i would suggest looking at some of fatguy1999's posts.
http://www.xtremesystems.org/forums/...25#post3856625
he's done some amazing things with a Q6600 and phase and the UD3R
i would suggest looking at some of fatguy1999's posts.
http://www.xtremesystems.org/forums/...25#post3856625
he's done some amazing things with a Q6600 and phase and the UD3R
thanks so much!
Got the UD3R board, I am pretty new with it, but I have reached Q9550 @ 4300 Mhz that is Intel Burn Test ok. My question is what are safe voltages for 45nm Quads with these P45 boards? Do they overvolt or do other bad things with voltages? I have not checked with dimm anything jet.
So what is max for vCore, FSB voltage, also reference voltage, PLL, MCH. I have Q9550 with watercooling, under heavy load Intel burn test 66/66/65/65 max temps.
Can not compare this board with P35 Asus P5K-E, this one loves 500+ FSB with Quad :up: :clap:
With LLC enabled, voltage with a dmm is pretty close to what is set in bios for cpu. Cpu=z tends to read a little lower than the DMM usually.
For ddr I seem to get 2.1 when I set it at 2.06. So it is overvolted a bit.
And safe voltages.... I say 1.4v is as high as I am okay with volting the cpu under regular use. A few runs of spi or 3dm06 should be fine higher.
remember,these boards keep the cpu voltage the same under idle and load, so don't overdo it.
Congrats mate thats an awesome speed of RAM , you scared of 1,5 lol...see what i posted to ya on the Q9650 1,66+ lolQuote:
Originally Posted by Oztopher
Cheers
Sergio
For me it is hard to get 518 FSB OK with Q9550, I did it, but with high FSB voltage, if I remember correctly, it was set to 1.48v in BIOS. What is this safe? I have read, that 1.51 killed a QX CPU, but it was different board :down:
Also I tried FSB reference up to 1.04v with no luck, that was when I reduced FSB voltage to 1.46v, I am aiming for 518 x 8.5, that gives me 4400 Mhz for 24/7, have not tested with 8.5 jet, just 8x, was OK with 4300 Mhz, for tests I use 25 loops of Intel Burn Test. I have also tested skew and it did bad if more than 0 is added for CPU, also 700mv for CPU is the best, 800 is also ok, but 900 or 1000mv is freezing.
Also, this is the same chip Q9550 L845B with 1.275v VID (looked badly first), that was on Asus P5K-E P35, no more than 450 FSB, even 455 had freezing problems, and Gigabyte UD3R board is great. Lets hope in can handle 8 Gb of DDR2 good too, P5K-E did it great, 8gigs at ~ 1100 5-5-5-15. :p:
Does any body here own GTA IV? If so do you get a stuttering with the game? I know it seems off subject but trust me it's not.
If i want to run SATA ports in AHCI mode i must enable both "Sata RAID/AHCI Mode" => AHCI Mode and "Onboard SATA/IDE Ctrl Mode" or just "Onboard SATA/IDE Ctrl Mode" => AHCI mode ? 2 HDD's, no RAID function.
I usually just select both but it seems to really only require the first one being set to ahci.
Is sleep function fixed in bios 10 beta series for ep45-ud3p ver 1.0?
Thank you sergio ! It wasn't anywhere near stable though, just a screeny.
i.e. your post in the q9650 thread, thanks for that as well :) ... i won't be scared to put 1.5v+ for MCH and VTT, as long as it is for short term benching...
I believe the first one is for hard drives only, ACHI is faster than the default. But be warned, for XP you will need to install the ACHI drivers during install...Quote:
Originally Posted by LifeDrainer
The second i believe is for optical drives, correct me if i'm wrong? If i set it to ACHI it loads discs faster etc...
----
I have a bit of a problem that i need some help with.
Basically, i can boot 500x8 and run blend for a while (with 1.28vtt, 1.30mch), not tested for thorough stabilty yet, but it runs for a good half an hour or so before i stopped. But, i went back down and tried to make my way up from 485x8, and it seems i can't get it to even run more than 3 tests of blend :confused: I tried setting the exact same settings as 500x8 and it still doesn't pass 3 tests, i try more voltage and it makes it worse, i tried less and no difference. I messed with the amps, and skews and still can't pass more than 3 tests... :shrug:
I then gave up and tried going for 495x8.5 for a 24/7 clock (4.2ghz... 4.2 is 99% stable at 467x9 at the given vcore), but yet again, it doesn't pass more than 3 tests. I tried 500x8.5 with the same settings and it went on for 20mins :confused: but i blue screened, it doesn't make sense.
