**Official DFI LanParty UT X48-T2R(and LT) Discussion

Quote:

---

Originally Posted by gersson

SHIz, as soon as I read that my heart sank. I'm really insecure about this chip. I hope to the gods it's a good one. my old e6700 did 3.5 @ 1.55v :(

No deal! Get yer dirty hands off my baby :D

the intel bunny looks like a disco dancer :ROTF:
'...dancing!'

---

:D Was just messing with you and a bit of Envy showing thru :)

Question that I Should know but eludes me right now; Can I run a 1x PCI-E device,( Network adapter), in a 4X PCI-E slot,( ie the lower slot on the x48)?? Reason being, I really do not like the Marvell Lan drivers, and would like to try out this Intel Pro/1000 PT adapter.
The 1x slot is a no go for me as I have a Water Block on my Vid that the adapter would hit.
Any and all info would be Highly appreciated.I am putting off my install until tomm due to this, as thats how much I hate the onboard lan :)

Larry

if u use 1x/1x and not 4x mode in the bios then i think that u can

Quote:

---

Originally Posted by zanzabar

if u use 1x/1x and not 4x mode in the bios then i think that u can

---

Cool TY for that. I think I'll try that tomm. I sorta remember that as long as the card fits it will work, but I want to make sure. It's a bit of a pain to remove stuff in my case, as when I built it I should have made it 1" wider, as my fingers are too big to reach the thumb screws with the water lines in the way:(

Larry

Does anyone have any pics of the DFI LANPARTY UT-X48-T2R motherboard just want to know for sure what sort of cooling does this ship with? Also is it attached to the board, if so how hard would it be to remove for WC? I know the LT version comes with an attachable northbridge heatsink, but a little confused about the UT :confused:

hardtarget, I believe that both UT versions of X48 are the same except for one being a DDR3 board...the pictures in this thread already show what it will look like (the one with the rear external heatsink). The LT is the same exact board except for the cooling sinks being different. The X48 LT board is identical to the X38 LT board. Even the cooling is identical.

The Transpiper that was used on the P35 was later available online. The problem was, that most tests people did here showed that it made no difference at all. I'm sure the new Transpiper will also be available as a standf alone product down the road. It's probably wiser to get the LT version to save money now. If the new Transpiper turns out to be really worth it, suck it up and buy it as a stand alone later on. At least by getting the LT, you could buy a whole arrary of aftermarket sinks made for the north and southbridges.

I own the P35 UT board and just ordered the X48 LT board...I am happy with this now (was going to go X38 LT) but should have waited and gotten the P35 LT board back then to save $$$. I am mainly getting this board because my new Dominator 4gb kit doesn't work with the P35 UT board and I want to have 4gb before I make the switch to DDR3 (probably when Nehalem comes out).

Quote:

---

Originally Posted by rioja

wait a second, what is with 3870x2? i'm getting it right now
is it only issue with asus HD3870x2 4DVi ROG version?

---

yup
its that pcie 1.0a issue.
since the mars, p35UT, and this board all had it..

sishhh regretted buying that card.. even though it was a fluke that i got the only one that came into malaysia .

a card that loves asus pcie 2.0 mobo sish.. wth!!

ah decided to sell the card..

Quote:

---

Originally Posted by hardtarget

Does anyone have any pics of the DFI LANPARTY UT-X48-T2R motherboard just want to know for sure what sort of cooling does this ship with? Also is it attached to the board, if so how hard would it be to remove for WC? I know the LT version comes with an attachable northbridge heatsink, but a little confused about the UT :confused:

---

thats the picture on the main page
the NB is just with that large heatsink with the fan clip

Quote:

---

Originally Posted by gersson

I just got this puppy in the mail:


Too bad my board comes in on Wednesday -- making it the very last part that comes in :(

Any thoughts on all them' pretty numbers?

---

Can't wait to see your clocks. I just ordered the same cpu. I will be putting it on the P35 version of your board.

