i traded for it. its a XFX Alpha Dog Extreme Edition 640m (PV-T88P-YDE4)Quote:
Originally Posted by drizzt5
Printable View
i traded for it. its a XFX Alpha Dog Extreme Edition 640m (PV-T88P-YDE4)Quote:
Originally Posted by drizzt5
i found the ovp mod :p i removed one resistor that was conected to the ovp pin and it had 114k when it was soldered and i replaced it with a 500k Vr and i set it @ 140k now she has ovp from 1.3 to 1.45 Volt i will post photos later today if someone has the same card the strange thing is that the resistor was from the side of the card where the voltera is :/
anyway now i can bench the core @ 870 @ 1.4 volts it's seems a litle crappy but what can i do :p
i need to find caps now :/ anyone know what caps do i need :p ? 1600 μF 6.3V are the ok ?
if anyone needs this
this is the Ovp for the axle 8800gt
remove the second resistor and solder one 500k Vr trim it to ~200k when it is soldered and you will get ovp @ ~1.45 V trim it to a higher resistor and the ovp kick will raise more
http://img99.imageshack.us/img99/1847/dsc02219af5.jpg
and this is the Vcore mod 50 K Vr to Ground
http://img228.imageshack.us/img228/7020/dsc02221yy1.jpg
and these are the measuring points
http://img152.imageshack.us/img152/6024/dsc02216mu3.jpg
and this is the Vmem Mod ( that i haven't test yet so until i will i take no responsibility if anyone burn his card )
http://img225.imageshack.us/img225/1487/dsc02222pl2.jpg
Great job Panos (Vatos_locos) :up: :clap:
You sure went through these data sheets really carefully :D
i just done with the mems mod and it works fine :)
I can confirm this,it's working...Quote:
Originally Posted by _Unstoppable_
@ Quake6 :
What were your final results? I have been waiting patiently for some better info on this alpha dog vmod. Previous posts were a little unclear on were the solder points are for the VR.
has vMEM pencilmod for ECS 8800GT 256mb?
http://www.phoronix.net/image.php?id...8800gt_opp_lrg
anyone?
post o a good pic of the voltera chip ;)
the square one in the middle end of the card
not sure about pencil mod but mem chip is on other side of the card at the rearQuote:
Originally Posted by gugle
http://i90.photobucket.com/albums/k2...8small-1-1.jpg
vmod here
http://i90.photobucket.com/albums/k2...Image049-1.jpg
ecs 8800gt has been cover'd in thread :)
???
the 1st image is vmem chip look @ red dotQuote:
Originally Posted by gugle
and 2nd image is vcore chip
ok, hich clock that comes with its vga 1.4v? (Air)Quote:
Originally Posted by EvoCarlos
my ECS memo is Hynix
Quote:
Originally Posted by gugle
What resistor has to use to make the mod's vgpu and vmem?
vgpu is only call anywhere in red earth?
[] 'S
Hi Guys !
I am looking for pencil or bios vmod for my Palit 8800 GT non refernce cooling. But i can`t take of my cooling system from my card becouse there is a plug.
ok i got my new gt in and i want to voltmod it. were can i find a 500Ω VR?
Quote:
Originally Posted by largon
Can i shade them with a pencil? I think my ocp kicks in at 1.4v over 840gpu and 2000 shaders, and i'm stuck with it. I'm lazy soldering, i'd rather go for a pencil :up:
Is that possible?
Does anyone have or can anyone help with the ocp mod for this xfx 8800gs (same as gt) please ? The ic is labelled BN-9H.Thank you.
http://homepage.ntlworld.com/peter.j.../8800gs-01.JPG
Simply: No, it just doesn't work right. I just soldered a couple cheapy Radio shack resistor in parallel and it worked great.Quote:
Originally Posted by Niccolò
Do you have a high res pic of the whole back of the card?Quote:
Originally Posted by Thickbrit
Hey thanks.This is about as good as my camera gets.If you need macros of specific areas i can do that or i can borrow a camera for better pics of the whole pcb.
http://homepage.ntlworld.com/peter.j.../8800gs-02.JPG
OK you gurus! Anybody knows how to do the OCP on the Galaxy 8800GT? Mine card is already voltmodded (look at post # 832) and I came to a limit on LN2. It looks like 1.5V under load it the end of this card. Need the OCP mod now. :shrug:
HitandRun,
OCP: find a surface mount resistor connected to pin#35, measure resistance across the resistor (basically between pin#35 and ground). Solder a VR rated ~20 times the measured value across the resistor. Lower resistance to push back OCP trigger point.
About OVP (as per PM)....
Does the card crash if you increase voltage without any load on the GPU?
About OCP/OVP looks like I was lucky, 1.55v on load (aircooled) without any trouble