[First Look] Retail Box DFI UT LP P-35-T2R (56K Warning~~)

Printable View

Show 100 post(s) from this thread on one page

08-04-2007, 08:32 AM
cyberspyder

Andre, what its the length of the heatsink covering the digital PWM?

http://img120.imageshack.us/img120/143/16zc5.jpg

Also, where are the MOSFETs on this board?

Thanks, Brendan
08-04-2007, 09:21 AM
Apeman69

Hey...Check this out

http://www.tweaktown.com/news/7879/index.html
08-04-2007, 09:37 AM
TEDY

apeman 69 lower you sig.
08-04-2007, 09:39 AM
vudoodoodoo

lol @ apeman
08-04-2007, 09:50 AM
TinTin

Quote:

Originally Posted by cyberspyder

Andre, what its the length of the heatsink covering the digital PWM?

http://img120.imageshack.us/img120/143/16zc5.jpg

Also, where are the MOSFETs on this board?

Thanks, Brendan

7cm :D

under the heatsink
08-04-2007, 10:38 AM
Capt_Caveman

Quote:

Originally Posted by Tibu

Man... I'm a huge DFI fan. Especially of their LP boards. But if X38 isn't that far away... oh man I just don't know.

I agree. I wish DFI could come out with their boards sooner.
08-04-2007, 10:48 AM
MacClipper

Quote:

Originally Posted by TinTin

7cm :D

under the heatsink

Is it out in HK already huh?
08-04-2007, 11:06 AM
cyberspyder

Quote:

Originally Posted by TinTin

7cm :D

under the heatsink

Thanks, what pisses me off is that I need to buy the 'TYPE2' Thermalirght HR-09, but everyone's just stocking the regular 'TYPE1'

Brendan
08-04-2007, 11:23 AM
palese

I refuse to get caught up in the DFI hype machine again after the disappointing 680i board. No more I gotta have it first:ROTF:
08-04-2007, 11:26 AM
jkresh

cyberspyder, I thought it was the type 3 thermalright for the dfi boards? Yet i have not seen any place with anything but the type 1.
08-04-2007, 12:03 PM
cyberspyder

Quote:

Originally Posted by jkresh

cyberspyder, I thought it was the type 3 thermalright for the dfi boards? Yet i have not seen any place with anything but the type 1.

I was planning on using the HR-09 for digital PWM cooling, not MOSFET, and the only one long enough for that is the TYPE2
08-04-2007, 04:32 PM
Chosen.

Quote:

Originally Posted by AndreYang

This motherboard will be available in few days.

08-01-2007, 02:54 PM
lol :rolleyes:
I say in about 1 month :/
08-04-2007, 06:02 PM
NKD

i think the board looks sexy, and its worth the price, but i hate dfi for coming late all the time, i used to be impressed before, but i cant really wait 2-3 months and ignore the abit and asus baords, its just not worth the wait, and please dont give me that "we were tweaking the bios" stuff. everyone tweaks thier bios and my abit boad is kicking at 2000FSB right now and its on the first release bios.
08-04-2007, 06:42 PM
mucker

Quote:

Originally Posted by NKD

i think the board looks sexy, and its worth the price, but i hate dfi for coming late all the time, i used to be impressed before, but i cant really wait 2-3 months and ignore the abit and asus baords, its just not worth the wait, and please dont give me that "we were tweaking the bios" stuff. everyone tweaks thier bios and my abit boad is kicking at 2000FSB right now and its on the first release bios.

I can't help but agree with that, even though I liked and used the "late to market" 965S and the Ultra-D, that were much more attractive from a price standpoint........
08-04-2007, 06:43 PM
TinTin

Quote:

Originally Posted by MacClipper

Is it out in HK already huh?

yes, it is out in HK, but only 10pcs came to HK and all sold in one day.:)
08-04-2007, 06:54 PM
erwinz

Quote:

Originally Posted by TinTin

yes, it is out in HK, but only 10pcs came to HK and all sold in one day.:)

do you have one.. :D
08-04-2007, 07:12 PM
TinTin

Quote:

Originally Posted by erwinz

do you have one.. :D

I got one :D

http://www.xtremesystems.org/forums/...=153578&page=4
08-04-2007, 07:37 PM
MacClipper

Quote:

Originally Posted by TinTin

yes, it is out in HK, but only 10pcs came to HK and all sold in one day.:)