I can get 480x8 stable and 500x8 sort of stable, but 485 to 495fsb seems impossible to get stable...
Any thoughts?
wellcome mate, you have to keep testing :up:Quote:
Originally Posted by Oztopher
the Onboard SATA/IDE Ctrl Mode one is for the two purple
sata ports if i remember correctly.the other is the ICH10
intel ports.
I am really having issues going over 450 FSB with E0 E8600 (Bios 10f)
The build: EP45-UD3P board + 2x2Gb Mushkin DDR2 1100 + E8600
All watercooled, CPU with his own loop.
The settings:
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [8X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 3.60GHz( 450x8)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [500]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: 400
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).................: 900
DRAM Timing Selectable (SPD)..........: [Manual]
>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 5]
x tRP.............................5...: [ 5]
x tRAS...........................18...: [15]
>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [4]
x tWTR............................3...: [4]
x tWR.............................6...: [6]
x tRFC...........................52...: [58]
x tRTP............................3...: [4]
x Command Rate (CMD) .............0...: [ 2]
>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [9] or [10]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [9] or [10]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
****** Motherboard Voltage Control ******
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.45V] real [1.408]
CPU Termination........1.200V.........: [1.300V]
CPU PLL................1.500V.........: [1.59V]
CPU Reference..........0.760V.........: [.745]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.40V]
MCH Reference..........0.760V.........: [.72]
MCH/DRAM Reference.....0.900V.........: [1.05]
ICH I/O................1.500V.........: [1.5V]
ICH Core...............1.100V.........: [1.1V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V] memory is rated 1100 at 1.9V
DRAM Termination.......0.900V.........: [1.05]
Channel A Reference....0.900V.........: [1.05]
Channel B Reference....0.900V.........: [1.05]
Anything over that 455 x 8 is a no post. But as it is now is LINX 20 pass stable. CPU voltage can be much lower @ these settings will go with VID. Which is 1.250.
Memory is well capable of 1200 at 2.2V.
CPU can go 4.5 Ghz on MFII.
I tried all sorts of trial and error tests, read the forum etc. but i am stuck!
So what do you think? Could someone who knows his way with 2-cores give me some input? Thank you!
Read this thread,maybe will help you:
http://forums.tweaktown.com/f69/ga-e...-450fsb-31949/
Quote:
Originally Posted by radaja
very NICE chip :up:, with v1.35, my e84 only can touch 4.45 GH :down:
http://i34.tinypic.com/1gc4m.jpg
FOR FSB 525 ( 4.75 GH ) can do with v1.36, BUT only 4 Super PI 1 MB.......:D :up:
http://i34.tinypic.com/jgmz6e.jpg
VNB 1.38v, DDR2 1200 5/5/5/15 @ 1.9v
FSB 1200 cl 5/5/5/15 @ 1.90v
http://i33.tinypic.com/33ngcig.jpg
Gaul,thanks.looks like youve got a nice one too.
which board is that on?the UD3P?
Thanks for posting this. I copied and got to the same 4GHz easily. I lowered the vCore a little (1.39) and left the thermal monitors and C1 stuff enabled.Quote:
Originally Posted by Phunky Phish
Unless someone has something better I'll stick with this config. Thanks again!
Here is mine.
