ASUS Rampage IV Extreme Owners Thread

Printable View

Show 100 post(s) from this thread on one page

02-26-2012, 07:50 PM
OC Nub

[QUOTE=Dumo;5058616]3820 on air

[iQUOTE]

Nice memory clocks!
02-26-2012, 08:21 PM
Dumo

Thanks OC

(2) 3820s same batch 3201B200 with s/n XXA1356 and 1358. One wall @ 5250/2405 mem. cold and second chip (so far) boot up @ 5100/2580 air.

Bios 1103 air....will freez it next.

http://img528.imageshack.us/img528/7...enshot027y.jpg

http://img821.imageshack.us/img821/7...nshot023ud.jpg
02-27-2012, 08:33 AM
Piggin

Can someone please help an n00b
I recently purchased a RIVE, 3930k C2 & 16Gb of mushkin 2133 Mhz

Thanks to donmarkoni information (shown below), I was able to set the board to overclock the chip to 4.5Ghz @ 1.35 volts using BIOS 1101
I tested this with prime 95 without any stability issues.
I then attempted to push the chip further by increasing the cores to 50 & upping the voltage to 1.4v to give me 5.0Ghz
My system would then boot into windows & run without any issues.
Once I run prime 95 the system would lock after a few seconds & give BSOD.
The codes I have noted are
1 - (0xFFFFF880061D7180)
2 - (0xFFFFF880062A5180)
3 - (0xFFFFF880069B3180)

I have steadily increased the voltage to 1.45volts & the system will not run prime95.

The system is being cooled by a custom water setup @ this time. So temps are not that big a problem.
Also is there a list of max voltages that SB-E will run ie. max CPU, VTT, PLL etc as I would prefer not to kill any thing just yet :shakes:

If anyone can point me in the right direction, it will be much appreciated.

Quote:

Originally Posted by donmarkoni

Code:

************************EXTREME TWEAKER************************ =============================================================== LN2 Mode Disable All Core Target CPU Turbo-Mode Speed : 5000MHz Target DRAM Speed : 2400MHz Ai Overclock Tuner [Manual] CPU Level Up [Disabled] BCLK Frequency [100.000] CPU Strap [100MHz] ClockGen Full Reset [Enabled] Turbo Ratio [By All Cores] By All Cores [50] Internal PLL Overvoltage [Enabled] CPU Clock Gen Filter [20UF] Memory Frequency [DDR3-2400MHz] Xtreme Tweaking [Disabled] EPU Power Saving Mode [Disabled] =============================================================== >DRAM Timing Control Rampage Tweak [Mode 2] Primary Timings CHA CHB CHC CHD DRAM CAS# Latency 7 7 7 7 [7] DRAM RAS# to CAS# Delay 11 11 11 11 [11] DRAM RAS# PRE Time 7 7 7 7 [7] DRAM RAS# ACT Time 27 27 27 27 [27] DRAM COMMAND Mode 1 1 1 1 [1] Latency Boundary [Auto] Secondary Timings CHA CHB CHC CHD DRAM RAS# to RAS# Delay 4 4 4 4 [4] DRAM REF Cycle Time 96 96 96 96 [96] DRAM WRITE Recovery Time 14 14 14 14 [14] DRAM READ to PRE Time 4 4 4 4 [4] DRAM FOUR ACT WIN Time 20 20 20 20 [20] DRAM WRITE to READ Dealy 4 4 4 4 [4] DRAM Write Latency 8 8 8 8 [8] Tertiary Timings CHA CHB CHC CHD tRRDR 0 0 0 0 [0] tRRDD 0 0 0 0 [0] tWWDR 0 0 0 0 [0] tWWDD 0 0 0 0 [0] tRWDR 8 8 8 8 [8] tRWDD 3 3 3 3 [3] tWRDR 1 1 1 1 [1] tWRDD 1 1 1 1 [1] tRWSR 8 8 8 8 [8] tCCD 0 0 0 0 [0] Latency Timings CHA CHB CHC CHD DRAM RTL (CHA D0 R0) 37 [Auto] DRAM IOL (CHA D0 R0) 5 [Auto] DRAM RTL (CHA D0 R1) 37 [Auto] DRAM IOL (CHA D0 R1) 5 [Auto] DRAM RTL (CHA D1 R0) 11 [Auto] DRAM IOL (CHA D1 R0) 0 [Auto] DRAM RTL (CHA D1 R1) 11 [Auto] DRAM IOL (CHA D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHB D0 R0) 37 [Auto] DRAM IOL (CHB D0 R0) 7 [Auto] DRAM RTL (CHB D0 R1) 37 [Auto] DRAM IOL (CHB D0 R1) 7 [Auto] DRAM RTL (CHB D1 R0) 11 [Auto] DRAM IOL (CHB D1 R0) 0 [Auto] DRAM RTL (CHB D1 R1) 11 [Auto] DRAM IOL (CHB D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHC D0 R0) 37 [Auto] DRAM IOL (CHC D0 R0) 5 [Auto] DRAM RTL (CHC D0 R1) 37 [Auto] DRAM IOL (CHC D0 R1) 5 [Auto] DRAM RTL (CHC D1 R0) 11 [Auto] DRAM IOL (CHC D1 R0) 0 [Auto] DRAM RTL (CHC D1 R1) 11 [Auto] DRAM IOL (CHC D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHD D0 R0) 37 [Auto] DRAM IOL (CHD D0 R0) 7 [Auto] DRAM RTL (CHD D0 R1) 37 [Auto] DRAM IOL (CHD D0 R1) 7 [Auto] DRAM RTL (CHD D1 R0) 11 [Auto] DRAM IOL (CHD D1 R0) 0 [Auto] DRAM RTL (CHD D1 R1) 11 [Auto] DRAM IOL (CHD D1 R1) 0 [Auto] Others DRAM CLK Period [5] Enhanced Training (CHA) [Disabled] Enhanced Training (CHB) [Disabled] Enhanced Training (CHC) [Disabled] Enhanced Training (CHD) [Disabled] MCH Duty Sense (CHA) [15] MCH Duty Sense (CHB) [17] MCH Duty Sense (CHC) [15] MCH Duty Sense (CHD) [17] Receiver Slew [Normal] Transmitter Slew [Normal] MCH Recheck [Auto] RC Warm Boot Fast [Disabled] =============================================================== >DIGI+ Power Control CPU VCore CPU Load-line Calibration [High] CPU Current Capability [Disabled] CPU Voltage Frequency [Manual] CPU Fixed Frequency [500] VRM Over Temperature Protection [Auto] CPU Power Duty Control [Extreme] Vcore MOS volt. Control [7V] CPU Power Phase Control [Extreme] CPU VCORE Boot Up Voltage [Auto] CPU VSA VCCSA Load-line Calibration [Extreme] VCCSA Current Capability [140%] VCCSA Fixed Frequency [500] CPU VCCSA Boot Up Voltage [Auto] CPU VTT CPU VTT Switching Freq [1.3x] CPU VTT Over-Current Protection [Auto] DRAM Voltage DRAM-AB Current Capability [140%] DRAM-AB Voltage Frequency [Manual] DRAM-AB Fixed Frequency Mode [500] DRAM-AB Power Phase Control [Extreme] DRAM-CD Current Capability [140%] DRAM-CD Voltage Frequency [Manual] DRAM-CD Fixed Frequency Mode [500] DRAM-CD Power Phase Control [Extreme] PCH 1.1V PCH 1.1V Switching Freq [Auto] =============================================================== >CPU Performance Settings CPU Ratio [Auto] Enhanced Intel SpeedStep Technology [Enabled] Turbo Mode [Enabled] -------------------------------------------------------- Turbo Mode Parameters Power Limit Control [Auto] =============================================================== Extreme OV [Disabled] BCLK Skew [Auto] CPU VCORE Voltage 1.432V [Manual Mode] CPU VCORE Manual Voltage [1.430] VTT CPU Voltage 1.218V [1.20000] 2nd VTTCPU Voltage 1.046V [Auto] CPU VCCSA Voltage 1.212V [Manual Mode] CPU VCCSA Manual Voltage [1.200] DRAM Voltage (CHA, CHB) 1.762V [1.770] DRAM Voltage (CHC, CHD) 1.762V [1.775] CPU PLL Voltage 1.884V [Auto] PCH 1.1v Voltage 1.096V [Auto] VTTDDR Voltage (CHA, CHB) [Auto] VTTDDR Voltage (CHC, CHD) [Auto] CPU Spread Spectrum [Disabled] PCIE Spread Spectrum [Disabled] =============================================================== >CPU Tweakers'Paradise PCIE CLK Skew [Auto] CPU I/O Skew [Auto] CPU I/O Drive Strenght [Auto] =============================================================== >Memory Tweakers'Paradise IMC AB Signal 1 [Auto] IMC AB Signal 2 [Auto] IMC AB Signal 3 [Auto] IMC CD Signal 1 [Auto] IMC CD Signal 2 [Auto] IMC cD Signal 3 [Auto] DRAM CTRL REF Voltage on CHA [Auto] DRAM DATA REF Voltage on CHA [Auto] DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHB [Auto] DRAM CTRL REF Voltage on CHC [Auto] DRAM DATA REF Voltage on CHC [Auto] DRAM CTRL REF Voltage on CHD [Auto] DRAM DATA REF Voltage on CHD [Auto] DRAM Read REF Voltage on CHA [Auto] DRAM Read REF Voltage on CHB [Auto] DRAM Read REF Voltage on CHC [Auto] DRAM Read REF Voltage on CHD [Auto] =============================================================== >PCH Chipset Tweakers'Paradise PCH 1.5V Voltage 1.503V [Auto] PCH 1.1VG [Auto] PCH DMI Strenght [Auto] PCH DMI Skew [Auto] PCH USB Skew [Auto] PCH SATA3 Strenght [Auto] =============================================================== >VGA Tweakers'Paradise VGA1 Core Voltage [Auto] VGA1 Core Voltage Boost [Disabled] VGA1 Memory Voltage [Auto] VGA1 PLL Voltage [Auto] VGA2 Core Voltage [Auto] VGA2 Core Voltage Boost [Disabled] VGA2 Memory Voltage [Auto] VGA2 PLL Voltage [Auto] =============================================================== ***************************ADVANCED**************************** =============================================================== CPU Configuration Intel Adaptive Thermal Monitor [Enabled] Hyper-threading [Enabled] Active Processor Cores [All] Limit CPUID Maximum [Disabled] Execute Disable Bit [Enabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetcher [Enabled] Intel Virtualization Technology [Enabled] >CPU Power Management Configuration CPU Ratio [Auto] Enhanced Intel SpeedStep Technology [Enabled] Turbo Mode [Enabled] CPU C1E [Enabled] CPU C3 Report [Enabled] CPU C6 Report [Enabled] CPU C7 Report [Enabled] =============================================================== System Agent Configuration Inter(R) VT-d [Disabled] PCIE_X16_1 Link Speed [GEN3] PCIE_X16/X8_3 and PCIE_X8_4 Link Speed [GEN3] PCIE_X8_2A and PCIE_X8_2B Link Speed [GEN3] =============================================================== PCH Configuration High Precision Timer [Disabled] ===============================================================
02-27-2012, 08:37 AM
Kensek

