the only thing is that it can get to mid 90c as it is i dont want to burn it outQuote:
Originally Posted by hotwaxisbad
ps i dont know what the card can go to with the temp
thanks
the only thing is that it can get to mid 90c as it is i dont want to burn it outQuote:
Originally Posted by hotwaxisbad
ps i dont know what the card can go to with the temp
thanks
with thease sort of overclocks what temp is the northbrige getting are you all watercooling it.
Mine is hitting near 60c but i dont think everest is picking it up right sine its not hot to touch
As far as I know there is no nb temp sensor on these boards, just one close to the sb.
Quote:
Originally Posted by rubber5
Hoss331 is exactly right.Quote:
Originally Posted by Hoss331
Rubber try touching the south bridge heatsink whe everest shows 60c.i bet it will be very warm
my new UD3R rev 1.1 SB H/S is very hot compared to my UD3P
Oops I left out a digit. How about 1.37.:DQuote:
Originally Posted by unclewebb
I have touched the south brige heat sink but its really cool so it cant be oveheating since the northbrige only gets warm im happy about that now thanksQuote:
Originally Posted by radaja
do you see any difference in your games when you overclock your cpu becuse i dont is there any reason that is happining
8GB (4x2GB) RAM - EP45T-UD3R - Q9550 - CPU FSB : DRAM 1:2
http://img269.imageshack.us/img269/7...0515125236.png
http://img196.imageshack.us/img196/6...0515125649.png
http://img199.imageshack.us/img199/5...0515233813.png
http://img199.imageshack.us/img199/7...0515235716.png
Is the 333 strap 2.40B broke at 500fsb with th F9 bios? Should I go back to F4 or F6?
well i dont know about F9 but i do know that when running 2x2GB kits its sometimes can be hard to do but now impossible.
anyway i decided to give my new cpu a go at OCing with the stock heatsink,and i got to say im quite happy with my new cpu.
after i had to sell my awesome E3110 that could do 4250 w/1.24v-1.28v depending on the multiplier,im glad to report that my
new E8400 has gotten off to a good start.i dialed in some of my old settings from my UD3P and first try i got this.
http://i42.tinypic.com/24pmd80.jpg
i stopped it cause it was getting hot(have to adjust my airconditioner vent hose)will try again after i reconfigure some things
and some strategic fan placement to see if i can keep the temps down so i can prime for at least an hour.
To monitor NB temp use MCHTemp.Quote:
Originally Posted by Hoss331
Quote:
Originally Posted by Loco23
The temp sensor is supposedly by the SB not the NB.
well i dont game so i cant speak to that,but i would think that OCing the GPUQuote:
Originally Posted by rubber5
is what might gain you more FPS.but then again i really dont know,sorry.:(
well after some rearranging i got it to prime for over an hour:)
im going to try and lower the vcore some more and see what i get.
very very happy with this new cpu:up:
http://i39.tinypic.com/2m46m92.jpg
Thanks radaja, I have 2x1GB kit. I think I'll go back to F6 and give it a whirl. I really want that 500 FSB as the memory scores are so much better.Quote:
Originally Posted by radaja
What is your CPU reference? Cause mine is at stock which would be .760 if the VTT was at stock 1.2, and I need 1.328 vcore at that same speed (4.250ghz) to make it stable. Does increasing the CPU reference really help lower the vcore, cause I haven't tried increasing it.Quote:
Originally Posted by radaja
[QUOTE=bluestang;3790955]Quote:
Originally Posted by radaja
bluestang,yep memory scores are much better indeed.i wish i had a set of d9's right now so i could test out my new board at 2.40B ddr1200.Quote:
Originally Posted by Dark-Energy
my first one did great at that setting but my replacement for the first not so good.so i am curious as to how this UD3R will do.
Dark-Energy,for these runs my cpu ref is set to normal which sets it to 0.76
mch is at 0.70 at 1.20vtt and my vtt is at 1.26.as to helping to lower vcore it can by a notch or two.
but i think it mostly comes down to how good your cpu is.my 1.25vid cpu needed 1.34-1.36v for 4250
but my lower vids needed 1.24- 1.28v.
well it seems that 8.5x500@4250 w/1.28vcore works just fine :up:
http://i43.tinypic.com/260g1mt.jpg
and 8.5x506@4300 w/1.28 :D
http://i40.tinypic.com/2m5midi.jpg
and 8.5x512@4352 w/1.28v :D:D
http://i44.tinypic.com/23kb0cz.jpg
gonna try for 4400 w/1.28v
I just love it, most for itīs so stable, consistent and easy to tune in, i have abused it a lot and it always recover when I try to do some insane OC runs.Quote:
Originally Posted by kagula323
OC duals up to FSB 600, if you want to go higher I think you need a board with better setup, RF is to coarse.
On the downside are the heatpipe/sink for the NB, itīs not good enough if you intend to push it, recommend to go with a 3rd party heatsink with a fan or waterblock.