Pushing 8 multi for FSB here.Open window.Voltages not tweaked.

http://i126.photobucket.com/albums/p...hotos/5261.jpg

I'd like to see how is going to handle a quad.
I dont believe it's going to have any difference than the x38:shakes:

I've got a x3350, this board and 8gb Redline on the way... I'll be pairing this up with an IFX-14, and 2 HR05 SLI/IFX's... I'll post some pics and benchmarks hopefully by Friday... hoping for 3.8+ ghz :D

Quote:

---

Originally Posted by RedHOT

I've got a x3350, this board and 8gb Redline on the way... I'll be pairing this up with an IFX-14, and 2 HR05 SLI/IFX's... I'll post some pics and benchmarks hopefully by Friday... hoping for 3.8+ ghz :D

---

Good luck, man

Of course, I wish you luck because I hope some of that luck will rub off on my chip ;)

hey mushkin hq informed me that they wont be producing the redlines 4gb version for the time being as micron is having some issue with supplying them their chipsets..

so u must have gotten it from a retailer with ready stocks.

Quote:

---

Originally Posted by Forsaken1

Pushing 8 multi for FSB here.Open window.Voltages not tweaked.

http://i126.photobucket.com/albums/p...hotos/5261.jpg

---

Looking good...I'm very happy right now with my E8400 which is doing 4.2ghz 24/7 with a pretty low 1.35 vcore and 1.28 vtt. Hopefully the X48 can do similar...I just hope my Dominator 4gb kit works ok with this board.

Thanks Ace76.This cpu has done 4.6+ prime stable for hours,on a p35.Boot into windows at 9x575FSB.Either i have not found the right settings yet or im at the limits of this board with my combo.1:1(333/667) ratio on ram is tough with this board.Runs best for me at 5:6(333/800).My ram is "only good:D " for 12xxMHz or so.

Put way to much voltage everywhere to make the screen shot happen.Got frustraded and thru the kitchen sink at it.It stuck.Will play some more latter tonight and work on voltages.Looking forward to your results and others.Mine is a work in progress.Maybe more time will help.

Quote:

---

Originally Posted by Forsaken1

Thanks Ace76.This cpu has done 4.6+ prime stable for hours,on a p35.Boot into windows at 9x575FSB.Either i have not found the right settings yet or im at the limits of this board with my combo.1:1(333/667) ratio on ram is tough with this board.Runs best for me at 5:6(333/800).My ram is "only good:D " for 12xxMHz or so.

Put way to much voltage everywhere to make the screen shot happen.Got frustraded and thru the kitchen sink at it.It stuck.Will play some more latter tonight and work on voltages.Looking forward to your results and others.Mine is a work in project.Maybe more time will help.

---

Have you messed around with the GTL settings? I know that helped me a lot when I was tweaking my DFI P35 UT...once you find the right number, you should be able to lower your vcore and vtt and still have same or higher clocks. I'm sure newer BIOS revisions will help too.

The northbridge heatsink has a spot for a fan on it but there was not one that came with the board. Any recommendations on what type of fan i should put on it?

My XP1700@2.57 is finally getting tuned off next week. It is being replaced with what is in my sig :)

Everything has shipped, so with luck, I will have everything here by Wednesday and post some OC results later in the week!

Quote:

---

Originally Posted by PnoT

The northbridge heatsink has a spot for a fan on it but there was not one that came with the board. Any recommendations on what type of fan i should put on it?

---

I'm in the same boat :yepp:

Tryed a little on gtl.Default is 110(e8400).Tryed 108-112.Also NB gtl.I had the ut p35.This appears to be a little different. I dont mind sharing my journey through bliss.Hope it helps someone down the line.

NB fan appears 60mm would mount with clips.,i have a 80mm resting on NB.Need to install MCW30 soon.Although temps are not a issue.

Great to hear seraphi.Welcome aboard:up: .

Quote:

---

Originally Posted by Forsaken1

Tryed a little on gtl.Default is 110(e8400).Tryed 108-112.Also NB gtl.I had the ut p35.This appears to be a little different. I dont mind sharing my journey through bliss.Hope it helps someone down the line.

NB fan appears 60mm would mount with clips.,i have a 80mm resting on NB.Need to install MCW30 soon.Although temps are not a issue.

Great to hear seraphi.Welcome aboard:up: .

---

Got mine running anyway, coupla quick questions tho; you say 108/112 I would guess that is 1st and 2nd Cpu GTL's correct? What about the NB GTL?

Reason I ask, is that my GTL's were very limited on the board in my sig, highest was 67 and I had this setup at whats in my sig, 24/7 but seem to have hit a wall at 480ish right now. Tried higher NB volts, and higher CPU volts, not the add on, just direct, I have VDoop Enabled so far, and my VTT is still at 1.1v. Running Orthos Blend as I type with no probs, but will not boot at 485. Gotta be something I am missing, will check TRFC now.