http://img32.imageshack.us/img32/1180/wootp.png
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ..................: Auto
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio......................: +0.5
CPU Frequency ............................: 4.00Ghz (500x8.5)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control....................: [Enabled]
CPU Host Frequency (Mhz) .................: 500
PCI Express Frequency (Mhz) ..............: 101
C.I.A. 2..................................: [Disabled]
Advanced Clock Control
CPU Clock Drive...........................: 1000mV
PCI Express Clock Drive...................: 1000mV
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps
DRAM Performance Control
Performance Enhance......................: Turbo
MCH Frequency Latch......................: 333
System Memory Multiplier ................: 2.40D
Memory Frequency (Mhz) ..................: 1200
DRAM Timing Selectable ..................: Manual
Standard Timing Control
CAS Latency Time.........................: 5
tRCD ....................................: 5
tRP......................................: 5
tRAS.....................................: 18
Advanced Timing Control [Press Enter]
tRRD.....................................: Auto
tWTR.....................................: Auto
tWR......................................: Auto
tRFC.....................................: Auto
tRTP.....................................: Auto
Command Rate (CMD) ......................: 2T
Channel A
Channel A Timings Settings
Static tRead Value......................: 8
Channel B
Channel B Timings Settings
Static tRead Value......................: 8
Motherboard Voltage Control
Load-Line Calibration.....................: Enabled
CPU Vcore...............1.22500V..........: 1.3875~ under load 1.344
CPU Termination.........1.200V............: 1.44
CPU PLL.................1.500V............: 1.570v
CPU Reference...........0.760V............: 0.937
MCH/ICH
MCH Core................1.100V............: 1.50v
MCH Reference...........0.760V............: 0.912v
MCH/DRAM Reference......0.900V............: 0.96v
ICH I/O.................1.500V............: 1.500v
ICH Core................1.100V............: 1.200v
DRAM
DRAM Voltage............1.800V............: 2.0v
DRAM Termination........0.900V............: 0.86v
Channel A Address Vref..0.900V............: 0.86v
Channel B Address Vref..0.900V............: 0.86v
Advanced Settings
Limit CPUID Max. to 3.....................: Disabled
No-Execute Memory Protect.................: Disabled
CPU Enhanced Halt (C1E)...................: Disabled
C2/C2E State Support......................: Disabled
x C4/C4E State Support....................: Disabled
CPU Thermal Monitor 2(TM2) ...............: Disabled
CPU EIST Function.........................: Disabled
Virtualization Technology.................: Disabled
Those figures look ok but I would suggest dropping PL to 9 or 10 and PLL to 1.50 since these boards overvolt pll.Quote:
Originally Posted by pezcore
Ok I changed PLL to 1.5v
What's PL?
I'm also curious to know why CPU-Z reports Core Voltage at an almost constant 1.424v when I had it set to 1.39 (and just lowered it to 1.38, still no change)
Anything else I could lower?
Here are my settings on my board with a q6600 and a single stage, anything i should change or anything too high on volts? this is just my first play with overclocking on this board, hopefully i can get to 4.4 or 4.5ghz. What should i set me memory to? These new settings on this board confuse me a little.
The settings:
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.05GHz( 450x9)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [450]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: 333
System Memory Multiplier (SPD)........: [2.00C]
Memory Frequency(Mhz).................: 1080
DRAM Timing Selectable (SPD)..........: [Auto]
****** Motherboard Voltage Control ******
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.5]
CPU Termination........1.200V.........: [1.38]
CPU PLL................1.500V.........: [1.61]
CPU Reference..........0.760V.........: [.914]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.34]
MCH Reference..........0.760V.........: [.914]
MCH/DRAM Reference.....0.900V.........: default
ICH I/O................1.500V.........: [1.570V]
ICH Core...............1.100V.........: [1.200V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.18V]
Everything else auto or default
nvm
PL on this board is Static tRead. Im not sure why your reported vcore would be higher than the bios setting, should be several steps lower than bios/et6.Quote:
Originally Posted by pezcore
I use an EK 5 for the northbridge.Quote:
Originally Posted by Allubz
thanx....up sory e84 with ASUS P5Q, just 4 compare u'r mighty chip...Quote:
Originally Posted by radaja
but the ddr 1200 use UD3R
I found out the reason why anything inbetween 480fsb and 500fsb wasn't stable... it was RAM. Strange...
It seems so picky with what timings can be set. At 467fsb with ram at 1868mhz 8-8-8-22, trfc 59, it ran blend overnight (8hours or so), using custom 3200mb of memory. But at 485fsb with 1940mhz on ram, the timings needed to be set to 10-10-10-28, trfc 84, to at least run blend for 10mins (i didn't test further). Yet 500fsb with ram at 2000mhz, with 8-8-8-24, trfc 84, it ran for an hour.... the ONLY thing different was that cmd rate was at 1n, which i can't set myself, it never sticks when i set in bios, only at 500+ it auto sets to 1n.
Is there something i'm missing with DDR3? I'm not too familier with RAM overclocking, i always thought it was pretty straight forward :shrug: Can anyone share their experiences and tips with DDR3? i would really appreciate it :)
Oz
Oztopher I am struggling on my ddr3 board as well, what are your complete settings including GTL refs?
Hey guys so I have a gigabyte e45-ud3p and an intel q6600 quad SLACR. I need some help with overclocking on the unit. I am on Phase change for the CPU cooling wise. With 2 spot cools over the NB and the RAM. I have a bench table, so everything is open air cooling also.