Those settings are trying to run your DRAM @ 2400 with CL 7 timings. That will not work.

Also most CPUs to run 6c/12t at 5.0GHz take 1.48 - 1.52v
02-27-2012, 08:49 AM
Piggin

Thanks Kensek for the reply.
I should have added that I set the ram to the correct specification set out by muskin.
Am I better off underclocking the RAM for now until I can find the upper limit of the chip?
02-27-2012, 09:01 AM
Eldonko

Yeah for SB-E it is a good idea to clock CPU, BCLK, and mem separately at first so you have an idea where each maxes out. Makes it easier in the long run.
02-27-2012, 09:38 AM
Piggin

Thanks Eldonko
Just had another go @ 5.0Ghz with the RAM set @ 1600Mhz & then 1066Mhz & I am still getting the message "clock interrupt was not received on a second processor within the allocated time intended"
02-27-2012, 09:51 AM
Eldonko

What are your temps like? Keep in mind not all chips are going to do 5Ghz..
02-27-2012, 10:49 AM
Piggin

The temps are around 60C
I understand that not all chips are the same (silicon lottery) but I would like to try & get as much from it as possible.
02-27-2012, 11:57 AM
donmarkoni

Have you tried 125x40? There is widespread opinion, backed by theory, that lower multi requires less voltage for SB-E.
02-27-2012, 03:45 PM
Piggin

Thanks donmarkoni for the input.
I did what you suggested & used 125x40 with 1.5 volts - BSOD
Then 125x39 with 1.5 volts - BSOD
Then 125X38 with 1.45 volts & its still running prime
02-27-2012, 10:07 PM
Dumo

2632

http://img404.imageshack.us/img404/3...enshot038e.jpg

http://img214.imageshack.us/img214/4...nshot043cu.jpg
02-27-2012, 11:08 PM
owikh84

@ great IMC Dumo :up:
02-27-2012, 11:25 PM
Dumo

Thanks owik:)

My third 3820 turned out to be good @ least on air, hope it will scale higher with cold
02-28-2012, 12:20 AM
l0ud_sil3nc3

looks like you got a good one Dumo:yepp:

If they can clock memory well, they tend to clock high on the core as well (at least on sb-e), I am sure it will be nice on cold, especially since your already at almost 5100:up:
02-28-2012, 05:18 AM
Piggin

Quote:

Originally Posted by Piggin

Thanks donmarkoni for the input.
I did what you suggested & used 125x40 with 1.5 volts - BSOD
Then 125x39 with 1.5 volts - BSOD
Then 125X38 with 1.45 volts & its still running prime