Larry

Has anyone heard anything about the T3R version (DDR3 version of same board)? DFI websites lists it but there is no picture and no retailers seem to have it? Just curious because I've yet to see any DDR3 DFI boards anywhere, even in the forums?

Quote:

---

Originally Posted by Big Lar

Got mine running anyway, coupla quick questions tho; you say 108/112 I would guess that is 1st and 2nd Cpu GTL's correct? What about the NB GTL?

Reason I ask, is that my GTL's were very limited on the board in my sig, highest was 67 and I had this setup at whats in my sig, 24/7 but seem to have hit a wall at 480ish right now. Tried higher NB volts, and higher CPU volts, not the add on, just direct, I have VDoop Enabled so far, and my VTT is still at 1.1v. Running Orthos Blend as I type with no probs, but will not boot at 485. Gotta be something I am missing, will check TRFC now.

Larry

---

Larry,

Do not guarantee this is prime stable.Can say super 1m.

I tryed all three gtl settings.I tryed from 108 to 112 on each of the bios settings referring to gtl.RGone at DFI Club has this board now.I'm sure he will shed some light on this in the upcoming days.

Going up to 470fsb takes little voltage changes,in fact most settings can be left in auto(dual core).470-500FSB was a moderate bump in cpu vtt,NBv and SBv core.Over 510FSB is taking what i consider alot of volts to get the job done.

Here is what i ran for 8x501.E8400.Your mmv.
Cpu vid 1.275v
Vid special Auto
Ram 2.1v for me may differ for your make/model.
SB core 1.64v
NB Core 1.405v
Cpu vtt 1.2v
Vcore drop enable
Clock gen 3.45
Gtl buffer strong
GTl ref disabled
Boot up buc Auto
Dram 333/667 1:1
5-5-5-15-42
Enhanced data tranfer: Fast
Rest of ram settings auto.

Roger,i hear april'ish for the X48 DDR3 version.Need to make a bios template:).

Quote:

---

Originally Posted by Forsaken1

Larry,

Do not guarantee this is prime stable.Can say super 1m.

I tryed all three gtl settings.I tryed from 108 to 112 on each of the bios settings referring to gtl.RGone at DFI Club has this board now.I'm sure he will shed some light on this in the upcoming days.

Going up to 470fsb takes little voltage changes,in fact most settings can be left in auto(dual core).470-500FSB was a moderate bump in cpu vtt,NBv and SBv core.Over 510FSB is taking what i consider alot of volts to get the job done.

Here is what i ran for 8x501.E8400.Your mmv.
Cpu vid 1.275v
Vid special Auto
Ram 2.1 for me may differ for your make/model.
SB core 1.64v
NB Core 1.405v
Cpu vtt 1.2v
Vcore drop enable
Clock gen 3.45
Gtl buffer strong
GTlref disabled
Boot up buc Auto
Dram 333/667 1:1
5-5-5-15-42
Enhanced data tranfer: Fast
Rest of ram settings auto.

Roger,i hear april'ish for the X48 DDR3 version.

---

Thank You :) Looks like your vtt and SB are higher than mine, other than that, same as here. I'm running the X48 as well and with my E3110. Wierd thing is that SG dosn't show the NB volts higher when I raise them. I did nudge the vtt up just a tad as in SG running 10kfft and or Blend the vtt would flex from 1.1v to 1.08v, now it is a steady 1.1v in SG. I am now using Setfsb and am at 485, just want to check it in windows, as 485 was a no boot for me before which I find odd.

Another odd thing is that on my board in the sig, I ran my GTL's as 63/63/67 and it was happy as a kid in a candy store/shrug, new board/new settings. Thanks again and I'll update if I can get this thing to boot higher.

Larry

Thanks Forsaken1, much appreciated!

Welcome guys.

Have booted into windows from default bios settings straight to 520FSB.Then i use set FSB.SG is in the ballbark for me on NBv.

New board.New challange.Would be boring if it was same old same old:).

Good read,hope it is updated for this board.I think Praz was invovled with it.
http://www.edgeofstability.com/artic.../gtl/gtl1.html

Quote:

---

Originally Posted by Forsaken1

Welcome guys.

Have booted into windows from default bios settings straight to 520FSB.Then i use set FSB.SG is in the ballbark for me on NBv.

New board.New challange.Would be boring if it was same old same old:).