My Questions:
What are the safe voltage areas for my particular setup? Am I safe where I am at now? Can i go higher in some areas?(See Log of Settings)
What are some settings I can try for my memory. I dont quite understand the ratios anymore and Im not sure if the few attempts ive had BSOD because ive set memory to high or something. I have GSKILL F2-8500CL5D-4GBPI PC2-8500 5-5-5-15 2.1.
Is there anything you can see in my settings that I should change?
Quote:
The settings:
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.05GHz( 450x9)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [450]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: 333
System Memory Multiplier (SPD)........: [2.00C]
Memory Frequency(Mhz).................: 1080
DRAM Timing Selectable (SPD)..........: [Auto]
****** Motherboard Voltage Control ******
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.5]
CPU Termination........1.200V.........: [1.38]
CPU PLL................1.500V.........: [1.61]
CPU Reference..........0.760V.........: [.914]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.4]
MCH Reference..........0.760V.........: [.914]
MCH/DRAM Reference.....0.900V.........: default
ICH I/O................1.500V.........: [1.570V]
ICH Core...............1.100V.........: [1.200V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.18V]
Everything else auto or default
Hey mate, these are my settings so far for 467x9: (8hours or so stable on prime blend) Obviously some things will be different depending on how good ur chip, board and ram are.Quote:
Originally Posted by gurusan
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...................: Auto
CPU Clock Ratio ...........................: 9x
Fine CPU Clock Ratio.......................: --
CPU Frequency .............................: 4203Mhz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.....................: [Enabled]
CPU Host Frequency (Mhz) ..................: 467Mhz
PCI Express Frequency (Mhz) ...............: 101
C.I.A. 2...................................: Disabled
Advanced Clock Control
CPU Clock Drive............................: 800mv
PCI Express Clock Drive....................: 900mv
CPU Clock Skew (ps)........................: 0ps
MCH Clock Skew (ps)........................: 0ps
DRAM Performance Control
Performance Enhance........................: [Turbo]
(G)MCH Frequency Latch.....................: [333]
System Memory Multiplier ..................: 4.00B
Memory Frequency (Mhz) ....................: 1868Mhz
DRAM Timing Selectable ....................: [Manual]
Standard Timing Control
CAS Latency Time...........................: 8
tRCD ......................................: 8
tRP........................................: 8
tRAS.......................................: 22
Advanced Timing Control [Press Enter]
tRRD.......................................: 4
tWTR.......................................: 4
tWR........................................: 8
tRFC.......................................: 59
tRTP.......................................: 4
Command Rate (CMD) ........................: Auto
Channel A Timings Settings [Press Enter]
Static tRead Value.........................:7
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:Auto
Twr2wr(Different Rank).....................:Auto
Twr2rd(Different Rank).....................:Auto
Trd2wr(Same/Diff Rank).....................:Auto
Dimm1 Clock Skew Control...................:+200 ps
Dimm2 Clock Skew Control...................:Auto ps
DDR Write Training ........................: Disabled
DDR Write Leveling ........................: Disabled
Channel A Driving Settings [Press Enter]
Driving Strength Profile...................:Auto
Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto
Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto
Channel B Timings Settings [Press Enter]
Static tRead Value.........................:7
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:Auto
Twr2wr(Different Rank).....................:Auto
Twr2rd(Different Rank).....................:Auto
Trd2wr(Same/Diff Rank).....................:Auto
Dimm1 Clock Skew Control...................:+200 ps
Dimm2 Clock Skew Control...................:Auto ps
DDR Write Training ........................: Disabled
