** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Quote:

Originally Posted by andressergio

jeeeze man how come what PSU u where using :confused:

A rebadged 1000w Xilence PSU. Yeah I was asking for everything I got, but funds were tight and this psu got the job done for nearly 2 years.
Will be looking at getting an 850 or 1000HX this time round.

Quote:

Originally Posted by In-Fluence

Nice loop Noguru. Is the Rad an XSPC?

Yes it the XSPC RX360

Quote:

Originally Posted by MrDucky

now we want to know the temps noguru :D

Blend stays around 55c I forgot to check the NB at load, but it idles at 42c and the
5850 stays at 41c in Furmark:eek: that is amazing to me.

Quote:

Originally Posted by jjjc_93

Finally booted into windows at 4.6Ghz and the psu blew. Damn murpy's law:rofl:
Going to see if I can get a decently priced replacement tomorrow, and get back to the overclocking.

I also want to know your temps noguru:D

What PSU where you using? Odd to have them blow from an overclock.
Opps, just seen your post.

Quote:

Originally Posted by jjjc_93

A rebadged 1000w Xilence PSU. Yeah I was asking for everything I got, but funds were tight and this psu got the job done for nearly 2 years.
Will be looking at getting an 850 or 1000HX this time round.

get the HX850 hella PSU :up:

NoGuru,very nice WCing build.looks like andressergios and yours and mine are family.
all gigabyte,all blue and all look great.

Quote:

Originally Posted by radaja

NoGuru,very nice WCing build.looks like andressergios and yours and mine are family.
all gigabyte,all blue and all look great.

Thanks radaja!:) Sergio helped me build the whole thing except the blocks, I bought them used about a month ago.
Might have to do some blue LED's too.

Agreed, HX850 (or 1000 if you've got the room). I've heard the 850 can manage up to 1000 anyway so probably a little more bang for your bucks ;)

@NoGuru - nice - the XSPC rads are probably the only worthy competitor to the thermochills from what I've read, and the big fins are great if you're after a quieter setup, plus the price is reasonable. I think my XSPC pump is probably suffering a little now though, so I'm thinking of going for a dual loop reservoir and a single laing pump next. After that I may build on a bit more GFX cooling and mosfets when my USB3P arrives. I think I've fathomed a way to fit it all in and around the case and can probably make room for another 240 rad at least, but it's so heavy already I probably won't be able to lift it with yet more addons & water!

I need help getting my E8500 to 4.275ghz, my EP45-UD3R is using the F12 BIOS

Code:

MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto CPU Clock Ratio .......................: 9 Fine CPU Clock Ratio...................:.0.5 CPU Frequency .........................: 4.275GHz (450*9.5) Clock Chip Control Standard Clock Control CPU Host Clock Control.................: [Enabled] CPU Host Frequency (Mhz) ..............: 450 PCI Express Frequency (Mhz) ...........: 100 C.I.A.2 .................................:[Disabled] CPU Clock Drive........................: 800 PCI Express Clock Drive................: 900 CPU Clock Skew (ps)....................: 50 MCH Clock Skew (ps)....................: 0 DRAM Performance Control Performance Enhance....................: [Extreme] Extreme Memory Profile (X.M.P.)........: Profile 2 (G)MCH Frequency Latch.................: AUTO System Memory Multiplier ..............: 2.00D Memory Frequency (Mhz) ................: 900 DRAM Timing Selectable ................: [Auto] Motherboard Voltage Control Voltage Type.………... Manual LLC....................................: [Enabled] CPU Vcore….……….........................: 1.38125v CPU Termination….......................: 1.28v CPU PLL………………….........................: 1.5v CPU Referen.………….......................: 0.795v MCH/ICH MCH Core…………….....1.100V...............: 1.36v MCH Reference….…….0.800V...............: 0.790 MCH/DRAM Ref.…......0.900V.............: Normal ICH I/O……………….....1.500V...............: Normal ICH Core…………...……1.100V................: Normal DRAM DRAM Voltage ……....1.800V..............: 2.000V DRAM Termination .…0.900V..............: Normal Channel A Reference 0.900V.............: Normal Channel B Reference 0.900V.............: Normal

i can run prime95 for about 10 minuets until one core stops, and the highest CPU core temp is 63c

