I wouldnt recommend using a pencil mod with this one... 200k means you will probably raise the voltage too far with a pencilQuote:
Originally Posted by Janchu88
Besides pencil mods wear off after a while
Printable View
I wouldnt recommend using a pencil mod with this one... 200k means you will probably raise the voltage too far with a pencilQuote:
Originally Posted by Janchu88
Besides pencil mods wear off after a while
I also tried this,but only for memory is working...Now my memory can do 1160MHz (2320MHz) :)Quote:
Originally Posted by _Unstoppable_
Any ideas for vgpu?
can you tell us the name of the vgpu chip?:)
Bn-9j
31j
Than the vmod should be working, are you sure you used a 5k for te vgpu?(And did you solder it to the resistor (the black smd thing), because the yellow soldering point on the picture is just the ground)Quote:
Originally Posted by quake6
I solder on yellow :hitself:
I'll try for a few day...
i also have this PCB and have been looking for a voltmod. the highest i can get on stock voltages is 740/1850/1095. heres also my highest 3dmak06 score.Quote:
Originally Posted by jason4207
http://img48.imageshack.us/img48/1086/15222sv1.jpg
hi
who did vmod on this card. I can find read points and vmod point (mem and gpu).
twintech 8800gt xt oc mem samsung
http://img229.imageshack.us/img229/951/pict9322oz8.jpg
http://img60.imageshack.us/img60/4642/pict9370sy9.jpg
http://img253.imageshack.us/img253/4342/pict9392dz0.jpg
Anyone know how to mod an Axle 8800Gt non reference pcb ? i made a thread and i am pissed off that i cant mod this card :mad:
here is the thread
http://www.xtremesystems.org/forums/...d.php?t=194364
You got a PM!Quote:
Originally Posted by Vatos_locos
thanks HitandRun :) i appreciate it
here is the VCore mod For the Axle 8800Gt with the zerotherm cooler Confirmed it works with a 50k Vr but she has overvoltage protection @ 1.3Volts :( now i have to find the ovp mod :p
http://img234.imageshack.us/img234/879/dsc02216kv3.jpg
Nice! What clocks are you getting right now?Quote:
Originally Posted by Vatos_locos
At 1.26Vcore (load) she can go up to 780Mhz Artifacts free with ati tool and 800 for benchmarks but i need to solder some cap's on the coils she have some huge spikes between Vantage tests wile she change 2D to 3D voltages and sometimes she goes at 1.3 and the ovp kicks :cool:
i think i found how to override the ovp and set it @ 1.62V but i'am not at home now to test it
for the Vcore measure point i used one of the cap's leg next to the pwm coils and it seems accurate 1.1 with the mod off
http://img230.imageshack.us/img230/2...vgpudn0.th.jpg
i did the 1.1v bios mod to my xfx and now i can go up to its looks like 800/2000 maybe higher, if i had better cooling. im on the stock heat sink for now, im waiting for my MCW-60 & D-Tek Fuzion to show up. but im happy for now @ 780/1950/2100 on the stock heatsink
so i have a very crappy card :S :(
From my good experience, these cards are not worth watercooling. Thermalright HR-03 performed same as MCW-60 even though the latter loaded +10C less. But Going from stock -> MCW-60 should be great :). These cards are limited by 2-phase PWM. Unless you cherry pick your card, don't expect miracles with better cooling. Get a good 120MM and cool the back of the card. @Vatos_locos, forget about the coils, it's worthless and silly. I recommend soldering extra _low esr_ capacitors in parallel to even out the spikes.
i have the card on water because i have build my case this way so the has a dedicated loop and the cpu an other on
will do with the caps :up:
Good luck, I can't wait till you solder them. Report back the results, take a pic of caps too :DQuote:
Originally Posted by Vatos_locos
Thanks Man :) but first i need to do the ovp mod witch i don't know how lol :D
Bios mod eh and you get those clocks? oo, were do u get it? I might wanna try it :)Quote:
Originally Posted by whe3ls
i use the same bios from xfx i can get the core 800Mhz only if i keep the shaders @ stock and the mems @ 1000Mhz but my card had 1.1 V by default :/
i need to check what mine is at. Some guy flashed his bios to 1.2v's btw.
http://www.overclock.net/2966590-post8.html
Although his clocks kind of sux, since your getting 800mhz with lower v's.
i need help too :( i can' find the ovp mod for my 8800gt and i cant go over 800Mhz without it :(
anyone can help ?
i will post a pic of the voltera when i go home but i don't have a good camera if anyone has an Axle 8800Gt if he could take a good picture for me plz :)
anyone ? :( i know the pin for the ovp what should i do :p ?
ovp pin to ground is 104KΩ