If I had to chose a good DDR2 board today I had probably chose the EP45-UD3R/P, some what better in overall, what about downside, hmmmm, itīs a bit more sensitivit to tune in though but once you have it tuned in and learned how it works it really rocks, donīt have 16x/16x PCIe but I donīt think that matter that much.
Otherwise I think itīs some what better in overall.
@pangingIII
Nice 4x2GB result you got. :up:
Is it with those Crucial value?
@radaja
Looks like you got your hand on a good E8400, nice. :up:
Have you got a new job or are you still searching for one?
10x allot GhostLeader ... I'm currently on UD3P ... but had the oportunity to buy an RF at verry good price but .... I'm gonna say pas :)
yep i think i got a good one indeed:DQuote:
Originally Posted by Ghostleader
and im working for an employment agency right now but the company i've been working for the last three weeks is going to hire me on full time :up:
im going to try and get 9x500@4500 today,but my cooling might not be up to the task.i've got a 4500RPM fan mounted on top of the intel stock heatsink
and the airconditioner vent hose blowing directly down from above it.to be
able to do 1hr plus prime runs ill have to crank up the heat in the house to keep the airconditioner running full time(blowing the cold stuff)otherwise this chip will shoot up to 65c and beyond.and i dont like to go above 65C.
im hoping that i can get 4500 with less than 1.34v,otherwise i think ill have to wait till i get a new cpu cooler.but im gonna try:D
not bad at all.4470 w/1.31v :D FAILED ORTHOS after 25m :mad:
http://i42.tinypic.com/nmk9ps.jpg
moving on.9x500@4500 w/1.32v :D . i think god finally granted me my very own golden cpu :D
http://i41.tinypic.com/2qleiw1.jpg
How much MCH volts will I need for 2x1GB rams @ 1200 mhz on 500fsb x8.5 ??
anywhere from 1.26 to 1.36.ive seen some do it with less than 1.30,also depends on what cpu(dual core or quad)
Nice to hear, nice to get some cash, isnīt.Quote:
Originally Posted by radaja
Keep up the good work with your gear. :)
Good idea to say pass if you already have a UD3P.Quote:
Originally Posted by kagula323
You shouldnīt need more then 1,24v but it depends on what tRD you intend to use, probably tRD 8 I think, I did run my E8400 @ FSB 500 x 8 2x1 @ 1200MHz 555 15 tRD 8 with 1,22v.Quote:
Originally Posted by bluestang
Hope this screenie can help some.
http://i282.photobucket.com/albums/k...20055515tR.jpg
thanks Ghostleader.at 9x500@4500 w/1.32 its still running too hot for my cooling.
im going to move the setup into the bedroom because the airconditioner in there
blows much more cooler air than the front room one.if i can get 5c-8c cooler then
i can see what this new cpu can really do;)
Bluestang see,i knew ive seen some use much less mch volts.great work Ghostleader
with 1.22mch :up:
@ radaja
what vid and fpo/batch is your e8400?
and i please you to post a template when u get 4500 stable :up:
kagula323,vid is 1.23 and batch is Q843A771.i got it from newegg last week
and heres my settings so far.i think the only thing i might have change
is the vcore.but ill let you know once i move the computer.
hope this helps :DCode:MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: Auto
CPU Clock Ratio .........................: 9
Fine CPU Clock Ratio.....................: +0.0
CPU Frequency ...........................: 4.50GHz (500x9)
********** Clock Chip Control ************
>>>>> Standard Clock Control
CPU Host Clock Control...................: Enabled
CPU Host Frequency (Mhz) ................: 500Mhz
PCI Express Frequency (Mhz) .............: 100
C.I.A.2 .................................: Disabled
>>>>> Advanced Clock Control [Press Enter]
CPU Clock Drive..........................: 800mV
PCI Express Clock Drive..................: 900mV
CPU Clock Skew (ps)......................: 0ps
MCH Clock Skew (ps)......................: 0ps
********** DRAM Performance Control ******
Performance Enhance......................: Turbo]
Extreme Memory Profile (X.M.P.)..........: Disabled
(G)MCH Frequency Latch...................: Auto
System Memory Multiplier ................: 2.00D
Memory Frequency (Mhz) ..................: 1000
DRAM Timing Selectable ..................: Manual
Standard Timing Control
CAS Latency Time.........................: 5
tRCD ....................................: 5
tRP'.....................................: 5
tRAS.....................................: 15
>>>>> Advanced Timing Control [Press Enter]
>>>>> Channel A Timing Settings [Press Enter]
Static tRead Value.......................: 9
>>>>> Channel B Timing Settings [Press Enter]
Static tRead Value.......................: 9
********** Motherboard Voltage Control ***
>>>>> CPU
CPU Vcore................................: 1.34 change this for your CPU
CPU Termination..........................: 1.26
CPU PLL..................................: 1.57
CPU Reference............................: NORMAL
>>>>> MCH/ICH
MCH Core.................................: 1.36
MCH Reference............................: 0.738 i think,it shows up in ET6 as 0.70
MCH/DRAM Reference.......................: NORMAL
ICH I/O..................................: NORMAL
ICH Core.................................: NORMAL
>>>>> DRAM
DRAM Voltage.............................: 2.10 change this for your RAM
DRAM Termination.........................: NORMAL
Channel A Reference......................: NORMAL
Channel B Reference......................: NORMAL
Well, I have just recieved my UD3P, the board looks nice, but like always Gigabyte thought that most of users are color-blind.