Quote:

Originally Posted by dustin_ds3000

I need help getting my E8500 to 4.275ghz, my EP45-UD3R is using the F12 BIOS

Code:

MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto CPU Clock Ratio .......................: 9 Fine CPU Clock Ratio...................:.0.5 CPU Frequency .........................: 4.275GHz (450*9.5) Clock Chip Control Standard Clock Control CPU Host Clock Control.................: [Enabled] CPU Host Frequency (Mhz) ..............: 450 PCI Express Frequency (Mhz) ...........: 100 C.I.A.2 .................................:[Disabled] CPU Clock Drive........................: 800 PCI Express Clock Drive................: 900 CPU Clock Skew (ps)....................: 50 MCH Clock Skew (ps)....................: 0 DRAM Performance Control Performance Enhance....................: [Extreme] Extreme Memory Profile (X.M.P.)........: Profile 2 (G)MCH Frequency Latch.................: AUTO System Memory Multiplier ..............: 2.00D Memory Frequency (Mhz) ................: 900 DRAM Timing Selectable ................: [Auto] Motherboard Voltage Control Voltage Type.………... Manual LLC....................................: [Enabled] CPU Vcore….……….........................: 1.38125v CPU Termination….......................: 1.28v CPU PLL………………….........................: 1.5v CPU Referen.………….......................: 0.795v MCH/ICH MCH Core…………….....1.100V...............: 1.36v MCH Reference….…….0.800V...............: 0.790 MCH/DRAM Ref.…......0.900V.............: Normal ICH I/O……………….....1.500V...............: Normal ICH Core…………...……1.100V................: Normal DRAM DRAM Voltage ……....1.800V..............: 2.000V DRAM Termination .…0.900V..............: Normal Channel A Reference 0.900V.............: Normal Channel B Reference 0.900V.............: Normal

i can run prime95 for about 10 minuets until one core stops, and the highest CPU core temp is 63c

put turbo not extreme and profile1 mate

900/900/0/50

PCIE= 101

for 1,2vtt set .785CPU ref and .80MCH then up vtt to ya current value ;)
try

Cheers :up:
Sergio

Quote:

Originally Posted by andressergio

put turbo not extreme and profile1 mate

900/900/0/50

PCIE= 101

for 1,2vtt set .785CPU ref and .80MCH then up vtt to ya current value ;)
try

Cheers :up:
Sergio

in the BIOS for Extreme Memory Profile i have Auto, profile2, and disable. No profile1 unless disable is profile1

*10 minutes later*

Those BIOS settings give the the blue screen after windows starts to load

*10 minutes later*

i changed the MCH ref to .760 and i booted into windows and im running prime95 now

Quote:

Originally Posted by radaja

NoGuru,very nice WCing build.looks like andressergios and yours and mine are family.
all gigabyte,all blue and all look great.

a giga family :rofl:

Cheers Rob :up:
Sergio

well pime95 failed after a few minutes so i started to try other settings, after getting blue screen after blue screen i just went back to my 9.5x422 4Ghz settings.

Quote:

Originally Posted by dustin_ds3000

well pime95 failed after a few minutes so i started to try other settings, after getting blue screen after blue screen i just went back to my 9.5x422 4Ghz settings.

did u use my settings mate ?

remember that you have to set .785 CPU REF and .80 MCH and put VTT 1.2 then up just VTT to the value you want letting other change alone

you have to try skews

800/800/0/50
900/900/0/50
800/900/50/100

seek wich fits best for ya

MCH on 1,4 if you are pushing

vdimm a bit overvolted

and NO extreme , just use STANDARD to try then you have time to put TURBO

try CUSTOM BLEND 8k to 8k at first if it passes that
go blend all. if fails...notch vcore

Cheers hope it helps :up:

2 Attachment(s)

Fan controller is installed.:D

Quote:

Originally Posted by dustin_ds3000

I need help getting my E8500 to 4.275ghz, my EP45-UD3R is using the F12 BIOS

i can run prime95 for about 10 minuets until one core stops, and the highest CPU core temp is 63c

Give this a try.