Good read,hope it is updated for this board.I think Praz was invovled with it.
http://www.edgeofstability.com/artic.../gtl/gtl1.html

---

I have that article downloaded :D I am going the opposite way with my GTL's. I have them at 72/73/72 right now. Boots either way at 485fsb, raised the NB a bit and have the CPU volts at 1.275v which is just a tad up. VTT is 1.109v and havn't touched the PLL yet. Old board defaulted to 1.55v on the PLL, this 1 jumps from 1.51v to 1.640v, kinda high there if I was going 1.640v as I heard the highest recomended for 24/7 was 1.15v.

I have read up on GTL's alot, and read that the GTL tables that are on that site are for 65nm chips, and that the percentage for 45nm chips is closer to 63%. I have it at 65% of what my VTT is set to and will see if she stays stable.

Another little tidbit is that on my old board in my sig, Everest stated Performance level when set to Auto was "8" this board set it to "9", of which I changed in bios settings. I am bound and determined to get my 24/7 clock back with this board and hopefully with lower volts. I had 1.34v Load for my cpu on the old 1 at 4300, I would think this 1 would do it too.

Larry

63% is the target reference for 45nm processors. Confirmed good GTLREF vs VTT settings in the X38 thread is going to be real close for this board.

See now Praz, I saw you wrote that :) Thank You. I am using the 65% right now and doing ok, got it to 8.5x490 now, she wanted more NB voltage with the 2x2gb sticks, about the same as my other board. So far, it clocks very close to the DK P35 T2RS. Maybe with a tad less voltage to.

Larry

OK, Got it back up to 8.5x500, Passes 10kfft's for a quick 5 minute run so far at 1.344v/1.32v Load. Same as my old board. GTL's set to 70/69/70 with VTT set to 1.109v.

Interesting part that I am sure a bios update will cure is that the board Over volts the CPU voltage by .032v, and Under volts the ram by .06v and Under volts the NB by .026v. These are not taken with a Meter, but do sorta coincide with my old settings on the P35 that were known good. Just thought I would throw that out there and will be testing overnight for a check on stability.

I have to say 1 thing tho, with the Enzotech WB on the NB, I have not seen my temp over 19C while running Orthos yet. Thats with water at about 52f in the rez tho. Great board so far!

Larry

Did not reach goal of sub 10 second superpi 1m tonight.Tomorrow it will fall:).
Thanks for GTL tips:up: .Going to have to put the MCW30 on.

http://i126.photobucket.com/albums/p...tos/5003-1.jpg

Quote:

---

Originally Posted by Big Lar

I have to say 1 thing tho, with the Enzotech WB on the NB, I have not seen my temp over 19C while running Orthos yet. Thats with water at about 52f in the rez tho. Great board so far!

Larry

---

WoW thats great folks where complaining about Enzo covering only 85% of the NB surface! Great temps...

You guys are making me miss my setup soooo bad!!! I'm still waiting on NB wateblock :-( Looks like my board will only live on Monday!

hmm tested yesterday running at 450.. NB around 1.41v for 900mhz CL3-4-3-9 trd 6...

NB temps on passive cooling ( not really cause its touching my coolitfreezone block.. lucky ) only 29C.. in freaking malaysia..similar with maximus on water would get around 38C.
hey somebody told me that the x48 are 65nm while all the 3 series are 90nm..

Okay guys im looking to get my first DFI board, having to import it from Motherboard PRO so i must get my purchase right first time!

Been looking at the X38 varient and its great as the layout suits me with PCI-E 16X graphics slot is highest up it can go means i dont need to move my HD rack then!


Was prompted recently by my friend that a X48 DDR2 varient exists i was like...:shrug: :rofl:

But then i see it does exist!, so why not get the higher Binned chipset then if its only $20 more!... but then i see the layout has the PCI-E graphics slot down a peg.. which is no use to me.....


But then i find there is two versions of the DDR2 Varient... LT and UT... actually theres more then a cooling difference between the two the layout of slots changes too!!


LT http://www.dfi.com.tw/Upload/Product...R_front(b).jpg


UT
http://www.dfi.com.tw/Upload/Product...%20X48-T2R.jpg




So the LT for layout purposes is the one i need to get!... can someone please confirm that the picture is correct and the top PCI-E 16X slot is in the very top location?

