**Gigabyte GA-X58A-UD7 OC-Tips-Bios-Discussion Thread**

Quote:

---

Originally Posted by SteveRo

Mr mbreslin, nice work!
What do you have your vdroop compensation set to, if on setting 2 - voltages can go up under load - you can see it in cpu-v if you watch carefully.
pcmv run?


What do folks recommend here for 24/7 - no vdroop or setting 1?

---

Intel is clear, and recommending standard, but for some reason that gives too much vdroop on GB, at least much more than DFI.

I've been using 1 for a long time and it has been working fine for me, both with w3520 and X5650.
I've used 2 for a short time, but have been getting random BSOD at idle. I'm not sure if that was the reason, but it diapered after I changed to 1.


Intel has increased the CPU PLL for 32nm, and I'm still experimenting with it but can't see why and what kind effect it has on 24/7 stability, yet. Any experiences with this?

Intel has increased the CPU PLL for 32nm - what is the max now - 2v?
I have been benching many hours at 1.9v - linx stable up to 4.8 ht off.

1.9 pll seems to be what I need to be stable with 1.38 vcore/vtt. What was intel's pll max for 45nm?

Lsdme - what I wrong with @bios for flashing - I have used it many times on multiple ggbt boards - no problem.

Quote:

---

Originally Posted by SteveRo

Intel has increased the CPU PLL for 32nm - what is the max now - 2v?
I have been benching many hours at 1.9v - linx stable up to 4.8 ht off.

---

Yes the max CPU PLL is 2.0v for 32nm, but I can't see how it is effecting the 24/7 stability. I'm still experimenting, but have tried from 1.5v to 1.88v and all seams to be the same. Wondering how it is effecting on other OC.

Mr mbreslin - regarding the north bridge silent pipe - I haven't used one in ages - I tossed it long ago on my x58 extreme board and never installed it on the ud7.
Major nusense - always getting in the way.
I run an open case.
When i need extra cooling on the NB I point a fan at it and turn up the rpm's.
I do need to do this when benching with ich10 arrays.

Yeah apparently my chipset block isn't getting good contact, I will get it sorted in a couple days. It was the first waterblock I ever installed and I probably just didn't get it seated properly (though it looks alright) some have said their ek block has had problems making contact so it may not just be my installation. Nb gets 80c+ when I play bc2. Wayyyyy too hot for having active cooling. Will fix it soon.

Yep, agree - it should not be getting that hot under water - no where close to that.

:mad:

First the good news -my 980X arrived today batch 3003B178 stock v core1.184. Is this a good batch - anybody else on here have this batch?

The bad news is that in the last two days my machine has gone bad, and I suspect it is the mobo. Getting lots of BSOD stop 124 and machine check errors. Have checked ram - passed 8 runs of memtest over 5.5hours. Have tried one stick etc etc. Re installed windows on a new hard drive still errors.

weird thing is that Windows will install perfectly fine - usually if there is a hardware problem windows will usually fall over during install. The other very strange behaviour is that I cannot use sleep mode like i used too - it goes into sleep mode but then almost imediately comes out - but with either CF flashing on the boards led or it will just loop at C1 and click like mad, reset button will not work and I have to use the power button to turn off, and then it will sometimes turn back on by itself, or if I restart using the power button it will resume instead of the expected fresh boot ???

Having tested most of it I am feeling it is either the graphics card or the mobo - any ideas from you wizards out there???

Very frustrated as I will noe probably have to send the board back to Giga and wait ages for a replacement - what do you think????

Mark

Well you say you're down to 2 components, one is easily checkable, find a spare graphics card to try. It may even be worth buying the cheapest card you can find just to have a spare in the future.

Quote:

---

Originally Posted by tipes

:mad:

First the good news -my 980X arrived today batch 3003B178 stock v core1.184. Is this a good batch - anybody else on here have this batch?k

---

Have the same Batch! IMHO it's a very good one!

Quote:

---

Originally Posted by crashmax

Have the same Batch! IMHO it's a very good one!

---

Hi Crashmax,

Thanks for the good news - I am sure you are right and that this is a good batch. Might have to wait a while to really find out though grrrr. One thing is a bit strange though one of the cores is about 10 degrees below the others - still nothing to worry about i suppose.

mbresli:

I actually have two other graphics cards in systems I have loaned out to help others- always the way isn't it. I could borrow one back for a day or so I suppose.

