EP45-UD3P

Printable View

Show 100 post(s) from this thread on one page

06-25-2010, 05:19 PM
andressergio

Quote:

Originally Posted by the_real_7

damn sergio thats a super fast p45 board that ddr 3 is running ddr 2 settings amazing fast .... can we see some i7 challenges lol im sure you made the bandwidth up :up:

lol i cant go against integrated mem controllers on I7 but i love this bandw

Thanks Tony :up:
06-25-2010, 05:31 PM
OC Nub

Very nice Sergio.:up:
06-25-2010, 05:39 PM
andressergio

Quote:

Originally Posted by OC Nub

Very nice Sergio.:up:

thanks mate :up:
06-25-2010, 06:35 PM
jjjc_93

Amazing timings Sergio :up:

I was going to have a play with my ram today, but my board is back to not posting. I don't know what it's problem is.
06-25-2010, 06:55 PM
andressergio

Quote:

Originally Posted by jjjc_93

Amazing timings Sergio :up:

I was going to have a play with my ram today, but my board is back to not posting. I don't know what it's problem is.

sorry to hear mate, did u inspect the board as we talked ?
06-25-2010, 07:02 PM
jjjc_93

Quote:

Originally Posted by andressergio

sorry to hear mate, did u inspect the board as we talked ?

Yeah, I can't see any signs of physical damage at all.

It works fine when it does post, but getting it to post is a whole other story.
06-26-2010, 06:11 AM
gugle

hello, someone would have a good setup bios to run day-in day a 501x8.5 Q9550 (4.26ghz)
4 combs of memory usage, memory has been tested in Memtest is OK
watercooler CPU and NB

thanks
06-27-2010, 08:02 AM
bignick

Need some help.

I'm having issues with getting my E6400 above 350FSB? My old ASUS P5K would do 8x400 daily with 1.4V and no increase to NB voltage. I've tried loosening timings on my ram, bumping core and mch voltage and it won't boot if I play with voltages at all. What am I doing wrong? I've been using ASUS boards all my life and because of this thread I chose a Gigabyte for my last 775 board. This bios is very different than what I'm used to looking at and I'm sure thats the problem.
06-27-2010, 09:39 AM
andressergio

Quote:

Originally Posted by gugle

hello, someone would have a good setup bios to run day-in day a 501x8.5 Q9550 (4.26ghz)
4 combs of memory usage, memory has been tested in Memtest is OK
watercooler CPU and NB

thanks

hey mate lots of templates to search in this thread to test and have fun :up:
06-27-2010, 09:45 AM
andressergio

Quote:

Originally Posted by bignick

I'm having issues with getting my E6400 above 350FSB? My old ASUS P5K would do 8x400 daily with 1.4V and no increase to NB voltage. I've tried loosening timings on my ram, bumping core and mch voltage and it won't boot if I play with voltages at all. What am I doing wrong? I've been using ASUS boards all my life and because of this thread I chose a Gigabyte for my last 775 board. This bios is very different than what I'm used to looking at and I'm sure thats the problem.

can you post your settings mate ?
06-29-2010, 05:04 AM
Jsquire

edit: tried some different settings and majorly :banana::banana::banana::banana:ed up, 2 hours later i've had to repair my win7 install.
Okay i'm back up to 4.2Ghz with my E8500 on a EP45-UD3R 443x9.5
the only settings i've changed are as follows
cpu core - 1.4v
LLC - disabled
06-29-2010, 05:08 AM
andressergio

Quote:

Originally Posted by Jsquire

Is there a program that can read bios settings from windows or do i have to manually copy them down?

i dunno if that exists i just take a pic and then make a template...i have them memorized now lol
06-30-2010, 12:24 AM
Jsquire

try again....