Lucky for you, guess that makes it pointless flying over to get one... j/k :D

Post some findings esp since you list the P5K Premium in your sig too, OK?
08-04-2007, 08:28 PM
erwinz

Quote:

Originally Posted by TinTin

I got one :D

http://www.xtremesystems.org/forums/...=153578&page=4

nice.. :) you can probably create a separate post.. :)

how is the board?? :) your lucky.. :)
08-04-2007, 10:06 PM
TinTin

Quote:

Originally Posted by erwinz

nice.. :) you can probably create a separate post.. :)

how is the board?? :) your lucky.. :)

just install the window, it is now running at 400X8 at default VID (1.2875V)

now using 120 extreme :D

Just can't find where in BIOS can disable the 1394 and the dual Lan :ROTF:

http://www.ocqq.com/bbs/attachment.p...73&nothumb=yes
08-04-2007, 10:34 PM
GAR

nice board!!!!!!!!!!!!
08-04-2007, 10:39 PM
Brother Esau

Quote:

Originally Posted by TEDY

apeman 69 lower you sig.

Yea Really man kill the voltage!!!!
08-04-2007, 10:54 PM
TinTin

Quote:

Originally Posted by MacClipper

Lucky for you, guess that makes it pointless flying over to get one... j/k :D

Post some findings esp since you list the P5K Premium in your sig too, OK?

yes sure, P5K Premium is also a solid MB but P35-T2R is sexy.

because now I am using a new G0 Q6600, so I can't compare the overclockability of the two boards, and also the performance at this moment.

But I just find the Vdroop of P35-T2R is abt 0.04V with Damper enable while the Premium is abt 0.02-0.03V, both at full load.

and also the Vdimm drop of P35-T2R is abt 0.07V, e.g. I set 2.19V in BIOS, it shows 2.12Vin window, this seems to be real, coz I get error in ortho. (since my ram is capable of running DDR1000 CL-4-4-4-5 at 2.15V, lower Vdimm will have error) :eek:

So I hope if any users who own this MB can report the same issue :)
08-05-2007, 01:21 AM
mb.

I hope this board will be available soon in Europe! Some German retailers already listing it from €230 - €270 but none at stock yet. I am willing to pay €250.
08-05-2007, 01:30 AM
leoftw

took me like a year to load the first page but its worth it . Nice looking board
08-05-2007, 01:55 AM
erwinz

Quote:

Originally Posted by TinTin

yes sure, P5K Premium is also a solid MB but P35-T2R is sexy.

because now I am using a new G0 Q6600, so I can't compare the overclockability of the two boards, and also the performance at this moment.

But I just find the Vdroop of P35-T2R is abt 0.04V with Damper enable while the Premium is abt 0.02-0.03V, both at full load.

and also the Vdimm drop of P35-T2R is abt 0.07V, e.g. I set 2.19V in BIOS, it shows 2.12Vin window, this seems to be real, coz I get error in ortho. (since my ram is capable of running DDR1000 CL-4-4-4-5 at 2.15V, lower Vdimm will have error) :eek:

So I hope if any users who own this MB can report the same issue :)

mm.. for a 300usd board.. not a good sign.. mm..

hey what psu are you using.. :) DFI is prone to psu incompatibility... :D
08-05-2007, 05:28 AM
TinTin

Quote:

Originally Posted by erwinz

mm.. for a 300usd board.. not a good sign.. mm..

hey what psu are you using.. :) DFI is prone to psu incompatibility... :D

:D
The PSU is tagan
08-05-2007, 05:31 AM
erwinz

Quote:

Originally Posted by TinTin

It sells at HK$1999 = $US256 :D
The PSU is tagan

oh.. 256usd.. :)

btw.. any results yet? :)
08-05-2007, 05:37 AM
TinTin

Quote:

Originally Posted by erwinz

oh.. :)

btw.. any results yet? :)

Just a very quick test, many things not yet test, e.g. FSB limit (MB&CPU), Ram performance.....:)

UV effect :D
http://bbs.ocqq.com/attachment.php?a...68&nothumb=yes

A qucik set up
http://bbs.ocqq.com/attachment.php?a...79&nothumb=yes

Q6600 G0 @ 445X9, superpi 1M benchable.
http://bbs.ocqq.com/attachments/foru....jpg.thumb.jpg
08-05-2007, 06:28 AM
erwinz

Quote:

Originally Posted by TinTin

Just a very quick test, many things not yet test, e.g. FSB limit (MB&CPU), Ram performance.....:)