DDR Write Leveling ........................: Disabled
Channel B Driving Settings [Press Enter]
Driving Strength Profile...................:Auto
Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto
Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto
Motherboard Voltage Control
Voltage Type.………... Normal
CPU
Load Line Calibration......................: [Enabled]
CPU Vcore....................1.225v........: v 1.38750
CPU Termination….............1.200V*.......: v 1.24
CPU PLL......................1.500V*.......: v 1.50
CPU Reference................0.760V*.......: v 0.785
MCH/ICH
MCH Core.....................1.100V........: v 1.24
MCH Reference................0.800V........: v 0.785
MCH/DRAM Ref.................0.750V........: v 0.940
ICH I/O......................1.50V.........: v 1.50
DRAM
DRAM Voltage.................1.500V........: v 1.90
DRAM Termination.............0.750V........: v 0.940
Channel A Data Reference.....0.750v........: v 0.940
Channel B Data Reference.....0.750v........: v 0.940
Channel A Address Reference..0.750v........: v 0.940
Channel B Address Reference..0.750v........: v 0.940
Advanced Settings
HDD S.M.A.R.T. Capability..................: [Disabled]
CPU Multi-Threading........................: [Enabled]
Limit CPUID Max. to 3......................: [Disabled]
No-Execute Memory Protect..................: [Disabled]
CPU Enhanced Halt (C1E)....................: [Disabled]
CPU Thermal Monitor 2(TM2) ................: [Disabled]
CPU EIST Function..........................: [Disabled]
Virtualization Technology..................: [Disabled]
Can someone give me some info please, I want to know if its possible to run this memory cooler with the UD3P mobo without any clearance issues with the heatsinks
http://www.newegg.com/Product/Produc...82E16835116021
The only issue you might run into is with whatever CPU cooler you are using. I have the Corsair Dominator fan on my ram and the only thing is that is sits high in front of the CPU fan. I don't think it would effect performance either, but maybe accoustics.Quote:
Originally Posted by Regalia87
My computer has been unhappy lately. When I enable LLC, the voltage stays above 1.4v almost always. When I disable, it drops as low as 1.392.Quote:
Originally Posted by Hoss331
The problem is that I'm getting higher temps with the higher voltage (46*C or more idle) instead of 40. I keep reading about people having vCores in the low 1.300's, how can I do that? (or is that what happens when you get a "good chip"?)
I'm also getting blue screens here and there and games have frozen on me a few times (I was playing Batman AA and it froze) I'm having a hard time figuring out if this is the GFX card's problem though...
Any suggestions on where to start?
Is PLL set to 1.5 keeping my vCore higher than what I set it to with LLC enabled?
I had 500 FSB 1:1 stable with MCH 1.26 V, 2x2 GB. Haven't tried lower voltages. That was on Core2Duo though.Quote:
Originally Posted by Hardc0r3
Got that issue 2, on 333 strap 2.00b with pl9 when restarting after a 12 h succesfull run of prime95 and when it finally gets going my setup is on default clock, and can't boot anymore with pl9. When i put pl 10 i have no issues on booting.Quote:
Originally Posted by LifeDrainer
Hi Guys
I need you to help me .
I Have EP45-UD3R Rev 2.1 // Q9550 E0
I want to know what is the best bois should i use with my Ep45 , Im using the F11 .. Also i want to know if it safe to downgrade the bois or not ??
because i noticed a bug in the F11 bois
When i choose some volt configration ( speially the CPU Ref Volt , MCH Reference Volt) some value in bois then open ET6 in Windows i Relaize that the Volts had been changed wo be less that i chose
for example when i choose CPU Ref Volt 0.85 i open ET 6 then find it 0.76 !! so wut is the real one ?
but when i set these volt to be .85 in ET6 i got more stabilty in overclocking
So is this normal ???
Thanks guy , waitng for you help
thats not a bug thats the way it works.here read this.
http://www.xtremesystems.org/forums/...postcount=1157
the line in red is what ET6 will report.Code:
ET6...../0.730 / 0.745 / 0.760 \ 0.785 \ 0.800
vtt 1.20 0.730 / 0.745 / 0.760 \ 0.785 \ 0.800
vtt 1.22 0.742 / 0.757 / 0.772 \ 0.797 \ 0.812
