So after 48 hours with this mobo, I'm VERY stable at 4.1 GHz:
http://i383.photobucket.com/albums/o...reenOrthos.jpg
But I should be able to run these LV Blades much faster. What do I need to do about my other options (skews, etc...)?
I did modify the sinkshttp://i383.photobucket.com/albums/o...n/IMG_0921.jpg
I was impressed by their impressions (nice contact) http://i383.photobucket.com/albums/o...n/IMG_0919.jpg
Im BaCK :)
I did the bios temp HOSS331 recommended , wow my system responding much better , very smooth ... good looking out dude. now the bad news im priming pass 7 hours actual did 9 according to results sheet , but pc did ultimately crash , where should i go from here to figure out , i pretty good at oc but ive never seen a system crash so far along so it makes it that much harder , should i just try again and see if maybe it was just a glitch , thanks again for everyone's help ;)
Code:******Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.05GHz...........................[ 450 x 9.0]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 450 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400 ]
System Memory Multipler.........................[ 2.00D ]
Memory Frequency 1066...........................[ 900 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 4 ]
tRCD............................................[ 4 ]
tRP.............................................[ 4 ]
tRAS............................................[ 12 ]
******Advanced Timing Control******
tRRD[3].........................................[ 3 ]
tWTR[3].........................................[ 3 ]
tWR[6]..........................................[ 6 ]
tRFC[54]........................................[ 52 ]
tRTP[3].........................................[ 3 ]
Command Rate (cmd)[0]...........................[ 2T ]
******Channel A Timing Settings******
Static tRead Value [ 8 ] ................[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 8 ] ................[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.15 ]...................[ 1.38875 ]
CPU Termination [ 1.20 ]...................[ 1.280 ]
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.760 ]...................[ 0.835 ]
MCH Core [ 1.100 ]...................[ 1.300 ]
MCH Reference [ 0.760 ]...................[ 0.850 ]
MCH/DRAM Refernce [ 0.900 ]...................[ 1.000 ]
ICH I/O [ 1.500 ]...................[ 1.500 ]
ICH Core [ 1.100 ]...................[ 1.100 ]
DRAM Voltage [ 1.800 ]...................[ 2.100 ]
DRAM Termination [ 0.900 ]...................[ 1.000 ]
Channel A Ref [ 0.900 ]...................[ 1.000 ]
Channel B Ref [ 0.900 ]...................[ 1.000 ]
******Advanced BIOS Features******
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
Try this one.Quote:
Originally Posted by the_real_7
Code:******Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.05GHz...........................[ 450 x 9.0]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 450 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400 ]
System Memory Multipler.........................[ 2.00D ]
Memory Frequency 1066...........................[ 900 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 4 ]
tRCD............................................[ 4 ]
tRP.............................................[ 4 ]
tRAS............................................[ 12 ]
******Advanced Timing Control******
tRRD[3].........................................[ 3 ]
tWTR[3].........................................[ 3 ]
tWR[6]..........................................[ 6 ]
tRFC[54]........................................[ 52 ]
tRTP[3].........................................[ 3 ]
Command Rate (cmd)[0]...........................[ 2T ]
******Channel A Timing Settings******
Static tRead Value [ 8 ] ................[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ 1066 ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 8 ] ................[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ 1066 ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.15 ]...................[ 1.37500 ]
CPU Termination [ 1.20 ]...................[ 1.280 ]
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.760 ]...................[ 0.835 ]
MCH Core [ 1.100 ]...................[ 1.280 ]
MCH Reference [ 0.760 ]...................[ 0.850 ]
MCH/DRAM Refernce [ 0.900 ]...................[ 1.050 ]
ICH I/O [ 1.500 ]...................[ 1.500 ]
ICH Core [ 1.100 ]...................[ 1.100 ]
DRAM Voltage [ 1.800 ]...................[ 2.100 ]
DRAM Termination [ 0.900 ]...................[ 1.050 ]
Channel A Ref [ 0.900 ]...................[ 1.050 ]
Channel B Ref [ 0.900 ]...................[ 1.050 ]
******Advanced BIOS Features******
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
Hey guys. My 4.05Ghz run is 100% stable (which i am happy with as a 24/7 clock) but what i cant understand is i am running 333 and 2.40b. If i choose any other strap it will just get stuck in a boot loop. Even 333 and 2.00b wont work.
I tried every combo and the one i am using now is the only one that will boot.
Has anyone had a similar experience?
Thanks
Did you change the "Static tRead Value" under Channel A + B Timing Settings?
With 333 and 2.0B, you'll have to change it to 9 or 10. It wouldn't boot on my rig my rig either if I left it at 8.
With 333 strap and 2.40B, I can change the option to 8 and it will boot with no problems.
What bios are you on? I had the same strap problem with bios f8, after upgrade to f9 the problem went away.Quote:
Originally Posted by jonathankru
:with: I totally forgot to try higher PL.Quote:
Originally Posted by Jupiler
Will retry now. Thanks for the quick reply.
im running my q9450@3.5ghz with 1.16v is anyone getting the same volts or is mine to low/high its stable even with intel burn test so far but i think it will hit about 70c
with prime i think it will hit about 62-mayme 64c MAX is that going to be safe for 24-7 use or do you think i shuld back the speed or im i ok
thanks guys
I would say the voltage is safe and i am sure the temps are OK since Intel burntest does make cpu`s allot hotter then they would under any normal pc use.Quote:
Originally Posted by rubber5
Maybe you should consider upgrading your cpu cooler?
i have a thermalright extreme 120 with silenx 120mm fan the 90cfm one on a fan controller on low becuse it doesnt make much difference on highQuote:
Originally Posted by jonathankru
i have been running prime (small fft's) for about 30mins to get a rugh idea and the fan on low it goes to 60c on high its goes to 58c.