In comparison to my previous motherboard (ga-x48-ds4) this one have almost twice the options I had before. And that is good from a side and bad (just for now) from other side, because I dont know what does some of those options. And good because I can touch a little bit more.
I attach my Bios options, where I just move slightly some numbers.
And also I bring up (in red fonts) the options wich I dont know what they do, so if someone dont bother, could give me a little explanation.
Thanks in advance.
Template for Gigabyte Users
Code:******Gigabyte EP45 UD3P******
Q9650 389 X 9 3510MHz
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.35GHz...........................[ 389 x 9 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 389 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Auto ]
(G) MCH Frequency Latch.........................[ 333MHz ] ---> If I have an FSB higher than 400 I should use the 400MHz option here??
System Memory Multipler.........................[ 2.40B ]
Memory Frequency 1066...........................[ 936 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ Auto ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ Auto ]
******Channel A Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.25000 ]...................[ 1.27500 ]
CPU Termination [ 1.20 ]...................[ 1.260 ] ---> This is VTT? (Which one shouldn be over 1.35/1.40?? And also it refers to Vdrop??
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.766 ]...................[ 0.768 ]
MCH Core [1.1 ]...................[ 1.200 ]
MCH Reference [0.760 ]...................[ 0.778 ]
MCH/DRAM Refernce [0.900 ]...................[ 0.910 ]
ICH I/O [1.500 ]...................[ 1.500 ]
ICH Core [1.100 ]...................[ 1.100 ]
DRAM Voltage [1.800 ]...................[ 2.000 ]
DRAM Termination [0.900 ]...................[ 1.000 ]
Channel A Ref [0.900 ]...................[ 1.000 ]
Channel B Ref [0.900 ]...................[ 1.000 ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ] ---> I dont know where is this one.
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
@ radaja and ghostleader...thanks I'll give it a try. BTW I'm running a dual core as in my sig.
wow ... radaja ... u amaze me :P ... so quik u answered ... really apreaciate :D:up:
@radaja, So really cool You got golden CPU,I'm sure VID 1.23 isn't too hot for 4.5 on Air ,awesome clock with low volt
kagula323,no problem at all.thats why were all here to help and learn :D
BuGjAE,yea it seems to be a great chip.im trying to do 9x500 but its
just a little too hot.had to up my vcore to 1.34 and might need a little more
to get it to prime for more than an hour.dont know if my cooling can do it
now.:mad:
You don't understand me. A temp sensor is located right in the chipset, not on the board.Quote:
Originally Posted by Hoss331
Try this - http://cp.people.overclockers.ru/cgi...pBetaSetup.zip
hey loco i just installed this and i dont get it.the cpu temp works fine but the mch never moves from 42%.took the fan off of my NB and still nothing.
under loard with fan/under load without fan still 42%.am i missing something.why doesnt everest or ET6 pick up this sensor that is inside the NB?
also is there a way to change it to english?please help
heres some screenshots.i have an airconditioner vent hose blowing directly down from above
tha cpu and NB.first shot is without it about five minutes after i start my computer.
the second one is about two or three minutes after i put the vent hose on,and you can see how the cpu
temps drop but not the NB.ive got a 4500RPM fan on the cpu and a 4000RPM fan on th NB.
http://i44.tinypic.com/95x9g2.jpg
http://i40.tinypic.com/6hhw1z.jpg
Anyone want Q6600 settings? let me know :D Heres my stable 4.05GHz settings :) I have, 3.0GHz, 3.2GHz, 3.6GHz, 4.0GHz and 4.2GHz settings all stable.
Code:******Gigabyte EP45 UD3P******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.05GHz...........................[ 450 x 9 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 450 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Auto ]
(G) MCH Frequency Latch.........................[ 400MHz ]
System Memory Multipler.........................[ 2.00D ]
Memory Frequency 1066...........................[ 900MHz ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 4 ]
tRP.............................................[ 4 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ Auto ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ 2 ]
******Channel A Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ 1066MHz ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ 1066MHz ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.25000 ]...................[ 1.3625 ]
CPU Termination [ 1.20 ]...................[ 1.28 ]
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.766 ]...................[ I can't remember the number, but its 2 steps up from default ]
MCH Core [1.1 ]...................[ 1.3 ]
MCH Reference [0.760 ]...................[ I can't remember the number, but its 1 step down from default ]
MCH/DRAM Refernce [0.900 ]...................[ 1.000 ]
ICH I/O [1.500 ]...................[ 1.500 ]
ICH Core [1.100 ]...................[ 1.100 ]
DRAM Voltage [1.800 ]...................[ 2.000 ]
DRAM Termination [0.900 ]...................[ 1.000 ]
Channel A Ref [0.900 ]...................[ 1.000 ]
Channel B Ref [0.900 ]...................[ 1.000 ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Enabled ]
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
Its been a while since I last checked this thread. I am using bios f4 on my ud3r. Is f9 the best current bios to run with?
im using F6 that came with the board.seems ok
Hi radaja!