I have continued testing & I run prime 95 for 8 hrs with 125x38 @1.42 volts (memory set @ 2000Mhz)
The other settings were
VTT CPU - 1.2v
2nd VTTCPU - 1.05v
CPU VCCSA - 1.221v
DRAM - 1.668v
CPU PLL - 1.881v
PCH - 1.096v

Is there something I am missing or can I push any of the other settings a little harder due to being under water (have increased CPU voltage up to 1.5v & still getting 0101 codes)
Any help will be gratefully received
02-28-2012, 06:44 AM
Viss

Very nice chip Dumo :up:
02-28-2012, 01:02 PM
donmarkoni

Quote:

Originally Posted by Piggin

I have continued testing & I run prime 95 for 8 hrs with 125x38 @1.42 volts (memory set @ 2000Mhz)
The other settings were
VTT CPU - 1.2v
2nd VTTCPU - 1.05v
CPU VCCSA - 1.221v
DRAM - 1.668v
CPU PLL - 1.881v
PCH - 1.096v

Is there something I am missing or can I push any of the other settings a little harder due to being under water (have increased CPU voltage up to 1.5v & still getting 0101 codes)
Any help will be gratefully received

Those are nice 24/7 settings, if nothing better is gained.
You can try 100x48 with same or slightly higher voltage to see if there is effect from higher/lower multi.
Also try playing with CPU PLL (1.25V- 2.00V), and BCLK Skew/PCIE CLK Skew -1/-10, -2/-20, +1/+5, +1/+10, +2/+10.
Could be that CPU is not such a great one.
02-28-2012, 01:12 PM
Dumo

Quote:

Originally Posted by l0ud_sil3nc3

looks like you got a good one Dumo:yepp:

Thanks l0ud:up:...Still wanna play with it before go cold

Quote:

Originally Posted by Viss

Very nice chip Dumo :up:

Thanks Viss, not too shabby for my third 3820 binned:D

166 strap...

http://img818.imageshack.us/img818/4...enshot047q.jpg

Max bclk on air...

http://img835.imageshack.us/img835/9...enshot048i.jpg
02-28-2012, 04:23 PM
OC Nub

Nice Dumo! 162bclk and 2300c10 is pretty strong, cant wait to see you results on SS.
02-28-2012, 04:34 PM
andressergio

Quote:

Originally Posted by Dumo

Thanks l0ud:up:...Still wanna play with it before go cold

Thanks Viss, not too shabby for my third 3820 binned:D

166 strap...

http://img818.imageshack.us/img818/4...enshot047q.jpg

Holly Molly !!! grats Dumo
02-29-2012, 12:08 AM
l0ud_sil3nc3

Quote:

Originally Posted by OC Nub

Nice Dumo! 162bclk and 2300c10 is pretty strong, cant wait to see you results on SS.

2600c10 is what I think you meant;)
02-29-2012, 01:33 AM
LardArse

Quote:

Originally Posted by Piggin

I have continued testing & I run prime 95 for 8 hrs with 125x38 @1.42 volts (memory set @ 2000Mhz)
The other settings were
VTT CPU - 1.2v
2nd VTTCPU - 1.05v
CPU VCCSA - 1.221v
DRAM - 1.668v
CPU PLL - 1.881v
PCH - 1.096v

Is there something I am missing or can I push any of the other settings a little harder due to being under water (have increased CPU voltage up to 1.5v & still getting 0101 codes)
Any help will be gratefully received

you may wanna use this to balance temps with speeds
http://rog.asus.com/forum/showthread...ight=maximiser
02-29-2012, 07:07 AM
Piggin

Quote:

Originally Posted by donmarkoni

Those are nice 24/7 settings, if nothing better is gained.
You can try 100x48 with same or slightly higher voltage to see if there is effect from higher/lower multi.
Also try playing with CPU PLL (1.25V- 2.00V), and BCLK Skew/PCIE CLK Skew -1/-10, -2/-20, +1/+5, +1/+10, +2/+10.
Could be that CPU is not such a great one.

Thank you very much for you input.
I will give it a go when I get home latter.

Quote:

Originally Posted by LardArse

you may wanna use this to balance temps with speeds
http://rog.asus.com/forum/showthread...ight=maximiser

Thank you. Will down load this later & give it a go.
02-29-2012, 04:52 PM
OC Nub

Quote:

Originally Posted by l0ud_sil3nc3

2600c10 is what I think you meant;)

Yes, oops.

Show 100 post(s) from this thread on one page

***ASUS Rampage IV Extreme Owners Thread***

ASUS Rampage IV Extreme Owners Thread