UV effect :D
http://bbs.ocqq.com/attachment.php?a...68&nothumb=yes

A qucik set up
http://bbs.ocqq.com/attachment.php?a...79&nothumb=yes

Q6600 G0 @ 445X9, superpi 1M benchable.
http://bbs.ocqq.com/attachments/foru....jpg.thumb.jpg

nice results.. :)

hope someone post same results.. :) so we can compare the speed.. :)

hey can you compare with your previous setup?? :)

btw you have a PM :D
08-05-2007, 06:40 AM
EternityZX9

Quote:

Originally Posted by jimmyz

i checked that link and it says 10 available. i chose checkout and the number dropped to 9. it seems they have a few in stock? i have to spend a little money this weekend or i would go ahead and buy it.

Well the good thing is I've never heard of that place before so obviously they have a small quantity. Obviously larger dealers will get larger shipments. It's just a matter of time now...

Q6600 G0 + DFI P35 T2R + 8800GTS Rev. A3....ugh the wait is the killer right now. Can't use my new pc until I get this part. :(
08-05-2007, 04:21 PM
retrospooty

Quote:

Originally Posted by xenolith

This is so DFI's style. Very nice board, but too late to the game and too expensive.

dood, stuff like this takes time, and costs money. I think its perfect and well worth the wait. I will gladly pay $300 immediately. Anyone got links or dates ?
08-05-2007, 04:48 PM
Haltech

MotherboardPro shows availability on 8/25. The egg and everyone else should have them around the same time. Generally the egg sells at a markup when something like this is released!
08-05-2007, 04:52 PM
shimmishim

Quote:

Originally Posted by retrospooty

dood, stuff like this takes time, and costs money. I think its perfect and well worth the wait. I will gladly pay $300 immediately. Anyone got links or dates ?

i agree with you and tony and everyone else...

but asus released their p5k series decently early at or around $250 and they're quite the good board... it has its quirks here and there but all boards do

if dfi were to release their board the same time as Asus, I'd be willing to pay $300 for it as well...
08-05-2007, 04:58 PM
xenolith

Quote:

Originally Posted by retrospooty

dood, stuff like this takes time, and costs money. I think its perfect and well worth the wait. I will gladly pay $300 immediately. Anyone got links or dates ?

Dooood, thank you for stating the obvious - "stuff like this takes time, and costs money." In your opinion it's perfect - that which you don't even have possession or know the price of yet - but you have a right to that opinion. I just hope you realise I have a right to mine too.
08-05-2007, 05:06 PM
xenolith

Quote:

Originally Posted by shimmishim

i agree with you and tony and everyone else...

but asus released their p5k series decently early at or around $250 and they're quite the good board... it has its quirks here and there but all boards do

if dfi were to release their board the same time as Asus, I'd be willing to pay $300 for it as well...

I agree. I would have seriously considered this board @ $300 just six weeks ago.
08-05-2007, 05:46 PM
ripken204

Quote:

Originally Posted by Haltech

MotherboardPro shows availability on 8/25. The egg and everyone else should have them around the same time. Generally the egg sells at a markup when something like this is released!

crap i was hoping that it would come out sometime this week... i dont want to and cant wait that long.
08-05-2007, 06:57 PM
jkresh

8/25 is too close to x38 for availability (assuming x38 isint delayed again). And its price will be close to x38 as well, really hard to justify $300 for a p35 board.
08-05-2007, 10:13 PM
pumbertot

absolutely beautiful, a work of art. now I await their X38 board, SLI is a must for me so no P35. :(
08-06-2007, 12:01 AM
mucker

...since we have to wait anyway, SLI/X38 results are worth a peek.....
08-06-2007, 02:04 AM
Tony

Finally received a full retail release A03, turned down a pre release to make sure i got what you guys will see. Rgone has one also and will be posting on the DFI support forum as soon as he starts testing.

Shipments hit EU and USA early next week with retail shipments next week also i just heard, so if you are thinking of getting one watch the usual DFI outlets closely.

Million things to do here so please don't push for results, I will post as soon as I can.

T
08-06-2007, 02:06 AM
Tony

X38 is late October I heard, has this changed?
08-06-2007, 02:16 AM
OBR

I have this mobo and layout is not good for watercooling, this mobo is AVERAGE mobo, DFI is not HIGH-end anymore ...

I have better scores on every test with nForce mobo or Asus P35 mobo, now i am working on review and ... this is third DFI mobo in-line where will be my Review result BAD!
08-06-2007, 02:23 AM
Tony

So your one bad experience proves to the world that the board is AVERAGE as you put it?

Get real man, half the issues i ever see are user based with the user not fully knowing the best way to tweak a board. I have seen everyone become fixated with FSB of late and judged how good a board is on how close to 500 (now 600) FSB the board will run, with those who have studied where the boards are fastest it is really not worth the effort.

I have a board here and many more will have boards next week, i think it best we judge the board by how a broad range of users do...not just your results and the lack of a "water cooler friendly" layout at this time.

Remember it is not possible to please everyone, thats why we have so many different brands of motherboards out there, just like there are many different brands of sneakers.
08-06-2007, 03:09 AM
TinTin

Quote:

Originally Posted by Tony

Finally received a full retail release A03, turned down a pre release to make sure i got what you guys will see. Rgone has one also and will be posting on the DFI support forum as soon as he starts testing.

Shipments hit EU and USA early next week with retail shipments next week also i just heard, so if you are thinking of getting one watch the usual DFI outlets closely.

Million things to do here so please don't push for results, I will post as soon as I can.

T

Hi, Tony,

I got the MB two days ago, but I found there is about 0.07V Vdimm droop after entering the windows as reported by the ITE software. It seems true coz I get error an such voltage. Is it my MB faulty? :)
08-06-2007, 04:47 AM
EnJoY

Quote:

Originally Posted by TinTin

Hi, Tony,

I got the MB two days ago, but I found there is about 0.07V Vdimm droop after entering the windows as reported by the ITE software. It seems true coz I get error an such voltage. Is it my MB faulty? :)

Hmmm...is it a true droop or is the software simply reporting incorrectly? Measure the voltage with a DMM both in bios and in windows and measure under load in memtest and in windows memtest/prime95 and see how your results compare. .07 isn't crazy, but it is a tad high if it's correct. In either case I doubt it's a "faulty" board.

@Tony: I can't wait to talk to you about your results with this board on Skype, I'm eager to here how it performs on the tighter straps. ;)
08-06-2007, 11:14 AM
Yoxxy

Quote:

Originally Posted by Tony

Get real man, half the issues i ever see are user based with the user not fully knowing the best way to tweak a board. I have seen everyone become fixated with FSB of late and judged how good a board is on how close to 500 (now 600) FSB the board will run, with those who have studied where the boards are fastest it is really not worth the effort.

Didn't Team Japan continually break pi records with 570-580 fsb?
08-06-2007, 11:53 AM
shimmishim

Quote:

Originally Posted by Yoxxy

Didn't Team Japan continually break pi records with 570-580 fsb?

i agree with yoxxy... but isn't part of that having to do with the fact it was done with a magically delicious 6700 (in other words top locked at 10x)?

it'd be interesting to see if there were a X6800 that was capable of 5700-5800 1M pi using higher mults, lower fsb, dividers to get mem 600+ and see if it would indeed be faster than the 6700 since according to Tony higher fsb isn't necessarily better. :shrug:
08-06-2007, 02:11 PM
palese

Quote:

Originally Posted by Tony

Finally received a full retail release A03, turned down a pre release to make sure i got what you guys will see. Rgone has one also and will be posting on the DFI support forum as soon as he starts testing.

Shipments hit EU and USA early next week with retail shipments next week also i just heard, so if you are thinking of getting one watch the usual DFI outlets closely.

Million things to do here so please don't push for results, I will post as soon as I can.

T

Just please don't test it with a ES cpu, retail cpu never performs the same, this will eliminate the hype:)
08-06-2007, 03:47 PM
Tony

I have a retail X6800, no quads, or I have ES6750 and ES6850 or 6400 Allendale.

So it looks like tests will be with the 6800 to keep you happy ;)
08-06-2007, 04:11 PM
Tony

Super pi is all about access latency, you can reduce the latency with outright memory speed or you can tweak the chipset and the ram to have the lowest latency it can run and the scores will be equally as fast.

You have to remember to get boards running high FSB's internal latencies have to be relaxed....now if you are chilling the CPU you also chill the board and this has a real positive affect on how well the board clocks up and "may" allow latencies to be tightened again. For most mortals running water or high end air the latency has to remain high and so you lose speed due to increased access latency.

This is why for me 600fsb is worthless, as the boards are running very loose latency to do this and there is no real speed gained, I would much rather run 450ish FSB and ubber tight latency on the chipset and memory with half decent Vmem also ;)
08-06-2007, 05:18 PM
ripken204

so does anyone know when this board is coming out?
tankguys should have all of the Q6600 g0's delivered sometime next week, so i need a board asap..
08-06-2007, 05:39 PM
xenolith

Quote:

Originally Posted by ripken204

so does anyone know when this board is coming out?
tankguys should have all of the Q6600 g0's delivered sometime next week, so i need a board asap..

motherboardpro.com moved it up to 8/20... even if it does come in earlier than that elsewhere, you better act fast, pull down your pants and bend over...
08-06-2007, 06:13 PM
Capt_Caveman

Quote:

Originally Posted by xenolith

motherboardpro.com moved it up to 8/20... even if it does come in earlier than that elsewhere, you better act fast, pull down your pants and bend over...

LMAO
08-06-2007, 06:48 PM
idiotekniQues

it's purty
08-06-2007, 07:14 PM
palese

Quote:

Originally Posted by Tony

I have a retail X6800, no quads, or I have ES6750 and ES6850 or 6400 Allendale.

So it looks like tests will be with the 6800 to keep you happy ;)

Tony you are the man:D
08-06-2007, 10:43 PM
Kin Hell

Quote:

Originally Posted by erwinz

alright.. DFI uses screws on the NB and SB.. :D

Nice to see those crappy Hooks are gone. :toast2: Looks like someone heard the Cry to stop using Hooks back on the RD600 Thread!
Does anyone know if this is this just a DFI thing or have Intel dropped Hooks for ever!?

It also appears no one can Explain why this Intel Board has nVidia Raid?? I've read this thread backwards & forwards in case I missed relevant info, but several questions have asked "why", with no reply yet!? Beats the crap outta me considering other Intel boards Boast the Slick Matrix RAID. :shrug:
Can anyone shed some light on "WHY" nVidia RAID & perhaps one of you lucky fellas to already have this board could post some HD Tach results for a couple of Striped SATA150's. :up:
Thanks for info & Nice Pics Andre...Sexy looking board! :)
08-06-2007, 11:17 PM
alpha0ne

How can a board not be WC friendly :rolleyes: :confused:

Never seen that before :shrug:
08-06-2007, 11:21 PM
Kin Hell

Quote:

Originally Posted by alpha0ne

How can a board not be WC friendly :rolleyes: :confused:

Never seen that before :shrug:

The heatpipe transfers are the problem. Removing the NB means you have to find an alternative cooling solution for the rest of the components. Those being the SB & Digital PWM. Thats one helluva SB plate for a P35 board imo but then the 680i is another chipset that demands Water Cooling for the SB and is poorly cooled with Stock Blocks. PWM's get really HOT & DFI appear to have dropped a large lump of metal & External Hetpipe/Fin option to address this issue. As soon as you Water Cool the CPU, those mofsets are hitting 100+ Deg C for no downdraught when using a conventional Heatsink/Fan combo! Unfortunately, I cant cool the SB on my 680i as my 7950 GX2's inner card hangs right over the SB. There are blocks that will fit but I aint happy with the mounts & they arn't specifically designed for the Chipset. I'm considering this board to be rid of VDroops but the use of nVidia RAID concerns the crap out of me! :shakes:
08-07-2007, 04:06 PM
Heidfirst

Quote:

Originally Posted by Kin Hell

It also appears no one can Explain why this Intel Board has nVidia Raid?? I've read this thread backwards & forwards in case I missed relevant info, but several questions have asked "why", with no reply yet!? Beats the crap outta me considering other Intel boards Boast the Slick Matrix RAID. :shrug:
Can anyone shed some light on "WHY" nVidia RAID

it's a misprint - the manual has ICH9R & the driver download is Intel.
08-07-2007, 05:05 PM
EternityZX9

Quote:

Originally Posted by xenolith

motherboardpro.com moved it up to 8/20... even if it does come in earlier than that elsewhere, you better act fast, pull down your pants and bend over...

Does anyone know if motherboardpro is a reliable vendor? Cause I'd like to get this board...but I've never heard of them.
08-07-2007, 05:39 PM
cyberspyder

Quote:

Originally Posted by Kin Hell

The heatpipe transfers are the problem. Removing the NB means you have to find an alternative cooling solution for the rest of the components. Those being the SB & Digital PWM. Thats one helluva SB plate for a P35 board imo but then the 680i is another chipset that demands Water Cooling for the SB and is poorly cooled with Stock Blocks. PWM's get really HOT & DFI appear to have dropped a large lump of metal & External Hetpipe/Fin option to address this issue. As soon as you Water Cool the CPU, those mofsets are hitting 100+ Deg C for no downdraught when using a conventional Heatsink/Fan combo! Unfortunately, I cant cool the SB on my 680i as my 7950 GX2's inner card hangs right over the SB. There are blocks that will fit but I aint happy with the mounts & they arn't specifically designed for the Chipset. I'm considering this board to be rid of VDroops but the use of nVidia RAID concerns the crap out of me! :shakes:

THERMALRIGHT TIME BABY!!!!! :D :ROTF:
08-07-2007, 09:34 PM
Spanki

Quote:

Originally Posted by EternityZX9

Does anyone know if motherboardpro is a reliable vendor? Cause I'd like to get this board...but I've never heard of them.

Me either, but I got the link from DFI's website as an authorized dealer. Whether that says anything about thier business practices, I don't know.:shrug:
08-08-2007, 04:00 AM
shimmishim

Quote:

Originally Posted by EternityZX9

Does anyone know if motherboardpro is a reliable vendor? Cause I'd like to get this board...but I've never heard of them.

from what i've heard from others on XS, MBP appears to be a reliable vendor. many people that got the first round of DFI 680i boards got it from here.

i say you're safe getting it from here.
08-08-2007, 04:29 AM
Grinch

Quote:

Originally Posted by EternityZX9

Does anyone know if motherboardpro is a reliable vendor? Cause I'd like to get this board...but I've never heard of them.

:up: awesome vendor!
08-08-2007, 05:30 AM
Sailindawg

@Tony OCZ

When you get the time, can you also clock this board with one of your lesser retail cpu's? It would give us more mortal types a better idea of how the board can do with a more average cpu.

Thanks.
08-08-2007, 05:41 AM
AcuraDC5

Board is just plain sexy
08-08-2007, 06:24 AM
Fr3ak

Seems to be a really nice board.
Question now is how good and reliable is the digital PWR for high voltages when extreme cooling is being used.

X38 boards will hit the stores earlier than end of october from what I heard.
08-08-2007, 01:27 PM
EternityZX9

Quote:

Originally Posted by shimmishim

from what i've heard from others on XS, MBP appears to be a reliable vendor. many people that got the first round of DFI 680i boards got it from here.

i say you're safe getting it from here.

Quote:

Originally Posted by Grinch

:up: awesome vendor!

Alright. I'm going to take your word for it. And I also saw njkid32's good rating on resellerrating.

Pre-ordered. :)
08-08-2007, 05:55 PM
AndreYang

New BIOS Memory Control is so stronger.

Here is LOW Voltage DDR2 1200 CL5-5-5-15 Dual 32M

http://www.iamxtreme.net/andre/P35-T2R/1200-1.PNG

http://www.iamxtreme.net/andre/P35-T2R/1200-2.PNG

If you have this mobo, you could pm me to receive new BIOS.

Andre
08-08-2007, 06:04 PM
ziddey

wowowowow. d9gmh doing 600 with 1.9v??? what's it able to do at 1.9v in other p35 like p5k?
08-08-2007, 06:08 PM
DMH

1.9V for 600Mhz???I want that pair of dimms:DHas anyone posted differences beetwen the use of that thingy(can't remember the name) to use outside the case??
08-08-2007, 06:13 PM
bypolar

Last I seen http://http://www.motherboardpro.com...T2R-p-338.html

had 26 comming to the states.

Info= Joefriday from DFI Club

hey, and looks like another great Board from DFI, surprising they are early this time for them.
08-08-2007, 06:15 PM
shimmishim

wow, that's some amazing memory Andre... or is it a combination of the board and memory :)

either way, great results!
08-08-2007, 06:53 PM
TinTin

Quote:

Originally Posted by AndreYang

New BIOS Memory Control is so stronger.

Here is LOW Voltage DDR2 1200 CL5-5-5-15 Dual 32M

http://www.iamxtreme.net/andre/P35-T2R/1200-1.PNG

http://www.iamxtreme.net/andre/P35-T2R/1200-2.PNG

If you have this mobo, you could pm me to receive new BIOS.

Andre

Good, and did it fix the BIOS e.g. can disable on board Lan, 1394....?
BTW, u have a PM :D
08-08-2007, 07:03 PM
AndreYang

Quote:

Originally Posted by ziddey

wowowowow. d9gmh doing 600 with 1.9v??? what's it able to do at 1.9v in other p35 like p5k?

I cannot do 1.9V on other P35 mobos, such P5K series.
08-08-2007, 07:04 PM
AndreYang

Quote:

Originally Posted by TinTin

Good, and did it fix the BIOS e.g. can disable on board Lan, 1394....?
BTW, u have a PM :D

It already fixed and I send you new BIOS.:)
08-08-2007, 07:07 PM
TinTin

Quote:

Originally Posted by AndreYang

It already fixed and I send you new BIOS.:)

Thanks :D
I will move to DFI P35-T2R from P5K-P tonight, hoping getting good result too!! :)
08-08-2007, 07:14 PM
erwinz

Quote:

Originally Posted by TinTin

Thanks :D
I will move to DFI P35-T2R from P5K-P tonight, hoping getting good result too!! :)

nice.. :) hey is there new stocks of this board in HK.. :D please PM me.. ;)
08-08-2007, 07:17 PM
erwinz

Quote:

Originally Posted by AndreYang

I cannot do 1.9V on other P35 mobos, such P5K series.

hey Andre can you please check if your rams memtest86 1.7 stable @ 600 mhz at that voltage.. :)

or maybe just running 30 min of orthos blend priority 9 on that settings.. :D
08-08-2007, 07:19 PM
GripS

Quote:

Originally Posted by TinTin

Thanks :D
I will move to DFI P35-T2R from P5K-P tonight, hoping getting good result too!! :)

?? So you have been sitting on this board for a while? I would have thrown it in my setup the day i got it.:rolleyes:
08-08-2007, 07:20 PM
Haltech

Andre, what ram is that?
08-08-2007, 07:29 PM
MacClipper

Quote:

Originally Posted by GripS

?? So you have been sitting on this board for a while? I would have thrown it in my setup the day i got it.:rolleyes:

Both are designed to fly mobos, wonder which will end up the eventual winner.
08-08-2007, 07:37 PM
TinTin

Quote:

Originally Posted by GripS

?? So you have been sitting on this board for a while? I would have thrown it in my setup the day i got it.:rolleyes:

I have set it up in the second day I have owned it but with normal air-cooling only, but all my other stuffs are in my other home, so I can't test it with watercooling and the same condition, while I have tested all the result of my P5K-P with watercooling, so i want to be fair to the two MBs.

Initial test @4GHz by air-cooling: http://www.xtremesystems.org/forums/...&postcount=129

And I have played 4367MHz of my Q6600 last night, so now I can totally move to DFI to test it such as for 24/7 setting, limit of the MB. ;)
08-08-2007, 07:56 PM
erwinz

Quote:

Originally Posted by TinTin

I have set it up in the second day I have owned it but with normal air-cooling only, but all my other stuffs are in my other home, so I can't test it with watercooling and the same condition, while I have tested all the result of my P5K-P with watercooling, so i want to be fair to the two MBs.

Initial test @4GHz by air-cooling: http://www.xtremesystems.org/forums/...&postcount=129

And I have played 4367MHz of my Q6600 last night, so now I can totally move to DFI to test it such as for 24/7 setting, limit of the MB. ;)

nice.. :) a good comparison.. Asus P5K Premium and DFI P35 Lanparty.. :) I think it deserve a new thread for your posting.. :)

can't wait for it.. :) hey the way.. how is the memory controller of Asus Premium?? does it do DDR2 600 mhz 1.9 volts for your memory?? :)
08-08-2007, 07:59 PM
TinTin

Quote:

Originally Posted by erwinz

nice.. :) a good comparison.. Asus P5K Premium and DFI P35 Lanparty.. :) I think it deserve a new thread for your posting.. :)

can't wait for it.. :) hey the way.. how is the memory controller of Asus Premium?? does it do DDR2 600 mhz 1.9 volts for your memory?? :)

My rams are not that stronger, 2.25V @ DDR1200 CL5-5-5, and 2.40V @ DDR1250 CL5-5-5, but they are memtest passed voltage.;)