DFI does not have a DDR2 board that looks like this:
http://www.dfi.com.tw/Upload/Product...%20X48-T2R.jpg

If you get a DDR2 board it will look like this:
http://www.dfi.com.tw/Upload/Product...R_front(b).jpg

I spoke with someone @ DFI about this because it really pissed me off when I ordered my x48 T2R thinking I would have enough room by the NB for a good cooler, only to come to find out that it will not because they screwed up the pics.

how does this motherboard work with quads and how do you compare it with the asus boards?Which is better?
I am asking because I will build a setup with a QX9650 and I am not decided on the motherboard

So whats the word on this board you guys like it???;)

Come to my House yesterday.......DFI LP LT X48 T2R :) :)

http://img397.imageshack.us/img397/9135/boardtk4.jpg

http://img291.imageshack.us/img291/5403/bundleod4.jpg

http://img213.imageshack.us/img213/961/chipsetbw5.jpg

My testing with E 8500 ES and Q6600.......

http://img214.imageshack.us/img214/7595/e8500spilq0.jpg

http://img84.imageshack.us/img84/630...dmark01pu7.jpg

http://img84.imageshack.us/img84/552...dmark03ys4.jpg

http://img80.imageshack.us/img80/7686/q6600spi8muv0.jpg

http://img85.imageshack.us/img85/982...dmark06ol2.jpg

Quote:

---

Originally Posted by CoolZone

how does this motherboard work with quads and how do you compare it with the asus boards?Which is better?
I am asking because I will build a setup with a QX9650 and I am not decided on the motherboard

---

Same here :D I'm still not sure if I should go with the DFI X38 or better X48...

Quote:

---

Originally Posted by Psycho_eddie

Okay guys im looking to get my first DFI board, having to import it from Motherboard PRO so i must get my purchase right first time!

Been looking at the X38 varient and its great as the layout suits me with PCI-E 16X graphics slot is highest up it can go means i dont need to move my HD rack then!


Was prompted recently by my friend that a X48 DDR2 varient exists i was like...:shrug: :rofl:

But then i see it does exist!, so why not get the higher Binned chipset then if its only $20 more!... but then i see the layout has the PCI-E graphics slot down a peg.. which is no use to me.....


But then i find there is two versions of the DDR2 Varient... LT and UT... actually theres more then a cooling difference between the two the layout of slots changes too!!


LT http://www.dfi.com.tw/Upload/Product_Picture/LT%20X48_T2R_front(b).jpg


UT
http://www.dfi.com.tw/Upload/Product...%20X48-T2R.jpg




So the LT for layout purposes is the one i need to get!... can someone please confirm that the picture is correct and the top PCI-E 16X slot is in the very top location?

---

The LT does in fact have the x16 PCI-E slot at the very top, with the short 1x slot right below it.

The Enzotech SNBW-SLI block does Not afford 100% coverage,I'd say about 85% is correct. If it was square it would be better, however the heart of the heat is in the center and it handles it just fine.
The block itself is small and having the ability to swap the mounting plate around rather easily is a major plus to me. That means in my situation that I get a bit better air flow to the rear sink on the pwm's. Now to find a block to fit that.

Larry

My concern is the following:
I am planning to buy a QX9650.Is this board good for quads or not?
I am also going to pair it with a Thermalright Ultra 120 Extreme.Does it fit if it has that custom cooler on the NB?
How does it work with 4x1GB Crucial Ballistix DDR1000?I already have the Ram and I do not want to have any problems.
The DFI offer for X48 seems very interesting and I am asking the professionals what should I buy.

Quote:

---

Originally Posted by seraphi

DFI does not have a DDR2 board that looks like this:
http://www.dfi.com.tw/Upload/Product...%20X48-T2R.jpg

If you get a DDR2 board it will look like this:
http://www.dfi.com.tw/Upload/Product...R_front(b).jpg

I spoke with someone @ DFI about this because it really pissed me off when I ordered my x48 T2R thinking I would have enough room by the NB for a good cooler, only to come to find out that it will not because they screwed up the pics.

---

Okay then the UT and LT have the same layout (My ideal layout with Graphics slot @ the top)

But now im back to problem of what to get!!! ... what does UT offer over the LT??

As has already been noted the linked picture is not representative of the UT X48 DDR2 board. If I was wanting a DDR2 version of the X48 chipset I would be ordering what is presently available (LT X48) and not waiting on a future product that may or may not see the light of day.

Quote:

---

Originally Posted by Praz

As has already been noted the linked picture is not representative of the UT X48 DDR2 board. If I was wanting a DDR2 version of the X48 chipset I would be ordering what is presently available (LT X48) and not waiting on a future product that may or may not see the light of day.