Min temp for this sensor is 50. Run MCHTemp, choose "Команды", then "Настройка" and set like this (i highlighted in red) http://img193.imageshack.us/img193/8...7325e74.th.jpg
Turn off your fan on NB. Run prime, choose "custom" and set field "Min FFT Size" to 1024. Press ok. And wait :)
No :(Quote:
Originally Posted by radaja
I can translate if you have a questions.
3.6 settings would be appreciated with your reference values. Hopefully they'll help my 1.3125 VID chip :[Quote:
Originally Posted by fatguy1992
thanks loco23.so i click the one marked in red,which then shows the temps as mch -58 and cpu as -71?Quote:
Originally Posted by Loco23
I was wrong :) Choose the first item again :)Quote:
Originally Posted by radaja
You tried to run prime? Temperature is increased?
yep i tried but still no luck.ive even tried moving the setting from 50c to -7c.but no luckQuote:
Originally Posted by Loco23
Leave all settings by default.
What you MCH Core voltage?
P45 very cold chipset. I have never seen more than 50 degrees, once installed HR05 on NB.
Try run prime about an hour, as i wrote above.
right now my mch core is at 1.30v.ill keep messing around with it.thanks for your help:)
That programs doesnt want to run for me, keeps giving me an error code 2 on install and I cant read the rest. :shrug:
i think i might try reinstalling it.i cant seem to get it to work.i just tried a blow dryer(hot air) on the NB but still no change in temp readout.
ive been primimg for an hour now,this cpu is a monster!
9x458@4124 with stock vcore(1.237v in bios/1.216v load) :up:
simply amazing:D
http://i39.tinypic.com/2i0drnm.jpg
http://i44.tinypic.com/mvomsm.jpg
Try increase MCH Core voltage to 1.5 just for test and run prime/blend again.Quote:
Originally Posted by radaja
Give me your email, i'll send old version of this program.
Or try this version - http://cp.people.overclockers.ru/cgi...HTempSetup.zip
ok i will do as soon as i stop this priming run:)
thanks again for your help.
ill get back to you in about 20 minutes.
Take a screenshot with error, maybe i can help you.Quote:
Originally Posted by Hoss331
radaja, you use Vista or XP?
i use vista.i just installed it,but it stays at 50c now.if i move the setting to say 20c,does that mean once it goes above 20c the temp sensor will move?
No.Quote:
Originally Posted by radaja
From MCHTemp's FAQ:
The sensor is not able to measure the temperature below a certain value (hereafter Tmin). Tmin depends on the specific chip, and typically lies in the range of 40 to 50 ° C, but in rare cases can reach 66 ° C. Tmin can not be determined programmatically, so MCHTemp considers it equal to 50 ° C.
With Vista maybe some problem, one moment please :)
Because the driver is not digitally signed you need to load the operating system in test mode. Also you may use Driver Signature Enforcement Overrider or ReadyDriverPlus.
is this directed to me?cause i dont have problems loading the program.Quote:
Originally Posted by Loco23
It's for all Vista users :)Quote:
Originally Posted by radaja
I use XP, never ran MCHTemp on Vista.
The first beta one you posted would give me the error but the second works fine, I guess the beta doesnt like win7.
http://i131.photobucket.com/albums/p.../Untitledv.jpg
Hoss331, fine! I'm glad that was able to help you :)
Sorry guys but I'm told there is no temp sensor inside the actual NB on the UD3P.
Armored_Kech1, sensor inside chip, not in mobo! This sensor has many chips: 945P/PL/G/GC/GZ, 946PL/GZ, P/G/Q965, Q963, G35, P35, P31, G33, G31, Q35, Q33, X38, P45, P43, G45, G43, G41, Q45, Q43, X48. This program reads the value directly from the chip, like CoreTemp reads them from the CPU.
loco23.do you know the name of the driver?
This is a hard question :) 5 sec please..
radaja - "Mama Hardware Access Driver", Path - Windows\system32\DRIVERS\Mama.sys
thanks:D
oh man i cant believe i didnt see this.:confused:Quote:
Originally Posted by Eeky NoX
thank you so much Eeky NoX.ill be getting ddr3 board next week:up:
I hope to order one in a few weeks. Have to make a tax payment in June :(. After that I hope to be able to try the ddr3 board. ThanksQuote:
Originally Posted by Eeky NoX
No problem, just two questions, what cooling are you using? and how much RAM are you using?Quote:
Originally Posted by Homeless2
Thanks
Anyway heres what I recommend, but it might change a bit once I know the answer to those two questions.