2c is not much concidering the difference in speed of the fan if you know what i meen
can you recomend any fans what ARE better thats not to noisy
thanks for the reply
What temp is your room?Quote:
Originally Posted by rubber5
What thermal paste are you using?
I am sure your temps should be lower, Also how are you measuring your temps?
the temp in my room is about 26cQuote:
Originally Posted by jonathankru
im using artic silver 5 paste
and im using realtemp 2.7 + have used realtemp 3.0
i cant understand it i thught i would be getting lower temps to but nothing works
i have even re-seted the cooler and it doesnt change
i happy someone is trying to help me thanks again
I got slight problem here. I got e6320 and ud3p. I am able to hit 470 with a 1 .35 - .37 vcore stable. Everything over 470 with no mather what vcore it doesnt post. 471 no and so forth. I did try using set fsb in windows and put 1.5 and 1.55 vcorein bios and rise my nb vcore but as soon as I apply for 471 in crashes.
Any ides?
Quote:
Originally Posted by rubber5
TRUE 120 .. needs lapping ... the base is verry bad usually. also works best with two fan's with high rpm ...
if u wan't sillence and performance then Cooler Master Z600 or Scythe Mugen 2 is the way ... Scythe has the best base of the two coolers so the contact is verry good. Z600 is verry good also has bigger surface for heat disipation.
it might be your memory is geting overclocked to much what speed and latency is your memoryQuote:
Originally Posted by dpokrajac0
which one would you say is the best out of all of themQuote:
Originally Posted by kagula323
Sorry i missed your reply. I am currently on F9 final release bios now.Quote:
Originally Posted by OC_Newbee
i have managed to get 400 and 2.00D to boot with pl of 9 and 10(currently testing 10 only) but i cant get prime 95 to run for more then 4 minutes before one thread fails.
I have been messing with different MCH voltages and MCH/DRAM References.
I have found that 1.36 NB to be the best so far (any higher and it still crashes at the same point)
What else can i change to try help stabilize my ram?
I have taken 1 Pair of ram out so i think i am definitely missing something here.
http://i44.tinypic.com/11jyxwg.jpghttp://i44.tinypic.com/2v8pz5y.jpg
I am running at 940 linked to 1:1. They are corsair dominators 1066 @ 5-7-7-24Quote:
Originally Posted by rubber5
to be honnest im not sure why thats hapining im new to overclocking so i dont really knowQuote:
Originally Posted by dpokrajac0
the only thing i can say is try setting the latencys to outo but not the mhz and see what happens
the best is TRUE120 extreme ... but only after u lapp the base (it is quite a lot of work to do and only if u use two high rpm fans with good static presure in push pull) ... after that Mugen 2 (no need for lap and good fixing system) ... and then verry close comes z600 :).
I now have a Mugen 2 on my CPU and before that I had a true 120 ultra but didn't wanted to lapp after finding it only works best with high rpm fans (I still have it ... sits in my Mugen 2 BOX :D waitting for a new owner). I tested also Z600 but it cooled badder than Mugen 2 with about 4-5 degrees C and is verry big and heavy :| ... one thing I didn't liked about it.
Mugen 2 is really nice. Cools much better than TRUE120 unlapped and the contact with the IHS of the processor is great. The difference between MUGEN2 default base and TRUE120 unlapped with the same Noctua 1200RPM was for me of about 10 degrees in favor of the Mugen2.
Put on top of that the fact that comes with it's own fan Schyte @1200 RPM (fairly sillent) and also includes LGA 1336 retention kit + the best price between the three of these coolers and I think u found yourself the best cpu cooler :P
(Z600 comes without a fan but newer ones come with lga1336 retention)
I say go for the Mugen 2 if u want strong performance and silence or lapp that TRUE and get 2 high rpm fans if u wannt best cooling performance.
Edit: Another worth to mention cooler would be Megahalems (that is known now like "the TRUE killer" but has a verry big price and it's hard to find for the moment).
Myself ... I'm verry satisfied with my Mugen2 with 2 NOCTUA 1200rpm cooler in push-pull configuration. Keeps my E8400 1.25vid E0 @ 4500 1.39375V in bios (1.36 @ LOAD) under 65C (arround 62-63C) and that's in a room without air conditioner. (But the case is an Antec 1200 ... so airflow is also verry good).
PS : sorry for my bad english ... I'm from Romania.
ok thanks for that but i think i might just not bother overclocking since it shows no benifit so far in gamesQuote:
Originally Posted by kagula323
but if you dont mind can you tell me where i can get the things i need to lap my cpu cooler as i dont know what to use or were to get it
THANK YOU
Quote:
Originally Posted by jonathankru
Set in bios cpu termination 1.2, CPU ref between 0,800 - 0850 (from what i've read so far this is what quad's like), Mch core 1.36 should be right, MCH reference set it at 0.700 and then set cpu termination back @ 1.38. CPU reference and mch reference will scale automatically with the cpu termination.
Try this and tell us how it goes.
Also in Advanced Settings:
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Try this and tell us how it goes.
I guess I will try by trial/error thing.Quote:
Originally Posted by rubber5
I have tp45hp also and will try in that mobo too.
I'm sure on the cooling section u can find a thread about lapping. I'm not in the measure to give this kind of advice. I didn't wanted to lapp. Search for a thread of this kind and read. It will give u more info and help than I would be able to.Quote:
Originally Posted by rubber5
Going to sleep now.. must go to work after about 7 hours from now :).
Hope my advices will help.:up:
IT HAS THANKS A LOT :)Quote:
Originally Posted by kagula323