Mark

Hi Mark,

Yeah temps are all different. They are inside a range of 10 degrees for me too. So, as you wrote, don't worry about that.

Quote:

---

Originally Posted by crashmax

Hi Mark,

Yeah temps are all different. They are inside a range of 10 degrees for me too. So, as you wrote, don't worry about that.

---

Thanks for the confirmation.

Quote:

---

Originally Posted by stasio

GA-X58A-UD7 - F7e

- 15.Apr 10

---

This BIOS adds the new microcode patch for 32nm, right?

Quote:

---

Originally Posted by SteveRo

Lsdme - what I wrong with @bios for flashing - I have used it many times on multiple ggbt boards - no problem.

---

Please stop using now while you are ahead :yepp: You have been warned :eek:

Quote:

---

Originally Posted by Sam_oslo

This BIOS adds the new microcode patch for 32nm, right?

---

Yeap :up:

Quote:

---

Originally Posted by tipes

:mad:

Very frustrated as I will noe probably have to send the board back to Giga and wait ages for a replacement - what do you think????

Mark

---

Probably is the mbd but just to be sure try another PSU (I know Silverstone are the best but.......) and check all connections and wiring to the mbd.
Maybe graphics is a problem but would the screen not just stay blank if it was a graphics problem?

Quote:

---

Originally Posted by Sam_oslo

This BIOS adds the new microcode patch for 32nm, right?

---

Does that mean I do not have to apply the "Mod"?

Quote:

---

Originally Posted by newhit

Does that mean I do not have to apply the "Mod"?

---

This has nothing to do with any mod's

Quote:

---

Originally Posted by newhit

Probably is the mbd but just to be sure try another PSU (I know Silverstone are the best but.......) and check all connections and wiring to the mbd.
Maybe graphics is a problem but would the screen not just stay blank if it was a graphics problem?

---

Hi newhit,

Strangely enough this all seemed to start after I tried changing the psu to a corsair 750 - had a hell of a struggle getting the 8 pin power to reach the top corner via behind mobo tray - maybe I gave the board a dose of static during this??? Have had a few black screens as well. Have now gone back to my trusty silverstone 850w, only reason I changed to the corsair was because I thought the silverstone was getting a bit too warm in operation.

This morning 2gb of my main memory has dissapeared - yet I fully tested it for nearly six hours the other day with memtest - all ok.

Oh well the diagnosing continues......

Mark

Quote:

---

Originally Posted by Lsdmeasap

This has nothing to do with any mod's

---

Sorry, put 2 and 2 together and got 5. I mistakenly thought this made the resistor mod redundant. Obviously not.

Quote:

---

Originally Posted by tipes

Hi newhit,

Strangely enough this all seemed to start after I tried changing the psu to a corsair 750 - had a hell of a struggle getting the 8 pin power to reach the top corner via behind mobo tray - maybe I gave the board a dose of static during this??? Have had a few black screens as well. Have now gone back to my trusty silverstone 850w, only reason I changed to the corsair was because I thought the silverstone was getting a bit too warm in operation.

This morning 2gb of my main memory has dissapeared - yet I fully tested it for nearly six hours the other day with memtest - all ok.

Oh well the diagnosing continues......

Mark

---

your doing all the right things - switch out components to isolate which one is the problem. think back to what all you have changed since the problem appeared - or is this a new build?

Quote:

---

Originally Posted by tipes

Hi newhit,

Strangely enough this all seemed to start after I tried changing the psu to a corsair 750 - had a hell of a struggle getting the 8 pin power to reach the top corner via behind mobo tray - maybe I gave the board a dose of static during this??? Have had a few black screens as well. Have now gone back to my trusty silverstone 850w, only reason I changed to the corsair was because I thought the silverstone was getting a bit too warm in operation.

This morning 2gb of my main memory has dissapeared - yet I fully tested it for nearly six hours the other day with memtest - all ok.

Oh well the diagnosing continues......

Mark

---

reseat the cpu

Quote:

---

Originally Posted by Lsdmeasap

Nice to see you got it installed, I'll have to check out the latest version then. Installed is easy, does it freeze when you change something/anything and hit apply? That has been my issue with the past 10 or so versions of it

---

Yo LSD,
is does freeze all the time when I try to apply something. I will use the
EasyTuneFreezer6

only for reading the voltages in future. Anything else seams to be senseless:mad:

Lol!! Totally useless program that Easyfreeze 6