So pretty much what you do for the References is, set your CPU Termination to 1.2v (stock) then set both the CPU and MCH references to 0.760. Then increase the CPU Reference by to steps (with the + key on the num pad), and lower the MCH Reference the same way.Code:******Gigabyte EP45 UD3P******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.05GHz...........................[ 400 x 9 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 400 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Auto ]
(G) MCH Frequency Latch.........................[ 400MHz ]
System Memory Multipler.........................[ 2.66D ]
Memory Frequency 1066...........................[ 1066MHz ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ Auto ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ 2 ]
******Channel A Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ 1066MHz ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ 1066MHz ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.25000 ]...................[ 1.500 ] - I only use 1.2vcore - if stable then lower until it becomes unstable
CPU Termination [ 1.20 ]...................[ 1.30 ] - I only use 1.2v - if stable lower until it becomes unstable
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.760 ]...................[ I can't remember the number, but its 2 steps up from default ]
MCH Core [1.1 ]...................[ 1.2 ]
MCH Reference [0.760 ]...................[ I can't remember the number, but its 1 step down from default ]
MCH/DRAM Refernce [0.900 ]...................[ 50% Of the RAM Voltage ]
ICH I/O [1.500 ]...................[ 1.500 ]
ICH Core [1.100 ]...................[ 1.100 ]
DRAM Voltage [1.800 ]...................[ Whatever your RAM needs ]
DRAM Termination [0.900 ]...................[ 50% Of the RAM Voltage ]
Channel A Ref [0.900 ]...................[ 50% Of the RAM Voltage ]
Channel B Ref [0.900 ]...................[ 50% Of the RAM Voltage ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Enabled ]
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
Also if this doesn't work try different BIOSes, they can make a massive difference.
PS. sorry for the late response.
wow this ram is doing pretty good also.i bought this kit about 1 1/2 years ago.for my amd machine.
i didnt think it would OC so well.i thought maybe 950MHz.i was wrong.
http://www.newegg.com/Product/Produc...82E16820231098
http://i41.tinypic.com/2vd0cic.jpg
Quote:
Originally Posted by Ghostleader
yep, the 4x2GBs were those Crucial value kits.
my current max CPU-Z validation on my Q9550, also using the 2x2GB Crucial value kit
http://img33.imageshack.us/img33/931...0516195915.png
Quote:
Originally Posted by Eeky NoX View Post
To Radaja, Panging & OC Nub : If you wanna know what's the DDR3 version really gat in terms of potential,
just have a look sometimes on my french thread, I'm hardly workin' on it for now
http://soj.mesdiscussions.net/soj/in...jet_2430_1.htm
I think 600fsb is possible with dualie's...but the PC16000 is hard to go in the specs and I don't know if it comes because of me, the mobo or the D9s
i think i probably knew about potential of my DDR3 board by myself already, but thanks for the info that you posted at over there anyway.
anyways this's what i've found so far, one of my E8400 fairly easy go to 650FSB, another one was around 620, but they were just for some CPU-Z validations or for 1M SuperPi's.
as for Q9550, myself and friend have played with 2 EP45T-UD3R rev 1.0 and 3x Q9550's... on air-cool and 1.58v (cpu-z) vcore, they were almost maxed out booting from bios at the same 540FSB.
however, i'm not quite sure whether CPU or boards that maxed out on the fsb, and this mostly because i don't have a lot of experiences with the fsb overclocking.
Ok, since about a week ago I have been trying to get 500FSB x 8 or 8.5 with 2.4B with my new Kingston HyperX DDR2-1150 2x1GB kit. I was on F9 at the time and could not get system to boot with 500FSB 2.4B for 1200 RAM. It didn't even like 2.0B as I figured I would boot with 2.0B and then change with ET6 in XP to 2.4B. I then went back to F6 bios and was able to post but would get BSOD's or lockups loading XP. So I went back to square one to see if my RAM could even do 1200...set everything to stock 333FSB x 9.5 (3.16ghz), all voltages on auto (no LLC) except RAM @2.20v, all timings and subs auto except 5-5-5-15-2T. It boots fine with RAM at 1066 (3.20B) and MemSet comes up as PL6 and tRFC 42. So I raised FSB in ET6 to 360 (3.42ghz) to check RAM at its default of 1150mhz, I kept PL at 6, tRFC at 42 and volts at 2.20. Ran HCI Memtest for an hour and prime blend for an hour, no isues. Great I figure I would try 1200mhz, rasied FSB in ET to 375 (3.56ghz), raised vcore to 1.3 and still kept PL at 6, tRFC at 42 and volts at 2.20. Ran HCI again for about 45min to 1 hour and then Prime Blend. Prime was at about 1-1/2 hours and then I went for a walk. Came back and blue screen crash. Hit reset button and then had a continous loop reboots unitl I turned power off. So it crashed anywhere from between 1-1/2 to 2 hours.
