorry nope i meant don't enter core voltage value itself but set it to "Normal" (next selection from Auto), enable LLC and disable CPU C1E and EIST functions.Quote:
Originally Posted by radaja
may be try CPU core: Normal, CPU PLL: 1.50, CPU VTT: 1.24, NB: 1.34, and then from this setting try booting 400x9... and see if you able to get into Windows at 420-430x9?
pangingIII,i just tried that with 420x9 and it booted just fine.i used cpu-normal,vtt-1.26,pll-1.50,mch-1.30,ill test it for a few minutes to quickly test stability
I feel your pain clo007. What has gigabyte tech support said? anything? Your having a strange problem. It's happened twice to you and one other time to someone else it looks like.... but those are the only three cases i've heard of. I wish i had an answer for ya. I've had 2 of these boards myself and built a couple of systems for customers with it (well the ud3p version) and all work with 2 or all 4 dimms populated. Maybe theres a bug with the r series? i dunno.... Good luck :shrug:Quote:
Originally Posted by clo007
Edit: i see the other issue i was speaking of like yours was with a UD3P board, but i dont know how many different sticks he's tried. He could actually have bad ram.
pangingIII,here you go 420/425/430x9.also quick question what is the lowest pl using the 5:6 div under 450fsb?http://i43.tinypic.com/nlsx7k.jpghttp://i40.tinypic.com/1zg46k4.jpghttp://i39.tinypic.com/2zrq2he.jpg
430x9 is very nice, for me 3.8GHz is pretty fast already.Quote:
Originally Posted by radaja
i think PL 8 is the best you can do with the 430x9 and 4x 1GB 5-5-5-15 ram at 2.40B (or 5:6), and PL 8 also for 2.50A (4:5),
PL 7 for 2.66D (3:4).
and PL 6-7 for 3.0A (2:3) but this will need to run ram at 4x 1GB DDR2-1290, how much vdimm that you feel comfortable to put through your ram kits?
http://img165.imageshack.us/img165/9...lcondk5.th.jpg
Code might not be 100% accurate regarding the ram advanced timings (copied and pasted), but everything is auto except standard timings and PL. Still tweaking.
F8a bios seems better than F7a. But it takes longer for RAID to initialize. Instead of 2 dots, it's 9 dots. I hope to decrease my cpu voltage even more. Funny I can run the CPU VTT/PLL @ Normal @ 4ghz.
Code:MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio .......................: 9x
Fine CPU Clock Ratio...................: +0.0
CPU Frequency .........................: 4.05GHz (450x9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 0mV [Default]
PCI Express Clock Drive................: 0mV [Default]
CPU Clock Skew (ps)....................: 0ps [Default]
MCH Clock Skew (ps)....................: 0ps [Default]
DRAM Performance Control
Performance Enhance....................: [Standard]
Extreme Memory Profile (X.M.P.)........: [Auto]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: [2.00D]
Memory Frequency (Mhz) ................: 900
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time.......................: 4
tRCD ..................................: 4
tRP'...................................: 4
tRAS...................................: 12
Advanced Timing Control ->
Channel A
Static tRead Value.....................: 8
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Channel B
Static tRead Value.....................: 8
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
CPU Vcore...................1.250v : [1.350v]
CPU Termination...........1.200v: [Normal]
CPU PLL.......................1.500v: [Normal]
CPU Reference.............0.760v: [Normal]
MCH/ICH
MCH Core.....................1.100v: [1.3v]
MCH Reference............0.760v.: [Normal]
MCH/DRAM Ref..........0.900v.: [Normal]
ICH I/O........................1.500v: [Normal]
ICH Core......................1.100v: [Normal]
DRAM
DRAM Voltage...................1.800v.: [2.0V]
DRAM Termination ......................: 0.900V [Normal]
Channel A Reference....................: 0.900V [Normal]
Channel B Reference ...................: 0.900V [Normal]
Advanced Settings
Limit CPUID Max. to 3..................: [Enabled]
No-Execute Memory Protect..............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support...................: [Disabled]
x C4/C4E State Support.................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Enabled]
CPU EIST Function......................: [Disabled]
Virtualization Technology..............: [Enabled]
Well, i think i got my stability as well. Finally!!!
http://i11.photobucket.com/albums/a1..._orthos_3h.jpg
The only issue was i can`t leave my tRAS on 15 just on auto that give 23... But anyway is ok for now. I will test more soon.