vtt 1.24 0.755 / 0.770 / 0.785 \ 0.810 \ 0.825 CPU reference value in bios
vtt 1.26 0.768 / 0.783 / 0.798 \ 0.823 \ 0.838
vtt 1.28 0.780 / 0.795 / 0.810 \ 0.838 \ 0.850
vtt 1.30 0.793 / 0.808 / 0.823 \ 0.848 \ 0.863
vtt 1.32 0.806 / 0.821 / 0.836 \ 0.861 \ 0.876
vtt 1.34 0.818 / 0.833 / 0.848 \ 0.873 \ 0.888
vtt 1.36 0.831 / 0.846 / 0.861 \ 0.886 \ 0.901
vtt 1.38 0.844 / 0.859 / 0.874 \ 0.899 \ 0.914
vtt 1.40 0.856 / 0.871 / 0.886 \ 0.911 \ 0.926
vtt 1.42 0.869 / 0.884 / 0.899 \ 0.924 \ 0.939
vtt 1.44 0.882 / 0.897 / 0.912 \ 0.937 \ 0.952
vtt 1.20 0.720 / 0.740 / 0.760 \ 0.800 \ 0.840
vtt 1.22 0.732 / 0.752 / 0.772 \ 0.812 \ 0.852
vtt 1.24 0.745 / 0.765 / 0.785 \ 0.825 \ 0.865 MCH reference value in bios
vtt 1.26 0.758 / 0.778 / 0.798 \ 0.838 \ 0.878
vtt 1.28 0.770 / 0.790 / 0.810 \ 0.850 \ 0.890
vtt 1.30 0.783 / 0.803 / 0.823 \ 0.863 \ 0.903
vtt 1.32 0.796 / 0.816 / 0.836 \ 0.876 \ 0.916
vtt 1.34 0.808 / 0.828 / 0.848 \ 0.888 \ 0.928
vtt 1.36 0.821 / 0.841 / 0.861 \ 0.901 \ 0.941
vtt 1.38 0.834 / 0.854 / 0.874 \ 0.914 \ 0.954
vtt 1.40 0.846 / 0.866 / 0.886 \ 0.926 \ 0.966
vtt 1.42 0.859 / 0.879 / 0.899 \ 0.939 \ 0.979
vtt 1.44 0.872 / 0.892 / 0.912 \ 0.952 \ 0.992
BTW radaja, congrats on that q9650. You got a great chip there, you waited a long time for one.
thanks.problem is since i dont have time to really
OC right now im just going to sell it.:(take a couple of months
off,its a shame too cause your right it did take me awhile
to find it.
Does this motherboard have the right sound connections for an X-5500 speaker system? What kind of speakers can it support?
I bought me a UD3P as a backup board sense they so low in price now from Newegg with (Free Shipping).I gotta say. I kinda like so far so good on the Oc'ing right now
http://img402.imageshack.us/img402/2...4250ghz.th.jpg
http://img134.imageshack.us/img134/8629/everestg.th.jpg
http://img524.imageshack.us/img524/3...tsensor.th.jpg
Some new BIOS's released.:D
http://forums.tweaktown.com/f69/giga...st-bios-28441/
F10I, Yay for having quick boot :up:, boo for still having lower reads and higher latency. :down:
What do you guys think about the EP45T-UD3LR? will the 4 pin ATX and 4 phases hold back the same stable OC I got on the EP45-UD3R?
rev. 1.0 and rev 1.1 work fine with the same BIOS, aren't they?Quote:
Originally Posted by Hoss331
I read the new P45 bioses unlock 0.5 multi, someone with Q9450 8x333 can use the 0.5 multi, so he get 8.5x333. can someone confirm that?
damn again ? pff i will stick on F10b then...Quote:
Originally Posted by Hoss331
Quote:
Originally Posted by Hoss331
Lower reads and higher latency? What exactly are you talking about? I have been scratching my head for the last couple days as to why my SSD has slower reads than it should and latency a littler higher than it should. Is this what you are referring to?
again.....UD3R.......
HIGH VID i got.........:(
http://i50.tinypic.com/2rh5kkh.jpg
From F10e bios and on, everest tests and others reads lower bandw. and higher latency on mem...Quote:
Originally Posted by ProStreetCamaro
Still F10b is the best inmo.
Cheers :up:
Sergio
yes mate, but stick to F10b bios if you can, inmo the bestQuote:
Originally Posted by ACK
too late!!:(Quote:
Originally Posted by andressergio
I've udated to F10i and pcie link width drop to 2x
http://s4.subirimagenes.com/otros/3625324linkwdth2x.jpg
I'm scared :shocked:
After that i replace cpu-z to the last version (see pic)
and update nvidia drivers to the last version too, but no success
Can I come back to f10b?
I had previous f9
dont worry mate...Quote:
Originally Posted by ACK
if it don't let you do it on Qflash just use FLASHSPI on DOS with a bootable pen drive and go back to F10b
Cheers
Sergio
nice, just flashed to f10i everything good still no problems, quick boot thing is nice
you will not have problems for sure but did you test your scores before and after ?Quote:
Originally Posted by redrumy3
btw what is quick boot thing ?
cheers
Sergio
andressergio is 10b best for the gigabut?
yes mate nice and fast bios :up:Quote:
Originally Posted by zsamz_
Mine still shows x16 link width but oddly doesnt show anything else. :shrug: Quick boot feature allows you to boot quicker, :) about 4-5 seconds faster when enabled on mine.