Am I right in thinking that RAM is probably good for 1200, but PL needs to be raised along with tRFC and volts? 1.30 vcore should have been plenty for 375FSB x 9.5 right? I'll start with some of you guys 500 2.4B templates tonight hopefully. Thanks.
whats your mch voltage at?
Double.Delete pls.
http://www.xtremesystems.org/forums/...4&postcount=81
http://www.xtremesystems.org/forums/...&postcount=142
http://www.xtremesystems.org/forums/...&postcount=148
http://www.xtremesystems.org/forums/...&postcount=161
http://www.xtremesystems.org/forums/...&postcount=177
http://www.xtremesystems.org/forums/...&postcount=238
http://www.xtremesystems.org/forums/...&postcount=259
http://www.xtremesystems.org/forums/...&postcount=299
http://www.xtremesystems.org/forums/...&postcount=329
http://forums.tweaktown.com/f69/bios...h-guide-27576/
http://www.xtremesystems.org/forums/...&postcount=555
http://www.xtremesystems.org/FORUMS/...&postcount=666
http://www.xtremesystems.org/FORUMS/...&postcount=780
http://www.xtremesystems.org/FORUMS/...&postcount=799
http://www.xtremesystems.org/FORUMS/...&postcount=831
http://www.xtremesystems.org/forums/...&postcount=822
http://www.xtremesystems.org/forums/...&postcount=831
http://www.xtremesystems.org/forums/...&postcount=986
http://www.xtremesystems.org/forums/...&postcount=992
http://www.xtremesystems.org/forums/...postcount=3128
This is about all you need to know about OC on this board.Read these posts.:up:
Also best bios for me was F4 because i got stability with 500fsb at 1.24V Mch.
Brutal! Thanks for the advice. :up:Quote:
Originally Posted by h3x0r_1984
I left it at stock for that test. I know it will need to be higher at higher FSB.Quote:
Originally Posted by radaja
Thanks H3 :up: I too thinks its either F6 or F4 for BIOS. I just need to get these settings just right!Quote:
Originally Posted by h3x0r_1984
Nice summary!
I'm considering getting a Q9650 now, I want quad. :(
Well...my UD3P was making stability for 450fsb at 1.4Mch , 1.45VTT and 1.7PLL....and i decided i was way too high after what i have seen through this thread.Quote:
Nice summary!
So i started reading this thread.I'll hopefully continue going through it and find out all the ram OC secrets.
i have 2x2gb 800mhz ddr2 memory its the corsair pro with the lights on it
I was wondering what peapole has been overclocking it to becuse when i overclock my q9450@3.5ghz it goes to 875mhz but i dont touch the latencies will it run for a few years or not or will it burn it out soner rather than later
thanks
Just sharing my latest template after a 24hr Prime Blend test (Slected custom and bumped RAM used up to 3200), the load temps are pretty stable at 54°C ą2°C with my new TrUE Black 120 installed. I am now considering trying to get the RAM down to 4-4-4-12 at this speed...
Code:*************************************
*************************************
Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9
*************************************
*************************************
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [Fast]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.10GHz( 456x9)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [456]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: [Auto]
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).....800.........: 900
DRAM Timing Selectable (SPD)..........: [Manual]
>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 4]
x tRP.............................5...: [ 4]
x tRAS...........................18...: [12]
>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [ 4]
x tWTR............................3...: [ 4]
x tWR.............................6...: [ 8]
x tRFC...........................52...: [68]
x tRTP............................3...: [ 4]
x Command Rate (CMD) .............0...: [ 2]
>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............11...: [ 9]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............11...: [ 9]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
****** Motherboard Voltage Control ******
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Disabled]
CPU Vcore..............1.27500V.......: [1.30625V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.570V]
CPU Reference..........0.760V.........: [0.835V]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.200V]
MCH Reference..........0.760V.........: [0.778V]
MCH/DRAM Reference.....0.900V.........: [0.910V]
ICH I/O................1.500V.........: [1.590V]
ICH Core...............1.100V.........: [1.200V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.080V]
DRAM Termination.......0.900V.........: [Auto]
Channel A Reference....0.900V.........: [Auto]
Channel B Reference....0.900V.........: [Auto]
******** Advanced BIOS Features ********
Hard Disk Boot Priority...............: [Press Enter]
First Boot Device.....................: [USB-HDD]
Second Boot Device....................: [Hard Disk]
Third Boot Device.....................: [CDROM]
Password Check........................: [Setup]
HDD S.M.A.R.T. Capability.............: [Enabled]
Limit CPUID Max. to 3.................: [Disabled]
No-Execute Memory Protect.............: [Enabled]
CPU Enhanced Halt (C1E)...............: [Disabled]
C2/C2E State Support..................: [Disabled]
x C4/C4E State Support................: Disabled
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.....................: [Disabled]
Virtualization Technology.............: [Disabled]
Delay For HDD (Secs)..................: [ 0]
Full Screen LOGO Show.................: [Disabled]
Init Display First....................: [PEG]
******** Integrated Peripherals ********
USB Keyboard Function.................: [Enabled]
USB Mouse Function....................: [Enabled]
USB Storage Function..................: [Disabled]
h3x0r_1984,thanks for finding these post and giving us quick links.:D
good to see that you take the time and re-read through the thread.
i find myself doing at least every other day.:up:
again thanks.
also heres two more very informative post from lsdmeasap
http://www.xtremesystems.org/forums/...postcount=1157
http://www.xtremesystems.org/forums/...postcount=1023
Well this is waht I got... and... Im getting a bigger headache...