---

So the UT DDR2 varient isnt even out yet?, if so then i have my awnser

X48 LT DDR2 here we come :up:

Quote:

---

Originally Posted by Psycho_eddie

So the UT DDR2 varient isnt even out yet?

---

Nope it really is as close to correct as what 'praz' said above. LT X48 version if you want one now for sure.

Quote:

---

Originally Posted by RGone

Nope it really is as close to correct as what 'praz' said above. LT X48 version if you want one now for sure.

---

Thanks for that... :shakes:


Both UT and LT boards have same layout as i have found out... my question now is as both have same layout...


What other features does the UT offer over the LT? differences?

Also only wanted to clarifiy if UT was even stocked yet... if its not then has to be LT...

Quote:

---

Originally Posted by Psycho_eddie

Thanks for that... :shakes:


Both UT and LT boards have same layout as i have found out... my question now is as both have same layout...


What other features does the UT offer over the LT? differences?

Also only wanted to clarifiy if UT was even stocked yet... if its not then has to be LT...

---

Correct me if i'm wrong here but the UT has different cooling and a heat pipe and the LT is what most of the members here get since they'll be taking off the extra cooling anyway.

There was an initial batch of LT x48's to motherboardpro.com and i managed to pick one of those up. I'm not sure what the availability is on them now thou.

Quote:

---

Originally Posted by PnoT

Correct me if i'm wrong here but the UT has different cooling and a heat pipe and the LT is what most of the members here get since they'll be taking off the extra cooling anyway.

There was an initial batch of LT x48's to motherboardpro.com and i managed to pick one of those up. I'm not sure what the availability is on them now thou.

---

yup ut got new transpiper
personally i dont think it makes much of a difference unless you running a quad then the transpiper would reduce pwm temp by 5c

How does this DFI X48 card act with 4x1GB Crucial Ballistix DDR1000?
Thanks in advance.

Any confirmation of the tuniq tower fitting? cause ive ordered the board and about to order the cpu and cooling, and would really like to know what fits...

I also want the confirmation with the Thermalright Ultra 120 Extreme after the confirmation with the DDR2 Ram

So I just ordered this board on saturday morning from motherboardspro and ordered a x3350 Xeon from excaliburpc (Q9450 equivalant). They both said they had stock in so Im hoping I will see that they ship tomorrow. Im excited to see how you all will make out with your quad setups on this board. Be sure to post your results.
Thanks

Quote:

---

Originally Posted by CoolZone

How does this DFI X48 card act with 4x1GB Crucial Ballistix DDR1000?
Thanks in advance.

---

it works fine with my team Xtreem PC2-8500 CL5 4x1gb and Team Xtreem PC2-6400 Cl3's 4x1gb..

hmm update dfi FAE is sorting out the asus card issue.. might come out with a bios that has will remove that pcie compatibility option that

I have the board but I'm waiting on my Thermalright U120E. I hope it fits or I'm in trouble =)

Does a table for GTL tweaking exist for 45nm CPUs?...similar to the one linked earlier for 65nm CPUs? I am getting this board this week and don't know anything about how to set the GTL values for my E8400...most people are saying it should be between 60-67 but some people here have it higher and it seems to be working. Also, the GTL settings only work in relation to VTT correct? Meaning the GTL settings should only be adjusted as you adjust VTT.

On the DFI boards, it seems, that if you can get these values down right, your OC becomes much much more stable.

Quote:

---

Originally Posted by Forsaken1

Did not reach goal of sub 10 second superpi 1m tonight.Tomorrow it will fall:).
Thanks for GTL tips:up: .Going to have to put the MCW30 on.

http://i126.photobucket.com/albums/p...tos/5003-1.jpg

---

Forsaken, could you please post your BIOS settings for this OC? Is it prime stable yet? Looking good on Superpi...I'm sure with some sub-timing tweaks, you'll get it under 10 seconds.

I'm really interested in what people are running CPU VTT at and obviously the GTLs alongside it.

This is a little off topic, but I just want to make sure there are no delays when I get my x48!

With vista 64 ultimate will I need a floppy drive to install the raid driver? Are there any other options besides slipstreaming? I really hope they support thumb drives or something this day in age, but if I need a floppy I would ike to know ahead so I can go buy one and have it ready.

Flash drive will work fine with Vista.

Available on Newegg!

http://www.newegg.com/Product/Produc...82E16813136046

Can anyone verify if the thermalright UE 120 will fit