Code:

****************************** MB Intelligent Tweaker(M.I.T.) ****************************** Robust Graphics Booster ..............: [Auto] CPU Clock Ratio ......................: [9X] x Fine CPU Clock Ratio................: +0.0 >>>>> Standard Clock Control CPU Host Clock Control................: [Enabled] x CPU Host Frequency(Mhz).............: [467] PCI Express Frequency(Mhz)............: [100] C.I.A.2...............................: [Disabled] >>>>> Advanced Clock Control..........: CPU Clock Drive.......................: [900mV] PCI Express Clock Drive...............: [800mV] CPU Clock Skew........................: [ 0ps] MCH Clock Skew........................: [ 50ps] ******** DRAM Performance Control ******** Performance Enhance...................: [Standard] X.M.P.....[Profile 2] MCH Frequency................: Auto System Memory Multiplier (SPD)........: [2.40B] Memory Frequency(Mhz).................: 1121 DRAM Timing Selectable (SPD)..........: [Auto] >>>>> Standard Timing Control x CAS Latency Time................5...: [ Auto] x tRCD ...........................5...: [ Auto] x tRP.............................5...: [ Auto] x tRAS...........................15...: [Auto] >>>>> Advanced Timing Control.........: [Press Enter] (All Auto here) ****** Motherboard Voltage Control ****** >>> CPU Load-Line Calibration.................: [Enabled] CPU Vcore.....................1.2500V.........: [1.400V] CPU Termination........1.200V.........: [1.280V] CPU PLL................1.500V.........: [1.500V] CPU Reference..........0.760V.........: [0.810] >>> MCH/ICH MCH Core...............1.100V.........: [1.26] MCH Reference..........0.760V.........: [0.810] MCH/DRAM Reference.....0.900V.........: [Normal] ICH I/O................1.500V.........: [Normal] ICH Core...............1.100V.........: [Normal] >>> DRAM DRAM Voltage...........1.800V.........: [2.10V] DRAM Termination.......0.900V.........: [Normal] Channel A Reference....0.900V.........: [Normal] Channel B Reference....0.900V.........: [Normal]

I'm trying to get this E8500 stable at 4.2Ghz, any tips?
06-30-2010, 03:54 AM
andressergio

Quote:

Originally Posted by Jsquire

Code:

****************************** MB Intelligent Tweaker(M.I.T.) ****************************** Robust Graphics Booster ..............: [Auto] CPU Clock Ratio ......................: [9X] x Fine CPU Clock Ratio................: +0.0 >>>>> Standard Clock Control CPU Host Clock Control................: [Enabled] x CPU Host Frequency(Mhz).............: [467] PCI Express Frequency(Mhz)............: [100] C.I.A.2...............................: [Disabled] >>>>> Advanced Clock Control..........: CPU Clock Drive.......................: [900mV] PCI Express Clock Drive...............: [800mV] CPU Clock Skew........................: [ 0ps] MCH Clock Skew........................: [ 50ps] ******** DRAM Performance Control ******** Performance Enhance...................: [Standard] X.M.P.....[Profile 2] MCH Frequency................: Auto System Memory Multiplier (SPD)........: [2.40B] Memory Frequency(Mhz).................: 1121 DRAM Timing Selectable (SPD)..........: [Auto] >>>>> Standard Timing Control x CAS Latency Time................5...: [ Auto] x tRCD ...........................5...: [ Auto] x tRP.............................5...: [ Auto] x tRAS...........................15...: [Auto] >>>>> Advanced Timing Control.........: [Press Enter] (All Auto here) ****** Motherboard Voltage Control ****** >>> CPU Load-Line Calibration.................: [Enabled] CPU Vcore.....................1.2500V.........: [1.400V] CPU Termination........1.200V.........: [1.280V] CPU PLL................1.500V.........: [1.500V] CPU Reference..........0.760V.........: [0.810] >>> MCH/ICH MCH Core...............1.100V.........: [1.26] MCH Reference..........0.760V.........: [0.810] MCH/DRAM Reference.....0.900V.........: [Normal] ICH I/O................1.500V.........: [Normal] ICH Core...............1.100V.........: [Normal] >>> DRAM DRAM Voltage...........1.800V.........: [2.10V] DRAM Termination.......0.900V.........: [Normal] Channel A Reference....0.900V.........: [Normal] Channel B Reference....0.900V.........: [Normal]

I'm trying to get this E8500 stable at 4.2Ghz, any tips?