Those settings were stable at prime95 for 6hs, also It pases SuperPi 1m, 2m, 32m.Code:******Gigabyte EP45 UD3P******
Q9650 423 X 9 3800MHz
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.35GHz...........................[ 423 x 9 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 423 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 700mv ]
PCI Express Clock Drive.........................[ 700mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ 266MHz ]
System Memory Multipler.........................[ 2.50A ]
Memory Frequency 1066...........................[ 1058 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Motherboard Voltage Control******
Load-Line Calibration [Disabled]
CPU Vcore [ 1.200 ]...................[ 1.37500 ]
CPU Termination [ 1.20 ]...................[ 1.260 ]
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.766 ]...................[ 0.853 ]
MCH Core [1.1 ]...................[ 1.240 ]
MCH Reference [0.760 ]...................[ 0.838 ]
MCH/DRAM Refernce [0.900 ]...................[ 1.050 ]
ICH I/O [1.500 ]...................[ 1.500]
ICH Core [1.100 ]...................[ 1.100]
DRAM Voltage [1.800 ]...................[ 2.10 ]
DRAM Termination [0.900 ]...................[ 1.050]
Channel A Ref [0.900 ]...................[ 1.050]
Channel B Ref [0.900 ]...................[ 1.050]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ] -----> I dotn know where is this one
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Enabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
But... there is some options which I dont know what they are like the ones on "advance clock control" and the options for MCH and the last ones for CPU, at the side of valtages.
But whatever, I will reed more, but I would like to know which ones for you should be the best settings to get 4ghz, that is what I want to begin :D
Thanks in advance.
try this and just see if it works.
http://www.xtremesystems.org/forums/...postcount=2070
You shouldn't need to change your clock drive voltage but sometimes 800/900mv can solve problems. Clock skews also help when doing high overclocks as some components especially the CPU and MCH will drift out of sync so adding a picosecond delay to it can work for fine tuning
Ok, so after reading over past threads and settings you guys (you know who you are!) suggested. I went back to F6 and after many boot attempts this is what I got tonight. It's a start. I'm not happy with my vcore though and PL9 needs to be lower. I think these will do PL7 with the right settings elsewhere! Tomorrow I will shoot for PL8 and 8.5 cpu multi for 4250.
BTW, I could not boot into XP succesfully until I lowered vdimm in BIOS from 2.30-2.36 (mfg suggested is 2.30-2.35) to the value below. Go figure, it wanted lower volts!
Any more suggestions is welcome and thanks again everyone!
http://img527.imageshack.us/img527/625/8x5001200pl9.jpg
Thanks, now Im testing 4ghz 9x 423.
The problem was an 8 on Performance level, thus I couldnt boot, but now I have a 9, and its running properly
Well I tried those settings and its boots properly but it wasnīt stable... thus I got BSOD.... aaaaaaaaaaaaaaaaaand it is getting up my nerves.Quote:
Originally Posted by radaja
I think the problem could be the ram, dispite (to my way of thinking) the high VID I have, which is 1.25000 and maybe I need more vcore... but with 1.4000 set on bios it wasn't stable.
So what you think ?
Osterman, I have a 1.25vid q9650 also. I put it back in tonight to mess with. Have not run Prime yet but ran LinX and passed with these settings. You could also try the 2.00D PL9 if you are unsure about your ram.
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
CPU Frequency .........................: 4.20GHz (467X9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 467
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]
Advanced Clock Control
CPU Clock Drive........................: 800mV
PCI Express Clock Drive................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance....................:Standard
Extreme Memory Profile (X.M.P.)........: Disabled
(G)MCH Frequency Latch.................: Auto
System Memory Multiplier ..............: 2.40b
Memory Frequency (Mhz) ................: 1121MHz
Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15
PL8
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
CPU Vcore..............................: 1.35625v
CPU Termination........................: 1.30v
CPU PLL................................: 1.45v
CPU Reference..........................:0.848
MCH/ICH
MCH Core...............................: 1.320v
Reference..............................:0.863
MCH/DRAM Ref...........................: Normal
ICH I/O................................: Normal
ICH Core...............................: Normal
DRAM
DRAM Voltage...........................: 2.10 (whatever your ram is rated)
DRAM Termination ......................: Normal
Channel A Reference....................: Normal
Channel B Reference ...................: Normal
hey guys, i know some variant of this question's been asked various times over here, but are the ud3r boards still neglected for bios updates? Last i read, UD3P is up to F9l but what about the UD3R? Seems like most people agree the UD3R clocks as well as the UD3P, which is really the main concern of mine; i don't need crossfire and all the extras UD3P has got to offer, so going for the UD3R should be a better ($$$) choice i hope?