Code:

MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto CPU Clock Ratio .......................: 9 Fine CPU Clock Ratio...................:.0.5 CPU Frequency .........................: 4.275GHz (450*9.5) Clock Chip Control Standard Clock Control CPU Host Clock Control.................: [Enabled] CPU Host Frequency (Mhz) ..............: 450 PCI Express Frequency (Mhz) ...........: 100 C.I.A.2 .................................:[Disabled] CPU Clock Drive........................: 800 PCI Express Clock Drive................: 900 CPU Clock Skew (ps)....................: 0 MCH Clock Skew (ps)....................: 0 DRAM Performance Control Performance Enhance....................: Standard Extreme Memory Profile (X.M.P.)........: disabled (G)MCH Frequency Latch.................: 400 System Memory Multiplier ..............: 2.00D Memory Frequency (Mhz) ................: 900 DRAM Timing Selectable ................: [Auto] Motherboard Voltage Control Voltage Type.………... Manual LLC....................................: [Enabled] CPU Vcore….……….........................: 1.38125v CPU Termination….......................: 1.26v CPU PLL………………….........................: 1.50v CPU Referen.………….......................: 0.798v MCH/ICH MCH Core…………….....1.100V...............: 1.32v MCH Reference….…….0.800V...............: 0.718 - 0.758 MCH/DRAM Ref.…......0.900V.............: Auto ICH I/O……………….....1.500V...............: 1.500 ICH Core…………...……1.100V................: 1.100 DRAM DRAM Voltage ……....1.800V..............: 2.000V DRAM Termination .…0.900V..............: Auto Channel A Reference 0.900V.............: Auto Channel B Reference 0.900V.............: Auto

Quote:

Originally Posted by NoGuru

Fan controller is installed.:D

Looking good :up:

Hi Hoss, great stuff with the uD3P,

I would love to see your template for the Q9650

in the high 4.8+ ghz to 5ghz/////

any chance of that? :shrug:

best regards/steve

Quote:

Originally Posted by Hoss331

Give this a try.

Code:

MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto CPU Clock Ratio .......................: 9 Fine CPU Clock Ratio...................:.0.5 CPU Frequency .........................: 4.275GHz (450*9.5) Clock Chip Control Standard Clock Control CPU Host Clock Control.................: [Enabled] CPU Host Frequency (Mhz) ..............: 450 PCI Express Frequency (Mhz) ...........: 100 C.I.A.2 .................................:[Disabled] CPU Clock Drive........................: 800 PCI Express Clock Drive................: 900 CPU Clock Skew (ps)....................: 0 MCH Clock Skew (ps)....................: 0 DRAM Performance Control Performance Enhance....................: Standard Extreme Memory Profile (X.M.P.)........: disabled (G)MCH Frequency Latch.................: 400 System Memory Multiplier ..............: 2.00D Memory Frequency (Mhz) ................: 900 DRAM Timing Selectable ................: [Auto] Motherboard Voltage Control Voltage Type.………... Manual LLC....................................: [Enabled] CPU Vcore….……….........................: 1.38125v CPU Termination….......................: 1.26v CPU PLL………………….........................: 1.50v CPU Referen.………….......................: 0.798v MCH/ICH MCH Core…………….....1.100V...............: 1.32v MCH Reference….…….0.800V...............: 0.718 - 0.758 MCH/DRAM Ref.…......0.900V.............: Auto ICH I/O……………….....1.500V...............: 1.500 ICH Core…………...……1.100V................: 1.100 DRAM DRAM Voltage ……....1.800V..............: 2.000V DRAM Termination .…0.900V..............: Auto Channel A Reference 0.900V.............: Auto Channel B Reference 0.900V.............: Auto

Looking good :up:

this is very frustrating o/c in hot summer days is a pita. Just got a new USB3P and man the idle temp for my q6600 is 58-60'C. Even with a/c on is like 53-55'C. Seeing how you guys clock above 3.8ghz is crazy.

Quote:

Originally Posted by NeoGeo333

this is very frustrating o/c in hot summer days is a pita. Just got a new USB3P and man the idle temp for my q6600 is 58-60'C. Even with a/c on is like 53-55'C. Seeing how you guys clock above 3.8ghz is crazy.

That can't be right, idle 60C :eek:
Remount you cooler. Make sure the fan is working.

Quote:

Originally Posted by systemviper

Hi Hoss, great stuff with the uD3P,

I would love to see your template for the Q9650

in the high 4.8+ ghz to 5ghz/////

any chance of that? :shrug:

best regards/steve

Thanks, Im not good at keeping track of old settings but this should be pretty close for the 5.0 spi 1m and 4.95 wprime 1024 water runs.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio.................................[ 9 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 4.95GHz...........................[ 550 x 9.0] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 550 ] PCI Express Frequency (Mhz).....................[ 101 ] C.I.A 2.........................................[ Disabled ] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv ] PCI Express Clock Drive.........................[ 1000mv ] CPU Clock Skew..................................[ 100ps ] MCH Clock Skew..................................[ 50ps ] ******DRAM Performance Control****** Performance Enhance.............................[ Standard ] (G) MCH Frequency Latch.........................[ 400 ] System Memory Multipler.........................[ 2.00D ] Memory Frequency 1066...........................[ 1100 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 4 ] tRCD............................................[ 4 ] tRP.............................................[ 4 ] tRAS............................................[ 10 ] ******Advanced Timing Control****** tRRD[3].........................................[ 3 ] tWTR[3].........................................[ 3 ] tWR[6]..........................................[ 6 ] tRFC[54]........................................[ 34 ] tRTP[3].........................................[ 3 ] Command Rate (cmd)[0]...........................[ Auto ] ******Channel A Timing Settings****** Static tRead Value [ 8 ].................[ 8 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 8 ].................[ 8 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ 1.15 ].....................[ 1.600 ] CPU Termination [ 1.20 ].....................[ 1.520 ] CPU PLL [ 1.50 ].....................[ 1.670 ] CPU Reference [ 0.760 ].....................[ 1.003 ] MCH Core [ 1.100 ].....................[ 1.560 ] MCH Reference [ 0.760 ].....................[ 0.963 ] MCH/DRAM Refernce [ 0.900 ].....................[ 1.230 ] ICH I/O [ 1.500 ].....................[ 1.500 ] ICH Core [ 1.100 ].....................[ 1.100 ] DRAM Voltage [ 1.800 ].....................[ 2.460 ] DRAM Termination [ 0.900 ].....................[ 1.230 ] Channel A Ref [ 0.900 ].....................[ 1.230 ] Channel B Ref [ 0.900 ].....................[ 1.230 ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]

These are my current boot settings for 5.1+ and so far are good for spi 1m up to 5.13(570).

Code:

******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio.................................[ 9 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 5.1GHz............................[ 567 x 9.0] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 567 ] PCI Express Frequency (Mhz).....................[ 101 ] C.I.A 2.........................................[ Disabled ] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv ] PCI Express Clock Drive.........................[ 1000mv ] CPU Clock Skew..................................[ 100ps ] MCH Clock Skew..................................[ 100ps ] ******DRAM Performance Control****** Performance Enhance.............................[ Standard ] (G) MCH Frequency Latch.........................[ 333 ] System Memory Multipler.........................[ 2.00B ] Memory Frequency 1066...........................[ 1134 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 4 ] tRCD............................................[ 4 ] tRP.............................................[ 4 ] tRAS............................................[ 8 ] ******Advanced Timing Control****** tRRD[3].........................................[ 4 ] tWTR[3].........................................[ 4 ] tWR[6]..........................................[ 8 ] tRFC[54]........................................[ 26 ] tRTP[3].........................................[ 4 ] Command Rate (cmd)[0]...........................[ Auto ] ******Channel A Timing Settings****** Static tRead Value [ 8 ].................[ 9 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 8 ].................[ 9 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ 1.15 ].....................[ 1.640 ] CPU Termination [ 1.20 ].....................[ 1.600 ] CPU PLL [ 1.50 ].....................[ 1.710 ] CPU Reference [ 0.760 ].....................[ 1.038 ] MCH Core [ 1.100 ].....................[ 1.600 ] MCH Reference [ 0.760 ].....................[ 1.013 ] MCH/DRAM Refernce [ 0.900 ].....................[ 1.270 ] ICH I/O [ 1.500 ].....................[ 1.570 ] ICH Core [ 1.100 ].....................[ 1.200 ] DRAM Voltage [ 1.800 ].....................[ 2.540 ] DRAM Termination [ 0.900 ].....................[ 1.270 ] Channel A Ref [ 0.900 ].....................[ 1.270 ] Channel B Ref [ 0.900 ].....................[ 1.270 ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]

Quote:

Originally Posted by NoGuru

That can't be right, idle 60C :eek:
Remount you cooler. Make sure the fan is working.

opened the case and notice way too many micro bubbles in the loop. anyone with advice to take care of that?

Quote:

Originally Posted by NeoGeo333

opened the case and notice way too many micro bubbles in the loop. anyone with advice to take care of that?

To get the bubbles out you need to shake the case a bit and open the res and bleed them.
I don't think the is your problem though. I would remount the cooler.

Thanks mucho Hoss, i was very interested in the skews and a few subtle settings.

I'll give them a shot tomorrow. :up:

best regards/steve

Quote:

Originally Posted by Hoss331

Thanks, Im not good at keeping track of old settings but this should be pretty close for the 5.0 spi 1m and 4.95 wprime 1024 water runs.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio...............................[ 9 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 4.95GHz...........................[ 550 x 9.0] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 550 ] PCI Express Frequency (Mhz).....................[ 101 ] C.I.A 2.........................................[ Disabled ] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv ] PCI Express Clock Drive.........................[ 1000mv ] CPU Clock Skew..................................[ 100ps ] MCH Clock Skew..................................[ 50ps ] ******DRAM Performance Control****** Performance Enhance.............................[ Standard ] (G) MCH Frequency Latch.........................[ 400 ] System Memory Multipler.........................[ 2.00D ] Memory Frequency 1066...........................[ 1100 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 4 ] tRCD............................................[ 4 ] tRP.............................................[ 4 ] tRAS............................................[ 10 ] ******Advanced Timing Control****** tRRD[3].........................................[ 3 ] tWTR[3].........................................[ 3 ] tWR[6]..........................................[ 6 ] tRFC[54]........................................[ 34 ] tRTP[3].........................................[ 3 ] Command Rate (cmd)[0]...........................[ Auto ] ******Channel A Timing Settings****** Static tRead Value [ 8 ].................[ 8 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 8 ].................[ 8 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ 1.15 ].....................[ 1.600 ] CPU Termination [ 1.20 ].....................[ 1.520 ] CPU PLL [ 1.50 ].....................[ 1.670 ] CPU Reference [ 0.760 ].....................[ 1.003 ] MCH Core [ 1.100 ].....................[ 1.560 ] MCH Reference [ 0.760 ].....................[ 0.963 ] MCH/DRAM Refernce [ 0.900 ].....................[ 1.230 ] ICH I/O [ 1.500 ].....................[ 1.500 ] ICH Core [ 1.100 ].....................[ 1.100 ] DRAM Voltage [ 1.800 ].....................[ 2.460 ] DRAM Termination [ 0.900 ].....................[ 1.230 ] Channel A Ref [ 0.900 ].....................[ 1.230 ] Channel B Ref [ 0.900 ].....................[ 1.230 ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]

These are my current boot settings for 5.1+ and so far are good for spi 1m up to 5.13(570).