http://i131.photobucket.com/albums/p...281/biisdg.jpg
reboot time
http://i131.photobucket.com/albums/p...ss281/boot.jpg
I think this BIOS F10b still have problem in Windows 32-bit, reading memory(2x2GB) 3.25 GB instead of 3.5 GB,old AHCI ROM 1.07.Quote:
Originally Posted by andressergio
Yes hoss same here, cpuz shows the same
my reboot time is longer as im on raid 0 2x500 seagates 7200.11 and dual boot slows a bit but i get 9 seconds less :D
http://img4.imageshack.us/img4/3382/biosf10i.jpg
Cheeeeez :up:
Sergio
stasio, didnt know but on 64 bits works as a charm, tough im testing this new one and confirm that mem scores higher latency and bandw but well...Quote:
Originally Posted by stasio
Ran bios 10i here but all it does is basically "hide" the dos dmi pooling screen, its not really quicker.
you can't see bios/mb info on mainboard tab in cpuz
ram latencies here were about 82.5
Went back to 10f and all good, can see bios info in mainboard tab now on cpuz and ram latencies are 64.4
BUT I can't run Gpuz it crashes error.
i did get newest nvidia drivers so that may be Gpuz issue with them.
no problems here mate with GPUZ neither with new 195.62 drivers bios just fine and yes its faster...10 - 9 seconds on my system less to boot, yes latencies are a bit more but its not new cauz since F10e they've been doing this, i could get more OC on 8,5 multi as maybe they modified timmings on chipset..Quote:
Originally Posted by tyreman
Cheers :up:
Sergio
Andressergio...You using to 10b?
i was now testing F10i seems nice all my OC works as a charm, faster to boot, just using the PC as always no problems at all.Quote:
Originally Posted by tyreman
Why you ask ?
Cheeezzz!!
Sergio
I think at one time you using 10b.
+1 :up:, ran a quick prime test last night with F10I and so far so good. No real surprises other than no MB info in cpuz and maybe a glitch in memset since it now displays ram size just as 2048 instead of 2x2048.Quote:
Originally Posted by andressergio
http://i131.photobucket.com/albums/p...ss281/4625.jpg
I'm eyeing-up a v1.6 board at the moment, I could go for a 1.1 too, are either better than the other?
jojo !!! kick ass run Hoss congrats :up:Quote:
Originally Posted by Hoss331
yes mate i was using in till yesterday but think i will stay on this bios, seems nice, hope giga keeps improving this great board :up:Quote:
Originally Posted by tyreman
Anyone have a spare i/o shield for the EP45-UD3R or UD3P they would let me have or sell me for $5/shipped? Please PM me. I need one ASAP.
Soo hows the s775 life been treatin u all? Andre, Hoss, 007, radaja, etc? I miss u guys, yall need to step on up!! Just for comparison, i haven't tried anything under 4200mhz with the i7, but at 4200, i'm crushing all my benchies with the ud3p and q9650 @ 4.5 8GBgskill1200. I hesitated for a while before i jumped in, but i can say its 100% worth it. SLI and Xfire with the same board? Thats good stuff! SLI without nForce..Thats good stuff! I picked up one of these, new in box, from a junkie for cheap ($600) and played around with it. I changed the power supply and added a TRUE and was at 4200 Stable in 30 minutes with the factory 9gb of ddr3 running it at 1600. This bargain ASUS was killing my water cooled q9650. I sold the 9650 rig and went all out on a new i7 rig (in my sig) and i'm loving it. My new Gigabyte ex58a UD7 will be here Tuesday so maybe i'll run in to some of yall in the Gigabyte EX58 thread. If your not in there, i recommend coming as soon as you can! Sell that s775 Monster while you still can and step it up! lol STEP it UP!! :rofl: Andre your single 285 is getting lonely. Wouldn't it be nice to add 1, 2 or even 3 more 285's to your machine? You can do it if you step up!! lol :ROTF::yepp::ROTF:
He can run SLI just fine on the UD3P ;)
It isn't so much about the scores on the 775/DDR2/Quad stuff...it is all about the fun and tweaking ;)
How can he run SLI? MultiGPU cards dont count :p: The "fun and tweaking" applies to the i7's as well :yepp:....plus they're much faster!! but who cares about speed right? :DQuote:
Originally Posted by tool_462
Check post #4991 for SLI :up:
WOW Thanks......i guess he CAN do SLI. Has anybody else tried it? does it scale like a true SLI system? Thats awesome.. Gotta read up on that one.Quote:
Originally Posted by Hoss331
Not sure who else has tried it, but it sure looks to scale pretty well to me. :up:
Thank u very much, I go back to F10b as you said and problem solved. F10b is a great BIOS.Quote:
Originally Posted by andressergio
I am still trying to figure out why I can't run dual channel mode. I am on my 4th mobo and had upgraded my PSU. I think I need to pull everything out of the case and see what happens then.