@ DR 1000, 600% passed
http://bbs.ocqq.com/attachments/foru....jpg.thumb.jpg

@ DDR 1250, 300% passed
http://bbs.ocqq.com/attachments/foru....jpg.thumb.jpg
08-08-2007, 08:01 PM
erwinz

Quote:

Originally Posted by TinTin

My rams are not that stronger, 2.25V @ DDR1200 CL5-5-5, and 2.40V @ DDR1250 CL5-5-5, but they are memtest 600% passed voltage ;)

memtest stable is much more impressive for me.. :) DDR2 1200 for 2.25 vdimm is nice.. is that on the Asus Premium or DFI P35 LP??
08-08-2007, 08:03 PM
TinTin

Quote:

Originally Posted by erwinz

memtest stable is much more impressive for me.. :) DDR2 1200 for 2.25 vdimm is nice.. is that on the Asus Premium or DFI P35 LP??

P5K-P :D
08-08-2007, 08:08 PM
erwinz

Quote:

Originally Posted by TinTin

P5K-P :D

hahaha.. man I can't for your results.. :)

Asus P5K Premium vs DFI P35 Lanparty

:woot:
08-08-2007, 08:09 PM
TinTin

Quote:

Originally Posted by erwinz

hahaha.. man I can't for your results.. :)

Asus P5K Premium vs DFI P35 Lanparty

:woot:

Now I have enough test data before I go to DFI :D ;)
08-08-2007, 08:09 PM
fireice2

:rocker: DFI really rock! and this time it realy ain't late for the party!. :d

@ erwin

can't wait for the x38 version? :D
08-08-2007, 08:15 PM
erwinz

Quote:

Originally Posted by fireice2

:rocker: DFI really rock! and this time it realy ain't late for the party!. :d

@ erwin

can't wait for the x38 version? :D

hahaha.. I can wait.. :) but this is hard to ignore.. :) hope there are less vdrops..
08-08-2007, 08:16 PM
erwinz

Quote:

Originally Posted by TinTin

Now I have enough test data before I go to DFI :D ;)

hey bro can you also takenote of the vdrop.. :) hehehe.. how is the vdrop on the Premium during load using quadcore??
08-08-2007, 08:19 PM
TinTin

Quote:

Originally Posted by erwinz

hey bro can you also takenote of the vdrop.. :) hehehe.. how is the vdrop on the Premium during load using quadcore??

for Premium with Damper enable,

At 1.4000V (BIOS), Idle = 1.37V, full load = 1.37V
At 1.6375V (BIOS), Idle = 1.61V, full load = 1.62V

;)
08-08-2007, 08:22 PM
fireice2

Quote:

Originally Posted by erwinz

hahaha.. I can wait.. :) but this is hard to ignore.. :) hope there are less vdrops..

:eek2: you're gonna get 2 boards?! hehehee
08-08-2007, 08:27 PM
erwinz

Quote:

Originally Posted by TinTin

for Premium with Damper enable,

At 1.4000V (BIOS), Idle = 1.37V, full load = 1.37V
At 1.6375V (BIOS), Idle = 1.61V, full load = 1.62V

;)

really nice of Asus for having a Voltage Damper option.. :) hahaha.. seems like they are listening for there consumers.. :)

now the DFI awaits.. mm.. last time you said 0.07 vdrop right?? hope its only on the Smart guardian.. they should have update the software.. hehehe ;)

Quote:

Originally Posted by fireice2

:eek2: you're gonna get 2 boards?! hehehee

hehehe.. not really.. maybe.. I don't know.. hahahaha
08-08-2007, 08:46 PM
fireice2

Don't hold back bro. :D I hope my bank account would be enough by the time the x38 boards arrive. hehehe

do you accept trade-ins? :D
08-08-2007, 10:14 PM
AndreYang

Quote:

Originally Posted by erwinz

hey Andre can you please check if your rams memtest86 1.7 stable @ 600 mhz at that voltage.. :)

or maybe just running 30 min of orthos blend priority 9 on that settings.. :D

Blend need some voltage, but it's still better than other mobos.

http://www.iamxtreme.net/andre/P35-T2R/1200-Blend.PNG
08-08-2007, 10:18 PM
AndreYang

Quote:

Originally Posted by Haltech

Andre, what ram is that?

Old school GSKILL 6HD22 D9GMH
08-08-2007, 10:18 PM
I34z1k

Hey guys.. What's the default voltage on this board? I don't want posting issues like with my p5k :(

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 06:32 AM.

XtremeSystems