I never had duals but i would go for

1.3 VTT
1.32+ MCH
dont use XMP, just put disabled

900/900/0/50
07-01-2010, 10:03 AM
Jsquire

After a little tinkering 4.3Ghz stable after 6 hours, thanks for your help andressergio
07-01-2010, 10:31 AM
radaja

Quote:

Originally Posted by Jsquire

I'm trying to get this E8500 stable at 4.2Ghz, any tips?

>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore.....................1.2500V.........: [1.400V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.500V]set to 1.57v
CPU Reference..........0.760V.........: [0.810]set this to normal
>>> MCH/ICH
MCH Core...............1.100V.........: [1.26]set to 1.30v to 1.32v
MCH Reference..........0.760V.........: [0.810]set this to 0.750v
MCH/DRAM Reference.....0.900V.........: [Normal]
ICH I/O................1.500V.........: [Normal]
ICH Core...............1.100V.........: [Normal]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V]
DRAM Termination.......0.900V.........: [Normal]
Channel A Reference....0.900V.........: [Normal]
Channel B Reference....0.900V.........: [Normal]

i have an E8500 on the way and i will post my template for you.this is what worked for my E8400's i had.
07-01-2010, 02:11 PM
bluestang

Quote:

Originally Posted by radaja

>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore.....................1.2500V.........: [1.400V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.500V]set to 1.57v
CPU Reference..........0.760V.........: [0.810]set this to normal
>>> MCH/ICH
MCH Core...............1.100V.........: [1.26]set to 1.30v to 1.32v
MCH Reference..........0.760V.........: [0.810]set this to 0.750v
MCH/DRAM Reference.....0.900V.........: [Normal]
ICH I/O................1.500V.........: [Normal]
ICH Core...............1.100V.........: [Normal]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V]
DRAM Termination.......0.900V.........: [Normal]
Channel A Reference....0.900V.........: [Normal]
Channel B Reference....0.900V.........: [Normal]

i have an E8500 on the way and i will post my template for you.this is what worked for my E8400's i had.

:up: What board you running it in?
07-01-2010, 09:58 PM
radaja

ill be running it my EP45-UD3P with my cellshocks
07-01-2010, 11:43 PM
andressergio

Quote:

Originally Posted by radaja

ill be running it my EP45-UD3P with my cellshocks

can't wait u join as again mate :up:
07-02-2010, 12:58 AM
radaja

thanks andressergio,hopefully i can post some OCs this weekend:D
right now im playing with my i3-530 and ud7.
07-02-2010, 07:58 AM
andressergio

Quote:

Originally Posted by radaja

thanks andressergio,hopefully i can post some OCs this weekend:D
right now im playing with my i3-530 and ud7.

gogo my friend and GoGo Uruguay against Ghana in some hours :D

you can call me by ma name...Sergio

Cheers :toast:
07-02-2010, 07:59 AM
andressergio

Quote:

Originally Posted by Jsquire

After a little tinkering 4.3Ghz stable after 6 hours, thanks for your help andressergio

great to hear that mate :up:
07-02-2010, 08:18 AM
jjjc_93

Just a little update from me:

Board is definitely dead, won't even turn on now. And I was looking at pictures of the board, against my board and found that a capacitor was missing just under the SATAII chip.

I have a little bit of saving to do as I just bought a Single Stage Phase unit, but soon I will have a EP45T USB3P.

Still lots of fun to be had :D
07-02-2010, 09:00 AM
radaja

Quote:

Originally Posted by andressergio

gogo my friend and GoGo Uruguay against Ghana in some hours :D

you can call me by ma name...Sergio

Cheers :toast:

so sergio is your first name?i kept thinking your first name was andres and sergio was your last name:D i learned something new today.:up:
07-02-2010, 10:01 AM
andressergio

Quote:

Originally Posted by radaja

so sergio is your first name?i kept thinking your first name was andres and sergio was your last name:D i learned something new today.:up:

ya im pretty lazy on nicks...my name is Sergio Andrés

Cheers mate :toast:

Show 100 post(s) from this thread on one page

** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P