Yes, this is royally pissing me off. I have like $500 worth of ram that none will work with 2 sticks.Quote:
Originally Posted by nugzo
Hi there everyone
I have just joined and am having real problems clocking my E6600 with this board. I managed 3.4Ghz stable with my old Abit IP35 but this just will not run stable at all.
I managed to get it to boot at 440fsb but orthos was not stable. So I lowered the fsb but then it got into a reboot loop!?
My spec is-
E6600
GA-EP45-UD3P
4GB G.Skill PC2-8500C5
OcUK 8800GTX
X-Fi Music
2x 320GB WD Blues in RAID0
Samsung SATA 22xDVDRW
Corsair HX620
All watercooled in a NZXT Lexa case
I have gone back to standard settings for the moment, but this is what I managed to get it running and booting into windows with.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 8
Fine CPU Clock Ratio...................: N/A
CPU Frequency .........................: 3.52 GHz (440X8)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 440
PCI Express Frequency (Mhz) ...........: 101
C.I.A.2 ...............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 800mV
PCI Express Clock Drive................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance....................: [Std]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [333MHz]
System Memory Multiplier ..............: 2.4B
Memory Frequency (Mhz) ................: ?
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15
Advanced Timing Control
tRRD...................................: Auto
tWTR...................................: Auto
tWR....................................: Auto
tRFC...................................: Auto
tRTP...................................: Auto
Command Rate (CMD) ....................: Auto
Driving Strength Profiles
Driving Strength ......................: Auto
Channel A
Static tRead Value.....................: [AUTO]
tRD Phase0 Adjustment..................: [AUTO]
tRD Phase1 Adjustment..................: [AUTO]
tRD Phase2 Adjustment .................: [AUTO]
tRD Phase3 Adjustment..................: [AUTO]
Trd2rd(Different Rank).................: [AUTO]
Twr2wr(Different Rank).................: [AUTO]
Twr2rd(Different Rank).................: [AUTO]
Trd2wr(Same/Diff Rank).................: [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Channel B
Static tRead Value.....................: [AUTO]
tRD Phase0 Adjustment..................: [AUTO]
tRD Phase1 Adjustment..................: [AUTO]
tRD Phase2 Adjustment .................: [AUTO]
tRD Phase3 Adjustment..................: [AUTO]
Trd2rd(Different Rank).................: [AUTO]
Twr2wr(Different Rank).................: [AUTO]
Twr2rd(Different Rank).................: [AUTO]
Trd2wr(Same/Diff Rank).................: [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enable]
CPU Vcore..............................: 1.46250v
CPU Termination........................: [Auto]
CPU PLL................................: [Auto]
CPU Reference..........................: [AUTO]
MCH/ICH
MCH Core...............................: 1.2V
MCH Reference..........................: [Auto]
MCH/DRAM Ref...........................: [AUTO]
ICH I/O................................: [Auto]
ICH Core...............................: [Auto]
DRAM
DRAM Voltage...........................: 2.1v
DRAM Termination ......................: [AUTO]
Channel A Reference....................: [AUTO]
Channel B Reference ...................: [AUTO]
I would love to get a nice high fsb and lower the multi, but just to get anything stable would be good!
Anyone offer any advice? I see most people are on Q9xxx or E8xxx but this is a good chip and dont really want to splash out on a new one when I should get this to 3.4+
Thank you for your help guys :up: