Dual Core Opteron Thread #2

Printable View

Show 100 post(s) from this thread on one page

09-28-2007, 04:05 PM
autobot

Well I tried out lowering my multiplier to 8, dropped down the ram divider to 133 and stability wise I topped out at 313 which of course is 2.5Ghz.
I dunno what the deal with that was until I thought that perhaps my memory was getting too high. I put everything back to my original settings and dropped the divider down to 133 instead of 166. Low and behold, that was the issue. My OCZ Platinum memory receiving 2.7v and at 3-3-3-8 doesn't really like to go over its stock speed of DDR400. I'm so far testing stable at2655Mhz with a load of 45c on core 1 and 42c on core 2.
I'll post again when I hit the wall again. :) Thank you!!!
09-28-2007, 04:51 PM
QuietIce

Quote:

Originally Posted by autobot

Well I tried out lowering my multiplier to 8, dropped down the ram divider to 133 and stability wise I topped out at 313 which of course is 2.5Ghz.
I dunno what the deal with that was until I thought that perhaps my memory was getting too high. I put everything back to my original settings and dropped the divider down to 133 instead of 166. Low and behold, that was the issue. My OCZ Platinum memory receiving 2.7v and at 3-3-3-8 doesn't really like to go over its stock speed of DDR400. I'm so far testing stable at2655Mhz with a load of 45c on core 1 and 42c on core 2.
I'll post again when I hit the wall again. :) Thank you!!!

Glad you figured it out! :)

Before I OC the whole system I always check out each part by itself; CPU, RAM, HT Link, and HTT - that way there's no surprises later ...
09-28-2007, 08:14 PM
autobot

Well, I hit the wall once again at 2789Mhz with a HTT of 310 at the stock 9x multiplier. I tell ya, this OCZ Platinum is really picky! It doesn't like running any faster than DDR400 speeds. Should I drop the memory divider once again (currently at 133) and try to up the HTT some more?
09-29-2007, 03:27 AM
QuietIce

Quote:

Originally Posted by autobot

Well, I hit the wall once again at 2789Mhz with a HTT of 310 at the stock 9x multiplier. I tell ya, this OCZ Platinum is really picky! It doesn't like running any faster than DDR400 speeds. Should I drop the memory divider once again (currently at 133) and try to up the HTT some more?

You bet!!! NOTHING is more important than CPU speed. I'd drop the RAM until you know what the top end on the CPU is going to be. After that you might want to adjust things but maybe not.

RAM speed is a distant second for OC'ing ...
09-29-2007, 12:52 PM
biohead

Ok guys, my 180 is now officially out of order. I'm giving this hobby a break until Phenom hits. I suddenly realized how much money I wasted on short term pleasures.
09-29-2007, 01:13 PM
Mord

Hey!

A little update here. I stripped her. Changed my whole watercooling setup to apogee gt, mcr320, 12mm ID tubing.
I am now priming at 3160MHz@1.43V real vcore (1.4*104%=1.456V)! Temp are low as 40-42. Screens tomorrow, gotta sleep.
09-30-2007, 05:43 AM
freakBYnature

Quote:

Originally Posted by QuietIce

You bet!!! NOTHING is more important than CPU speed. I'd drop the RAM until you know what the top end on the CPU is going to be. After that you might want to adjust things but maybe not.

RAM speed is a distant second for OC'ing ...

Are you serious? I have a couple of G.Skil PC4800 sticks running at 3-4-4-8 DDR600, along with a 3000+ venice @2.7 GHz... and you honestly say that if I had it running at DDR400 it wouldn't make "that much of a difference"? :D

I get it, you say that CPU speed matters more than RAM speed, but it doesen't on s939, it matters what both CPU and RAM is set at together :cool:

So, if you find out what your max cpu is, and the find out what your max mem is, you can make a controlled attempt at making them work at max together... and I tell you... I used a couple of weeks making my TCCD run at DDR600, damn picky those to, had to cool them actively aswell and run with a lower voltage on both cpu and ram then I thought... CPU 1.4V and RAM 2.7V @ 2.7 GHZ/DDR600 3-4-4-8 aint bad ;) Picky mem though... hate setting the memory!!! Takes forever!!!
09-30-2007, 06:03 AM
PhilDoc

Quote:

Originally Posted by freakBYnature

Are you serious? I have a couple of G.Skil PC4800 sticks running at 3-4-4-8 DDR600, along with a 3000+ venice @2.7 GHz... and you honestly say that if I had it running at DDR400 it wouldn't make "that much of a difference"? :D

I get it, you say that CPU speed matters more than RAM speed, but it doesen't on s939, it matters what both CPU and RAM is set at together :cool:

So, if you find out what your max cpu is, and the find out what your max mem is, you can make a controlled attempt at making them work at max together... and I tell you... I used a couple of weeks making my TCCD run at DDR600, damn picky those to, had to cool them actively aswell and run with a lower voltage on both cpu and ram then I thought... CPU 1.4V and RAM 2.7V @ 2.7 GHZ/DDR600 3-4-4-8 aint bad ;) Picky mem though... hate setting the memory!!! Takes forever!!!

You're absolutely right and btw, nice memory clocks. Cpu speed is important and should be maxed, but memory speed can make up for a lot. I'm supprised that you can't get more out of your OCZ platinum. I have the same memory and got DDR 560. OCZ guantees it at 2.8v so I'd up the voltage to 2.8 and then also give it the .3 in the bios. From looking around the forum the most this memory seems to like is 2.9v so I wouldn't go over that. If you haven't already then put a 120 mm fan blowing on the memory. You can lower your cpu clock temporally buy lowering your multi and set the memory at 200 divider. Use clock gen or A64 info to up the memory speed in windows and run something like spi 1M to check the increase. This way you can find the max memory setting.
09-30-2007, 07:13 AM
QuietIce

I had no intention of saying RAM wasn't important - of course it is. RAM should be run at the highest speed you can get it but not at the cost of a lot of CPU speed. Given a choice between a CPU @ 3.0 GHz & RAM @ 220 MHz OR CPU @ 2.8 GHz & RAM @ 250 MHz which would you pick? I'd trade off at 1:4 or even 1:3 maybe but not much less. 100 MHz less on the CPU for a 300 MHz RAM increase is a fair trade but I think you'll find anything less to be a backward step.

The thread is a little old but most of it is still good procedure and a great guide for beginners: http://www.ocforums.com/showthread.php?t=391768
09-30-2007, 12:15 PM
freakBYnature

Quote:

Originally Posted by QuietIce

100 MHz less on the CPU for a 300 MHz RAM increase is a fair trade but I think you'll find anything less to be a backward step.

Agreed! 100 MHz is excactly what I had to trade off the 3000+ to get the G.Skill to settle at 300 MHz, but hey then again I was able to set it at 2.7 GHz at 0.1V less then what I had to set it at 2.8 GHz (2.7 GHz @ 1.4V & 2.8 GHz @ 1.5V), so I am very pleased :D
10-01-2007, 03:05 AM
Mord

OK, guys, BIG confusion here!

Temps of system are beautiful - max: 45C chipset, 49C mosfets, open air build.
CPU Temperatures and Scaling (orthos stable):
~3000GHz@1.35V 35-36C
3060GHZ@1.35V x 104% 37-38C
3100GHZ@1.375V x 104% 38C
3160GHz@1.4V x 104% 39-40C
3170+ NO GO even at 1.65V !!! 46C Orthos fails in 1-10mins

Tried already:
swapping to 2x256MB BH5's (mine is UCCC 2x1GB);
More powerful PSU - Tagan 580-U22
Upped the volts on LDT, Chipset, DRAM, PCIE freq
Lowered the HTT multy, DRAM divider, loosened timings

Only things I see left are: 2T on ram, moving on the orange slots, changing bioses (704-2BTA now, should I?)...

Help, help, help... :(
10-01-2007, 04:43 AM
biohead

loosened max async latency (MAL) and read preamble (RP) ?
10-01-2007, 08:14 AM
Cheffy

might just be the limit. - it can come on very suddenly
2966 @ 1.425
2978 @ 1.5
3000 @ 1.55
3100 @ 1.65
3150ish @ 1.725
3200 @ suicide only
10-01-2007, 08:50 AM
Lastviking

Quote:

Originally Posted by Mord

OK, guys, BIG confusion here!

Temps of system are beautiful - max: 45C chipset, 49C mosfets, open air build.
CPU Temperatures and Scaling (orthos stable):
~3000GHz@1.35V 35-36C
3060GHZ@1.35V x 104% 37-38C
3100GHZ@1.375V x 104% 38C
3160GHz@1.4V x 104% 39-40C
3170+ NO GO even at 1.65V !!! 46C Orthos fails in 1-10mins

Tried already:
swapping to 2x256MB BH5's (mine is UCCC 2x1GB);
More powerful PSU - Tagan 580-U22
Upped the volts on LDT, Chipset, DRAM, PCIE freq
Lowered the HTT multy, DRAM divider, loosened timings

Only things I see left are: 2T on ram, moving on the orange slots, changing bioses (704-2BTA now, should I?)...

Help, help, help... :(

Send it to me so i can test it ^^ :)

But i think the trouble is something like this "loosened max async latency (MAL) and read preamble (RP) ?"
10-01-2007, 01:40 PM
QuietIce

You may have hit the top end of the "FSB" - you're already over 350. Have you checked it by itself ...?
10-01-2007, 10:15 PM
Mord

MAL doesn't boot at more than 12-13. Works fine at 9. RP is 6, anything more than 7.5 - no boot. :(

I'm really frustrated now. There is something I am missing. Also QietIce, do you really believe 350HTT is max for the Ultra-D?! I say this is heresy. :p:

Again - why do I think it's not the HTT - upped the volts of LDT and chipset with one step, lowered the HTT multy to 2.

Tonight I am going 8x400HTT, just to be sure.

Thanks for the help for now. More suggestions welcomed.

Abyss
10-01-2007, 10:48 PM
turbox997

Quote:

Originally Posted by biohead

Ok guys, my 180 is now officially out of order. I'm giving this hobby a break until Phenom hits. I suddenly realized how much money I wasted on short term pleasures.

what'dya mean? out of order? Did it die? And i know what you mean about the money and short term pleasures. :shakes:

I'm always tempted to order a new cpu/gpu or even a new rig(whole darn thing, new platform, new mobo, etc.) for just incremental gains..just to know i have something better than before and the best of what it is(best stepping).

I'm trying to make a new policy for myself in which, I won't upgrade unless the new system(cpu) will give me gains by leaps and bounds, that way I can maybe live with my computer for 2 years+ or so before doing it again.
10-02-2007, 02:35 AM
QuietIce

Quote:

Originally Posted by Mord

Also QuietIce, do you really believe 350HTT is max for the Ultra-D?! I say this is heresy. :p:

I looked at your board before posting and thought the same thing but you never know. ASUS changed the A8N32 in the middle (Rev 'g' :rolleyes:) and it doesn't do near the 350-380 I get out of the "old" A8N32s. It was just a WAG, easy and quick enough to check if you haven't recently. :shrug:

BTW: Even upping the chipset voltage only buys me 5-10 MHz on my A8N32s - they've either got it or they don't. I figure the DFI's are the same, I mean it IS the same chipset and both are great manufacturers ...
10-02-2007, 08:32 AM
RVWinkle

Quote:

Originally Posted by Mord

Temps of system are beautiful - max: 45C chipset, 49C mosfets, open air build.
CPU Temperatures and Scaling (orthos stable):
~3000GHz@1.35V 35-36C
3060GHZ@1.35V x 104% 37-38C
3100GHZ@1.375V x 104% 38C
3160GHz@1.4V x 104% 39-40C
3170+ NO GO even at 1.65V !!! 46C Orthos fails in 1-10mins

Nice chip you have there, after correcting my memory timings I'm sitting in a similar situation where it fails Orthos at 3.2ghz no matter what. I'm still looking for that magic setting to make it stable.
10-02-2007, 09:54 PM
Mord

Quote:

Originally Posted by RVWinkle

I'm sitting in a similar situation where it fails Orthos at 3.2ghz no matter what.

That, my friend, made me cry all night long. :(

I AM POSITIVE, there is something wrong in my methods. This chip HAS to go 3200-3250MHz, orthos stable with very little voltage. Just can't find what's holding me back. And don't have much time - my contest is on saturday. Damn time!

Think! Think! :brick:
10-03-2007, 01:34 AM
QuietIce

Quote:

Originally Posted by Mord

That, my friend, made me cry all night long. :(

I AM POSITIVE, there is something wrong in my methods. This chip HAS to go 3200-3250MHz, orthos stable with very little voltage. Just can't find what's holding me back. And don't have much time - my contest is on saturday. Damn time!

Think! Think! :brick:

Are you already on water?

Have you de-lidded?
10-03-2007, 02:40 AM
by -=Merlin=-

my new test with new bios

http://merlin.slang-in-use.de/Fotos/1.gif
http://merlin.slang-in-use.de/Fotos/2.gif
10-03-2007, 05:01 AM
Mord

Yep and yep again!

Here's a pic of the setup:
http://img518.imageshack.us/img518/455/dsc00290oz3.jpg
http://img72.imageshack.us/img72/3220/dsc00308jk6.jpg
http://img530.imageshack.us/img530/5889/dsc00424ny8.jpg
10-03-2007, 01:50 PM
QuietIce

Then the only left I can think of are bigger fans - these work well on a controller for "everyday": http://www.sidewindercomputers.com/de12trblhisp.html
10-03-2007, 10:44 PM
Mord

Hm, I don't get it.

Why is the big fan? I am even now runnig all of them quiet at 1000rpm. No temp issues. Is i ran them at max then all temps drop under 40C even sub 36C. So no prob with that.

Also ran 8x390 with no extra Vchipset or LDT and no problems. So not the board or HTT...
I'm taking this baby to hell with 1.7V. If it is not stable I'm going chilled tomorrow, although 36C load with 1.65V is almost as chilled water...

Show 100 post(s) from this thread on one page