Code:

******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio.................................[ 9 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 5.1GHz............................[ 567 x 9.0] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 567 ] PCI Express Frequency (Mhz).....................[ 101 ] C.I.A 2.........................................[ Disabled ] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv ] PCI Express Clock Drive.........................[ 1000mv ] CPU Clock Skew..................................[ 100ps ] MCH Clock Skew..................................[ 100ps ] ******DRAM Performance Control****** Performance Enhance.............................[ Standard ] (G) MCH Frequency Latch.........................[ 333 ] System Memory Multipler.........................[ 2.00B ] Memory Frequency 1066...........................[ 1134 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 4 ] tRCD............................................[ 4 ] tRP.............................................[ 4 ] tRAS............................................[ 8 ] ******Advanced Timing Control****** tRRD[3].........................................[ 4 ] tWTR[3].........................................[ 4 ] tWR[6]..........................................[ 8 ] tRFC[54]........................................[ 26 ] tRTP[3].........................................[ 4 ] Command Rate (cmd)[0]...........................[ Auto ] ******Channel A Timing Settings****** Static tRead Value [ 8 ].................[ 9 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 8 ].................[ 9 ] tRD Phase0 Adjustment [ 0 ].................[ Auto ] tRD Phase1 Adjustment [ 0 ].................[ Auto ] tRD Phase2 Adjustment [ 0 ].................[ Auto ] tRD Phase3 Adjustment [ 0 ].................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ].................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ].................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ].................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ 1.15 ].....................[ 1.640 ] CPU Termination [ 1.20 ].....................[ 1.600 ] CPU PLL [ 1.50 ].....................[ 1.710 ] CPU Reference [ 0.760 ].....................[ 1.038 ] MCH Core [ 1.100 ].....................[ 1.600 ] MCH Reference [ 0.760 ].....................[ 1.013 ] MCH/DRAM Refernce [ 0.900 ].....................[ 1.270 ] ICH I/O [ 1.500 ].....................[ 1.570 ] ICH Core [ 1.100 ].....................[ 1.200 ] DRAM Voltage [ 1.800 ].....................[ 2.540 ] DRAM Termination [ 0.900 ].....................[ 1.270 ] Channel A Ref [ 0.900 ].....................[ 1.270 ] Channel B Ref [ 0.900 ].....................[ 1.270 ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]

Quote:

Originally Posted by NoGuru

To get the bubbles out you need to shake the case a bit and open the res and bleed them.
I don't think the is your problem though. I would remount the cooler.

bleed the bubbles out by slowing the pump down a few minutes and opening the res. that took care of the bubbles, remounted cpu block and now idle at 45'C, still think is high for a Q6600 at 3.6ghz at 1.38v?

A lot better but still a little high for those volts. Is your CPU/cooler surface flat? If you remove the block, is the paste unevenly spread?

Quote:

Originally Posted by In-Fluence

A lot better but still a little high for those volts. Is your CPU/cooler surface flat? If you remove the block, is the paste unevenly spread?

I agree.

What CPU block do you have, or the whole loop for that matter?
What method of applying TIM do you use?

Quote:

Originally Posted by NoGuru

I agree.

What CPU block do you have, or the whole loop for that matter?
What method of applying TIM do you use?

Im using MX-3 and theres no formal way to apply other than a drop of it in the middle and thats it. Using a XSPC Rasa CPU Acetal block, dont know if its good for Q6600, or should have stock with Swiftech Apogee.