Gigabyte needs to give you a life time free motherboard supply, I remember at the beginning of the year seeing you post about only being able to run single ch mem. If you are still running single ch on a giga board you are truly a loyal customer, someone from gigabyte needs to read this thread and see the issues you have had and make it right. I would have abandoned gigabyte long ago and joined zsamz in the "I hate gigabut" club. Honestly I would be extremely pissed off and never purchase another product from them.Quote:
Originally Posted by clo007
its nothin new either the board works great or it has memory slot problemsQuote:
Originally Posted by OC Nub
piss poor quality control
but not bein able to run duallchannel is totally unacceptable
clo007 are they sending you the same board back ??
I like the board and its overclockability. I just wish i could get dual channel memory going. Funny thing is, I bought this one from a member here and he said he had no issue running dual channel mode, so I have no freaking clue why it would work for him but not for me.Quote:
Originally Posted by OC Nub
I have not rma'd a board. I just buy new ones form people or I flat out returned to newegg twice now.Quote:
Originally Posted by zsamz_
I am going to pull all my stuff out of my case this weekend and see if I can get dual channel running. I don't know if its a grounding issue, some sort of corrupted file somewhere or what not. The last time I talked to gigabyte about the board they were very unhelpful. I posted the email conversation far back in this thread on what they said.
I like the board but I want it to work to its full capacity. maybe I need to suck it up and go for a different manufacturer, but who? i was thinking Asus but I keep reading bad things about them too now.
TO touch FSB > 500, my UD3R need Vnb = 1.600
http://valid.canardpc.com/show_oc.php?id=856772
For the q9550 it is one of the best boards around. You said maybe some sort of corrupted file, have you tried it on a fresh install? Not an image of an old install but a fresh install.Quote:
Originally Posted by clo007
verry weirdQuote:
Originally Posted by clo007
and as if most are honest if board functionin properly
u should rma 1 straight to gigabut
from the 3 boards i have touched only mine is perfect only issue with others is limited 4x1 clocking
What does install have to do with it? or am i missing something. Install shouldnt have anything to do with your boards not working with dual channel. Wont even POST with dual channel config right?Quote:
Originally Posted by OC Nub
Revised GA-EP45-UD3P -BIOS F10j
released 01.Dec 09
That didnt take long to fix the cpuz issues.
Yeah,just need your respond guys.:up:Quote:
Originally Posted by Hoss331
Well how about fixing S3? :D
+1Quote:
Originally Posted by Hoss331
and what about better latency :D
Thanks Stasio !!!
Cheers
Sergio
anyone ever try F12 for UD3R ???
BIOS F12 for UD3R is not released yet.:rolleyes:Quote:
Originally Posted by Gaul
I want some bios updates for the T series... Go go Raymond !!
I've really hated my EP45C-UD3R....ever since I've moved from my old P5Q Deluxe I've hated pretty much every other board, but none was as bad as the EP45C! It has FSB holes all over the place and only a couple of the dividers work, and it's barely stable at pretty much any overclock.
However, I am still convinced that the Gigabyte series is worth trying so I've got myself an EP45T-UD3P. I certainly hope this works out for me as so far my 775 DDR3 adventures have been less than amazing :/
If this doesn't do it for me then I dunno what I'll do.
DDR2 versions > DDR3 if you read the thread only a couple of people got the DDR3 boards going, and all had a lot of problem to stabilize them.Quote:
Originally Posted by gurusan
i've ever see, but still on BETAQuote:
Originally Posted by stasio
i agree with Jor3lbr,you should have saved your self some trouble and just got the ddr2 variant,its about as solid as its gets.Quote:
Originally Posted by gurusan
clo007,man im so sorry to hear your still dealing with this issue.
Well I see people with the Ep45T extreme doing 500+ fsb clocks and leeghoofd seemed to do well with the UD3P
yea it can be done but the ddr2 board is the way to go.
ddr3 and p45's arent the best match.