Both the UD3P and UD3R are official at F9 (with the same bios change description) so there itīs no different, the F9l for the UD3P is not official.Quote:
Originally Posted by noinimod
Some say that UD3P have higher priority then the UD3R when it comes down to bios fix but I doubt that.
UD3R is good choice if donīt want the extra bling bling.
this is my first time running linpack on my Q9550+EP45T-UD3R
(thanks to Dua|ist for this LinX program)
http://img34.imageshack.us/img34/835...0520195527.png
CPU's temp/voltages info... at before running LinX
http://img195.imageshack.us/img195/1...0184800.th.png
http://img188.imageshack.us/img188/8...0184821.th.png
CPU's temp/voltages... during running LinX
http://img35.imageshack.us/img35/245...0190908.th.png
http://img34.imageshack.us/img34/391...0190953.th.png
and then i shutdown the computer and restart it, and rerun LinX...
http://img193.imageshack.us/img193/6...0520224452.png
rest of the bios settings were 800/900/0/0, Turbo, Strap 333, DDR3-1600, 7-7-7-20-auto's, DDR3 Write Levelling/Write Training: Disabled
@pangingIII
Nice work :up:
LinX is a nice app isnīt.
Whatīs up with the different in time and GFlops between the runs ~42 GFlops compare to ~60 GFlops, same core speed, bus speed, ram speed, timing, problem size and memory use. :confused:
Hi Ghostleader,
i probably had something running at the time? or something? i'm really not sure what was causing them to be like that.
here's another one that i ran it at 4.0GHz
http://img43.imageshack.us/img43/734...0520154217.png
CPU's temp during running LinX.
the room was kinda warm, no air con at the time that i ran this test.
http://img35.imageshack.us/img35/816...0150619.th.png
I know, it can really get hot with LinX, need to have good cooling. What kind of cooling do you have on that quad.
True Ex with 2 fans.
my system is usually using in an air-con room so the core temp usually never got that high,
if it has to be in full load more often than it is now i'll consider improving the core temp, i think.
Ghostleader, how old are those Hyperx PC2-9600's in you sig? Just curious as I just got some PC2-9200 from Newegg.
bluestang post some results with that memory and tell us if they are D9. I think u are getting 2x1GB sticks.Quote:
Originally Posted by bluestang
kagula23, will do as soon soon as I can get 500fsbx8.5 stable. I already have them installed since the weekend. I haven't taken off the heatspreaders though to look at the chips. I think the are Elpida though, not D9. I'm afraid to try and take off heatspreaders!!Quote:
Originally Posted by kagula323
Well I tried a couple of things.
And I still getting BSOD, voltages... I dont think so, I think the problem are ram.
Could you people tell me which settings did you use for 2x2gb 1066mhz (that is what I have).
By the way, I can get stability with 3.8 423x9, but I cant have it with 4ghz (450x9= 4.05, 445x9= 4ghz, 471x8.5= 4ghz, 500x8=4ghz) I CANT!!!!! AND IT'S DISTRUBING jaja.
Thanks.!
Osterman, I have 2 sets of this http://www.newegg.com/Product/Produc...82E16820231246 Both sets do at least 1130mhz 2.10v, PL8. I think it has to be settings, most all of these cpu's will do over 4.0ghz. Have you tried dropping the CPU multi and just testing ram to see what it will do? That will give you a better idea what the problem may be.
I have 1 set of this http://www.newegg.com/Product/Produc...82E16820231166
And those settings you have are for 24/7??
I bought two set of 2x1 in november 2007 and they are Micron D9GKX and they got really hot with the original heatspreader, did a 100% stresstest (HCI design Memtest) @ 1200 555 15 2.30V) and placed a temp sensor inside and got a temp ~65C, not good I thought.Quote:
Originally Posted by bluestang
Placed 2 60 fans@1700rpm (donīt like noice, therefore not higher) above the ram and got a temp ~55C, not good either.
I bought myself some Nexus Heat Pipe Memory Cooler (looks like OCZīs Reaper) and replaced the original heatspreaders, same kind of stresstest and got a temp ~40 without fan, I have not tested with fans because Iīm pleased with that temp, my ambient room temp was ~21.
Removing the heatspreader was rather easy, have to be careful though, I did the same to a set of 4x1 Kingston HuperX PC8500 (Elpida IC) no problem there either but when I tried it on a set of OCZ Titanium Alpha VX2 the IC came lose, tough luck but thatīs the way itīs some time.
http://www.nexustechnologyusa.com/nt...hxr-5500bl.jpg
i rerun LinX after changing a few bios settings for my q9550 at 4.0GHz
http://img34.imageshack.us/img34/172...0521200219.png
btw, Ghostleader, what's wrong with your UD3P?