Micron D9 GMH\GKX\JKH etc club

Printable View

Show 100 post(s) from this thread on one page

03-05-2009, 12:11 AM
simone18

Quote:

On a DFI P35. Still, nice result.

tnx man ;)
your tg pc6400 has gkx or gmh chip?
03-05-2009, 12:56 AM
CryptiK

Quote:

Originally Posted by Ch@pS

http://img165.imageshack.us/img165/1875/10433.jpg

Managed this with my Team Xtreem D9GMH, any suggestions to get them over 11k read? Its what I'm aiming for.

On P45 (not a DFI) you will need around 540 FSB to break 11K read without using a high CPU clock to 'cheat'.

You can see in the SS below I am close to 11K at 533 FSB, but to get the FSB any higher I had to back off some chipset settings so I lost some efficiency, which means I had to go up to 540 FSB (shown on second SS) to break 11K.

http://i720.photobucket.com/albums/w...edCTstrong.jpg

Here is a run that is the lowest settings I can use to break 11K read. I use a low CPU clock of 3.78GHz so it just shows the raw power of the FSB and ram speed.

http://i720.photobucket.com/albums/w...MHz11Kread.jpg
03-05-2009, 02:36 AM
simone18

i'll try your same settings cryptic, just to verify if it's true that m2f sux at speed against ud3r p45. i've heard about it but i never verified :)
03-05-2009, 06:15 AM
Mafio

the new ep45 extreme is here :D
03-05-2009, 10:41 AM
simone18

go for extreme oc man, i'm waiting screens...will it be pwnage? :D
03-05-2009, 11:42 AM
okorop

Quote:

Originally Posted by Mafio

the new ep45 extreme is here :D

I am waiting for your screen :)
03-05-2009, 01:32 PM
Mafio

this afternoon i tried the crucial ballistix of my friend Guglio on my new ep45 extreme. :yepp:

this ram is spectacular...

1400mhz cas5 2.4volt

http://www.pctunerup.com/up/results/..._screen010.jpg

1200 cas4 2.4volt

http://www.pctunerup.com/up/results/..._screen011.jpg

1225 cas4 2.45 volt

http://www.pctunerup.com/up/results/..._screen012.jpg
03-05-2009, 01:34 PM
simone18

well done :clap:
but...no more than 1400 cas5? do you try 2.5+v? :D
03-05-2009, 02:22 PM
okorop

@Mafio good start.....now overclock the ram :)
03-05-2009, 03:32 PM
Shiranui Gen-An

1 Attachment(s)

This is my new Patriot kit on 2.06V real:
03-05-2009, 03:37 PM
Bigred1

3 Attachment(s)

Pulled these from and old HP Media Center PC. Loving them allready. I know they will go higher but I cant seem to get my DFI BloodIron P35 board to do it.It craps out past 1150 dual channel. I must not being doing something right.

DDR2 1100 Cas5 @ 2.0v
03-05-2009, 03:57 PM
Shiranui Gen-An

JEDEC PCB probably holding you back.
03-05-2009, 04:03 PM
cdawall

Quote:

Originally Posted by Shiranui Gen-An

JEDEC PCB probably holding you back.

doubtful they are pretty good as far as PCB's go same PCB my D9DCD's use and those do 1120 CL4
03-05-2009, 04:17 PM
Bigred1

Quote:

Originally Posted by Shiranui Gen-An

JEDEC PCB probably holding you back.

I dont think its that because I have a pair of OCZ Reaper 1150s that will do 1150 single channel but not dual channel. I think its the auto timings the board giving it but im not sure what sub timings to change to give stability. Or I'm just bad with ram lol.
03-05-2009, 04:33 PM
tool_462

I've run some D9's up to 1350 CAS 5 in dual channel on Blood Iron, for what its worth.
03-05-2009, 07:23 PM
Bigred1

Quote:

Originally Posted by tool_462

I've run some D9's up to 1350 CAS 5 in dual channel on Blood Iron, for what its worth.

If you could help me achieve that it would be greatly appreciated.:up:
03-05-2009, 09:01 PM
whe3ls

Quote:

Originally Posted by tool_462

I've run some D9's up to 1350 CAS 5 in dual channel on Blood Iron, for what its worth.

i have been 1200 or so
03-06-2009, 12:29 AM
PizzaMan

Ballistix Tracers, double sided. 2.35v 1300Mhz. I believe this pair is GKX, but I'm not sure. The don't like T1 and cas 3, but they scream with cas 4 and 5. ICs just say 'Ballistix' and '-f17' Not totaly stable at 1300. Can run SuperPi and other benchies but crap in RL gaming.

http://valid.canardpc.com/show_oc.php?id=519358
03-06-2009, 04:20 AM
simone18

Quote:

Pulled these from and old HP Media Center PC.

rotfl! hp building ht pc with high end ram...incredible :)
03-06-2009, 07:07 AM
Bigred1

Quote:

Originally Posted by simone18

rotfl! hp building ht pc with high end ram...incredible :)

I couldn't believe it either. I have been looking everywhere for some sticks of D9 and i found them in the one place you wouldnt think to look, An HP:shocked:
03-06-2009, 08:28 AM
zsamz_

Quote:

Originally Posted by Bigred1

I couldn't believe it either. I have been looking everywhere for some sticks of D9 and i found them in the one place you wouldnt think to look, An HP:shocked:

you would be surprised but i seen many d9 in hp pcs:yepp:
03-06-2009, 09:15 AM
okorop

Quote:

Originally Posted by simone18

rotfl! hp building ht pc with high end ram...incredible :)

OMG
03-06-2009, 09:26 AM
Mafio

cellshock pc8000 + crucial ballistix pc8500 on my ep45 extreme

1200mhz cas4 @2.4volt ;)

http://forum.hwproject.net/imagehost...15bd6221a3.jpg

guys, this mobo kick ass :yepp:
03-06-2009, 09:29 AM
okorop

Quote:

Originally Posted by Mafio

cellshock pc8000 + crucial ballistix pc8500 on my ep45 extreme

1200mhz cas4 @2.4volt ;)

http://forum.hwproject.net/imagehost...15bd6221a3.jpg

guys, this mobo kick ass :yepp:

congratulations....really a good result with 4 dimm ram :)
03-06-2009, 09:53 AM
radaja

great job mafio.
03-06-2009, 09:57 AM
Mafio

Quote:

Originally Posted by radaja

great job mafio.

thx mate
03-07-2009, 08:00 AM
eva2000

Plucked in Team PC2-10400 CAS6 Micron D9 memory for some max validation and pulled off my own personal best at 706Mhz 5-5-5-15 at 2.49v bios set vdimm dual channel :D

http://valid.canardpc.com/cache/banner/522198.png

http://fileshosts.com/intel/DFI/DFI_..._validated.png
03-07-2009, 08:05 AM
Shiranui Gen-An

Eva you keep defying the common logic that says D9GKX doesn't play nice with the DFI P35...
03-07-2009, 08:34 AM
[XC] Oj101

Don't those modules come in D9GMH flavours as well? I'm pretty sure I heard that but don't quote me on it.
03-07-2009, 08:55 AM
tool_462

Quote:

Originally Posted by Oj101

Don't those modules come in D9GMH flavours as well? I'm pretty sure I heard that but don't quote me on it.

Yes they do.
03-07-2009, 10:33 AM
zsamz_

Quote:

Originally Posted by Shiranui Gen-An

Eva you keep defying the common logic that says D9GKX doesn't play nice with the DFI P35...

its not logic none of my d9gkx like my dfi board
even some nice d9gmh dont play nice
03-07-2009, 11:37 AM
Shiranui Gen-An

Quote:

Originally Posted by tool_462

Yes they do.

I've never heard of Team using GMH in anything higher than DDR2-8500.
03-07-2009, 11:44 AM
fatguy1992

Quote:

Originally Posted by Shiranui Gen-An

I've never heard of Team using GMH in anything higher than DDR2-8500.

The DDR2 RAM lists says the PC2-10400 has GKX and GMH.

http://ramlist.i4memory.com/ddr2/
03-07-2009, 03:16 PM
Shiranui Gen-An

Quote:

Originally Posted by fatguy1992

The DDR2 RAM lists says the PC2-10400 has GKX and GMH.

http://ramlist.i4memory.com/ddr2/

That's news to me, all the pics of naked Team 1300 I've seen have had D9GKX ICs. If anyone has any TXDD2048M1300HC6DC with D9GMH I'd love to see it.
03-07-2009, 03:24 PM
WaterFlex

Guys, anyone has "Red Devil" 9200 CellShocks?
03-07-2009, 03:30 PM
Shiranui Gen-An

Quote:

Originally Posted by WaterFlex

Guys, anyone has "Red Devil" 9200 CellShocks?

You do :p: And supershanks over at Clunk.org has a pair. I missed out on a kit that showed up within the past couple of weeks on eBay because I didn't go for the Buy it Now price and ended up getting outbid :mad:
03-07-2009, 08:47 PM
CryptiK

Nice work eva :)

Some quick runs on P5Q-D

580 FSB / 580 MHz
http://i720.photobucket.com/albums/w...rest580FSB.jpg

590 FSB / 590 MHz
http://i720.photobucket.com/albums/w...rest590FSB.jpg

558.7 MHz CL4 @ 2.26v
http://i720.photobucket.com/albums/w...5587MHzCL4.jpg
03-07-2009, 11:20 PM
eva2000

Quote:

Originally Posted by Shiranui Gen-An

Eva you keep defying the common logic that says D9GKX doesn't play nice with the DFI P35...

Quote:

Originally Posted by fatguy1992

The DDR2 RAM lists says the PC2-10400 has GKX and GMH.

http://ramlist.i4memory.com/ddr2/

Quote:

Originally Posted by Shiranui Gen-An

That's news to me, all the pics of naked Team 1300 I've seen have had D9GKX ICs. If anyone has any TXDD2048M1300HC6DC with D9GMH I'd love to see it.

I have alot of D9GMH and these Team 1300 i have behave more like D9GMH I have so probably not D9GKX but can't confirm as i like the heatspreaders as they are :)

Quote:

Originally Posted by CryptiK

Nice work eva :)

thanks.. not bad yourself :)

maybe time to switch to updated Everest Ultimate 5.xx ?
03-08-2009, 03:14 AM
Shiranui Gen-An

Quote:

Originally Posted by eva2000

I have alot of D9GMH and these Team 1300 i have behave more like D9GMH I have so probably not D9GKX but can't confirm as i like the heatspreaders as they are :)

Aw, c'mon Eva, Team heatspreaders are easy&safe to remove :D
03-08-2009, 08:09 AM
simone18

Quote:

guys, this mobo kick ass

for sure. no words. congrats ;)
03-08-2009, 08:16 AM
westsider

Quote:

Originally Posted by WaterFlex

Guys, anyone has "Red Devil" 9200 CellShocks?

if you want to buy it one georgian guy has 2 kits there
i could give his info
03-09-2009, 04:47 AM
simone18

i need a little information

which of these kit, if so, have micron D9xxx chip?

patriot viper pc9600 nvidia series
patriot viper pc9200
patriot blade pc9600
patriot blade pc9200
03-09-2009, 05:31 AM
Ch@pS

Quote:

Originally Posted by simone18

i need a little information

which of these kit, if so, have micron D9xxx chip?

patriot viper pc9600 nvidia series
patriot viper pc9200
patriot blade pc9600
patriot blade pc9200

ramlist.i4memory.com

Should help you out and a nice future reference.
03-09-2009, 05:39 AM
CryptiK

Can you guys see what the minimum settings (FSB & Ram MHz) are that allow you to break 11K read in everest? Keep CPU speed under 3.8 - 4.0GHz as a higher CPU clock boosts the read score.

You can see in my previous post (here: http://www.xtremesystems.org/forums/...postcount=1502) I did it at 540 FSB & 648 MHz at PL8 on a P45 (M2F) with a CPU clock of 3.78GHz. It would be interesting to compare performance of various boards.

It would also be interesting to use my exact same settings on different boards and see how they compare.
03-09-2009, 05:42 AM
[XC] Oj101

None of those kits are listed though.
03-10-2009, 05:33 AM
Shiranui Gen-An

patriot viper pc9600 nvidia series
Newer product, so I seriously doubt it.
patriot viper pc9200
Someone on the forums bought this kit and said the ICs didn't look like Micron (they had "feet" on them like PSC).
patriot blade pc9600
Those are supposed to be D9GMH.
patriot blade pc9200
I had a kit of these, they weren't Micron. Took them back to Frys.
03-10-2009, 05:35 AM
Shiranui Gen-An

MemoryC's D9 kits have gone down to some nice prices: http://www.memoryc.com/computermemor...price&dir=desc

I remember when the Team 1300 and 1200 were over $200 (like when I bought mine :mad:).
03-10-2009, 06:21 AM
simone18

thanks gen-an, you're really a ram-master :D
03-10-2009, 06:49 AM
simone18

and how about these:

PC2 9600 Reaper
PN: OCZ2RPR1200GK
SN: 008890807000416-1
03-10-2009, 07:30 AM
Shiranui Gen-An

Quote:

Originally Posted by simone18

and how about these:

PC2 9600 Reaper
PN: OCZ2RPR1200GK
SN: 008890807000416-1

Again, highly unlikely. Stick with the known older kits like Team Xtreem 6400/8500/1200/1300, G.Skill 6400HZ/8500HK/8000HZ, double-sided Ballistix with part numbers ending in 16FD2, 16FD3, 16FD5.
03-10-2009, 04:30 PM
zsamz_

dont touch newer patriot stuff you wont find no d9 in them
03-11-2009, 01:36 AM
simone18

and what about kingston hyperX 2x1gb pc8500? are they D9? even if i buy a new kit?
03-11-2009, 04:06 AM
Shiranui Gen-An

Dude, just stick to Team Xtreem. Only confirmed D9 stuff that still seems to be in production.
03-11-2009, 09:57 AM
Mafio

ep45 extreme bios f8 ;)
cellshock pc8000 gkx @ 1000mhz cas3 2.66volt

http://forum.hwproject.net/imagehost...7fb4b53d83.jpg

http://valid.canardpc.com/show_oc.php?id=525060
03-11-2009, 10:04 AM
simone18

very well done mate! congrats! and nice voltage ;)

@gen-an: ok....finally i'll go for tg :)
03-11-2009, 10:13 AM
Mafio

Quote:

Originally Posted by simone18

very well done mate! congrats! and nice voltage ;)

@gen-an: ok....finally i'll go for tg :)

thx mate ;)

finally WE go for tg :D

p.s. doccia, poi skype :yepp:
03-11-2009, 11:03 AM
The Water Dog

I love the Gigabyte Extreme when it comes to memory-oc=)
Nice results Mafio:clap:
03-11-2009, 11:13 AM
Shiranui Gen-An

I don't know how they did it, but MemoryC managed to stock one kit each of Cellshock 8000 C5 (GKX) and 8500 C5 (GMH). Prices are almost too low for em too. Oh well, I have a set of the G.Skill 8000 HZs on the way.
03-13-2009, 06:10 PM
Shiranui Gen-An

Got my G.Skill kit in the other day. Haven't had much luck with them on the DFI X48, gonna try the UD3P.

http://img27.imageshack.us/img27/2525/dsc00131y.jpg http://img17.imageshack.us/img17/395/dsc00132u.jpg http://img21.imageshack.us/img21/9356/dsc00133d.jpg http://img23.imageshack.us/img23/859/dsc00134x.jpg http://img27.imageshack.us/img27/2686/dsc00135n.jpg
03-13-2009, 06:39 PM
radaja

nice photos Shiranui-Gen-An.those cellshocks didnt last long at memoryc.i couldnt believe the price for the one kit 37$.
03-14-2009, 03:33 AM
The Water Dog

Looking forward to see what you can get out of the HZ-set, Shiranui-Gen-An:D
03-14-2009, 04:50 AM
CryptiK

I pushed my begrudging board a couple of MHz higher than my previous everest max speed of 660 MHz, to 667.5 MHz using my TG 8500's.

http://i720.photobucket.com/albums/w...est6675MHz.jpg
03-18-2009, 11:54 PM
CryptiK

Getting better, managed 672 MHz CL5. ignore the bench results its at low FSB and PL 10.

http://i720.photobucket.com/albums/w...672MHz240v.jpg
03-19-2009, 04:51 AM
lha

What do you think about this result http://valid.canardpc.com/show_oc.php?id=530225 ?
M2F isnt the best dual channel extreme ram mobo.
and btw i was using PL6
03-19-2009, 05:16 AM
CryptiK

Iha - really nice work there, care to share your settings and BIOS version? 1:2 divider doesn't play nice on my board it wont even POST, I'll try flashing to another BIOS and seeing if it works.

For 672 MHz I used:

1.35 vNB
2.40 vdimm
NB DDR Ref +37.5mv
DDR2 CHA/CHB Ref +12.5mv
PL10
5:8 divider
03-19-2009, 05:22 AM
GeorgeStorm

Hey
I have the chance to buy some Crucial Ballistix Tracer D9 1bg modules,
2 for £25,
Good deal?
Also thinking of getting the HZ kit available here, 45$ shipped....... (just over £30)
Is either better theoretically? (neither have been really pushed)
The HZ the guy had them at 860 CAS4 2.1v
Crucial was at 1111 Cas5 2.1v I think

Thanks
03-19-2009, 05:23 AM
lha

I took hell of lot all volts @ bios :D

1.43 vNB
3.2 vdimm
PL6
1:2 divider
BIOS version i think is 0901

Gonna do >700 mhz 4-4-4-4 some day :D
03-19-2009, 05:30 AM
CryptiK

Quote:

Originally Posted by lha

I took hell of lot all volts @ bios :D

1.43 vNB
3.2 vdimm
PL6
1:2 divider
BIOS version i think is 0901

Gonna do >700 mhz 4-4-4-4 some day :D

3.2v was that on dry ice or air? 5-4-4-4 is still great for 700 MHz.

I'm sitting here with ~1KG of dry ice and I cant use it as I have no insulation materials other than paper towel. I was trying to make a ghetto pot but I cant see it working without massive condensation issues and I don't want to risk killing the board.
03-19-2009, 05:33 AM
lha

Quote:

Originally Posted by CryptiK

3.2v was that on dry ice or air? 5-4-4-4 is still great for 700 MHz.

I'm sitting here with ~1KG of dry ice and I cant use it as I have no insulation materials other than paper towel. I was trying to make a ghetto pot but I cant see it working without massive condensation issues and I don't want to risk killing the board.

That was on air. 2x 120mm fans.
03-19-2009, 06:01 AM
CryptiK

3.2 on air is pretty crazy stuff, lucky your sticks are still alive heh.

I swapped to BIOS 1901 and 1:2 is working now. I took the cpuz SS then tried to run everest and it crashed unfortunately.

678 MHz CL5 @ 2.45v
http://i720.photobucket.com/albums/w...678mhz245v.jpg
03-19-2009, 06:44 AM
Ch@pS

Quote:

Originally Posted by CryptiK

3.2v was that on dry ice or air? 5-4-4-4 is still great for 700 MHz.

I'm sitting here with ~1KG of dry ice and I cant use it as I have no insulation materials other than paper towel. I was trying to make a ghetto pot but I cant see it working without massive condensation issues and I don't want to risk killing the board.

Easy solution, flour, or indeed make a paper pot, google eather of them and you're sorted. :)
03-19-2009, 11:18 AM
Shiranui Gen-An

Quote:

Originally Posted by zsamz_

i say 10% chance they are d9gkx i wouldnt touch em
saw them on this weeks sale $29.99 CAD after $20 MIR and i didnt look twice

Yeah, I wouldn't bet on the Firestix: http://www.biwa.ne.jp/~yok/FIRESTIX1...ESTIX1066.html
03-22-2009, 03:16 AM
Ket

Quote:

Originally Posted by lha

M2F isnt the best dual channel extreme ram mobo.

Actually, thats not quite true. The M2F just has a limited amount of modules it will work with, but the modules it will work with work across all DIMM banks, thats the sacrafice made, less modules compatible with the board in trade for the modules that are compatible working across all DIMM banks.
03-22-2009, 04:08 AM
CryptiK

Quote:

Originally Posted by Ket

Actually, thats not quite true. The M2F just has a limited amount of modules it will work with, but the modules it will work with work across all DIMM banks, thats the sacrafice made, less modules compatible with the board in trade for the modules that are compatible working across all DIMM banks.

I'm pretty sure he meant it's not a good ram overclocking board, which it isn't. AFAIK, he has the highest ram overclock on the M2F at 700 MHz CL5 followed by me at 678 MHz CL5.
03-22-2009, 05:45 AM
Ket

I wouldnt call 1400MHz a bad result out of DDR2 :p:
03-22-2009, 11:05 AM
Mafio

not so bad for an old DFI P35 UT with only 2.55 (real was around 2.52/2.53) of vdimm. :D

http://valid.canardpc.com/show_oc.php?id=532517

1280mhz cas4

WIP
03-22-2009, 11:43 AM
Ch@pS

Nicely done Mafio, you should try get us some bandwidth numbers at that speed. :)

Any maybe a screenie with subtimings etc. :D
03-22-2009, 12:16 PM
Mafio

http://valid.canardpc.com/show_oc.php?id=532578

1300 cas4 :D
03-22-2009, 02:45 PM
WaterFlex

Well done, Mafio :up:
03-23-2009, 06:29 AM
simone18

Quote:

Originally Posted by Mafio

http://valid.canardpc.com/show_oc.php?id=532578

1300 cas4 :D

hi mate. nice to see that you got 1300cas4 too :D

cellshock pc8000 cas4 @ 2.66v
http://valid.canardpc.com/cache/banner/532558.png

i'm wrong or you've given 2.65v?
03-23-2009, 07:52 AM
simone18

i've forgot the s-pi 1M screen:

http://forum.hwproject.net/imagehost...68d1a05eb5.jpg
03-23-2009, 10:18 AM
lha

Quote:

Originally Posted by simone18

i've forgot the s-pi 1M screen:

http://forum.hwproject.net/imagehost...68d1a05eb5.jpg

Why so high PL? and cant you push less tRFC? like 44 or 48. I did 1400mhz 5-4-4-4 PL6, but that was single channel.
03-23-2009, 10:48 AM
simone18

subtimings on auto. and the gigabyte ud3r doesn't like low PL...it's a bug of the board...with reasonable voltage i have to set PL8 to boot over 400mhz fsb :(
03-23-2009, 12:41 PM
Mafio

Quote:

Originally Posted by simone18

hi mate. nice to see that you got 1300cas4 too :D

cellshock pc8000 cas4 @ 2.66v
http://valid.canardpc.com/cache/banner/532558.png

i'm wrong or you've given 2.65v?

yes, 2.65

Quote:

Originally Posted by WaterFlex

Well done, Mafio :up:

thx :)
03-23-2009, 01:54 PM
Kean

My Crucial 10thAE: http://kean.sg-net.eu/OC/ae_600_4444_pl5.PNG
I know this results sucks but it was done along time ago on early MSI BIOS.
03-24-2009, 01:35 AM
simone18

nice PL5...if you still have the board, go for bios update :D
03-24-2009, 04:24 AM
radaja

well i got me another set of team group pc 10400's from memoryc.i knew it was a mistake to sell my first kit.they are just too good not to have.
03-24-2009, 04:25 AM
simone18

LOL. i think so ;)
03-24-2009, 05:23 AM
CryptiK

Quote:

Originally Posted by radaja

well i got me another set of team group pc 10400's from memoryc.i knew it was a mistake to sell my first kit.they are just too good not to have.

There's still plenty of fun to be had with D9's, especially with a board like yours.
03-24-2009, 06:28 AM
radaja

yep,thats why i got them.trying to sell my Q9650 and 2x2GB g.skill9600's so i can get a dual core for some high fsb d9 OC's with this board.much more fun to be had
03-24-2009, 07:15 AM
lha

Quote:

Originally Posted by Kean

My Crucial 10thAE: http://kean.sg-net.eu/OC/ae_600_4444_pl5.PNG
I know this results sucks but it was done along time ago on early MSI BIOS.

Pretty tight timings :up:
03-24-2009, 07:31 AM
Kean

Quote:

Originally Posted by lha

Pretty tight timings :up:

Quote:

Originally Posted by simone18

nice PL5...if you still have the board, go for bios update :D

thanks guys!
I don't have MSI already. Now I can try it on Biostar TPower I45.
03-24-2009, 06:27 PM
Ket

Quote:

Originally Posted by radaja

yep,thats why i got them.trying to sell my Q9650 and 2x2GB g.skill9600's so i can get a dual core for some high fsb d9 OC's with this board.much more fun to be had

Where do you live? I may be able to take those 9600s off your hands :D
03-25-2009, 06:20 AM
Ch@pS

Quote:

Originally Posted by radaja

yep,thats why i got them.trying to sell my Q9650 and 2x2GB g.skill9600's so i can get a dual core for some high fsb d9 OC's with this board.much more fun to be had

I'd take that Q9650 off your hands, and I've got a set of handpicked team Xtreem D9GMH 1300MHZ 4-4-4-3 stable on air if you're interested, let me know. :P
03-25-2009, 08:29 AM
Mafio

cellshock pc8000 on EP45 Extreme

http://valid.canardpc.com/show_oc.php?id=534346

1302.6 + mhz cas4 with 2.66volt :D
03-25-2009, 09:23 AM
Kean

wow it's insane :clap:
Can you run SPI 1M on it?
03-25-2009, 09:41 AM
Mafio

Quote:

Originally Posted by Kean

wow it's insane :clap:
Can you run SPI 1M on it?

i'm working on it:D
03-25-2009, 10:01 AM
simone18

go mate. i'm sure you'll do it ;)
03-25-2009, 10:02 AM
Mafio

http://forum.hwproject.net/imagehost...a6fe9868ba.jpg

super-pi 1m @1300 cas 4 with 2.66volt :D
03-25-2009, 10:53 AM
Kean

Quote:

Originally Posted by Mafio

super-pi 1m @1300 cas 4 with 2.66volt :D

That's what I was talking about!
Great job :clap: :up:

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 02:00 PM.

XtremeSystems