EP45-UD3P

Printable View

Show 100 post(s) from this thread on one page

05-10-2009, 12:53 AM
coop

Finally after several hrs. of Pi, I was able to get under 10.09.000. I did need to raise vcore but was able to lower MCH. Also ran PCI-e freq. @101. Idk if that mattered. I tried for a long time to do lower vcore, but that was not happening.
[IMG]http://img12.imageshack.us/img12/5737/32m4807f.jpg[/IMG]

Code:

MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto CPU Clock Ratio .......................: 9 Fine CPU Clock Ratio...................: 0.5 CPU Frequency .........................: 4.807GHz (506X9.5) Clock Chip Control Standard Clock Control CPU Host Clock Control.................: [Enabled] CPU Host Frequency (Mhz) ..............: 506 PCI Express Frequency (Mhz) ...........: 101 C.I.A.2 ...............................: [Disabled] Advanced Clock Control CPU Clock Drive........................: 900 PCI Express Clock Drive................: 1000 CPU Clock Skew (ps)....................: 50ps MCH Clock Skew (ps)....................: 100ps DRAM Performance Control Performance Enhance....................: Turbo Extreme Memory Profile (X.M.P.)........: Disabled (G)MCH Frequency Latch.................: 333MHz System Memory Multiplier ..............: 2.40D Memory Frequency (Mhz) ................: 1214MHz DRAM Timing Selectable ................: Manual Standard Timing Control CAS Latency Time.......................: 5 tRCD ..................................: 5 tRP'...................................: 5 tRAS...................................: 15 Advanced Timing Control Everything In Advanced Timing Control on auto. but tRFC 56 and Drive Strength Profiles OC-1200 DDR Write Training: Disable Motherboard Voltage Control CPU Load-Line Calibration..................: [Disabled] CPU Vcore..............................: 1.4375V CPU Termination........................: 1.36V CPU PLL................................: 1.61V CPU Reference..........................: 0.901 MCH/ICH MCH Core...............................: 1.40V Reference..............................: 0.801 MCH/DRAM Ref...........................: 1.13v ICH I/O................................: 1.5V ICH Core...............................: 1.100V DRAM DRAM Voltage...........................: 2.26v DRAM Termination ......................: Auto Channel A Reference....................: Auto Channel B Reference ...................: Auto
05-10-2009, 01:49 AM
D-an-W

Has anyone with a E8400 & UD3P combo had trouble getting over 449FSB?

I can run 449x9 all day long (I have a TrUE on order to reduce temps further) but 450FSB eludes me so far.

Template used for 449FSB...

Code:

************************************* ************************************* Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9 ************************************* ************************************* ****************************** MB Intelligent Tweaker(M.I.T.) ****************************** Robust Graphics Booster ..............: [Fast] CPU Clock Ratio ......................: [9X] x Fine CPU Clock Ratio................: +0.0 CPU Frequency ........................: 4.04GHz( 449x9) ********** Clock Chip Control ******** >>>>> Standard Clock Control CPU Host Clock Control................: [Enabled] x CPU Host Frequency(Mhz).............: [449] PCI Express Frequency(Mhz)............: [100] C.I.A.2...............................: [Disabled] >>>>> Advanced Clock Control..........: [Press Enter] CPU Clock Drive.......................: [800mV] PCI Express Clock Drive...............: [900mV] CPU Clock Skew........................: [ 0ps] MCH Clock Skew........................: [ 0ps] ******** DRAM Performance Control ******** Performance Enhance...................: [Standard] Extreme Memory Profile(X.M.P.)........: [Disabled] (G)MCH Frequency Latch................: [Auto] System Memory Multiplier (SPD)........: [2.00D] Memory Frequency(Mhz).....800.........: 900 DRAM Timing Selectable (SPD)..........: [Manual] >>>>> Standard Timing Control x CAS Latency Time................5...: [ 5] x tRCD ...........................5...: [ 4] x tRP.............................5...: [ 4] x tRAS...........................18...: [12] >>>>> Advanced Timing Control.........: [Press Enter] x tRRD............................3...: [ 3] x tWTR............................3...: [ 4] x tWR.............................6...: [ 6] x tRFC...........................52...: [54] x tRTP............................3...: [ 3] x Command Rate (CMD) .............0...: [ 2] >>>>> Channel A Timing Settings.......: [Press Enter] x Static tRead Value.............10...: [ 9] x tRD Phase0 Adjustment...........0...: Auto x tRD Phase1 Adjustment...........0...: Auto x tRD Phase2 Adjustment ..........0...: Auto x tRD Phase3 Adjustment...........0...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel A Driving Settings......: [Press Enter] x Driving Strength Profile............: [1066MHz] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto >>>>> Channel B Timing Settings.......: [Press Enter] x Static tRead Value.............10...: [ 9] x tRD Phase0 Adjustment...........0...: Auto x tRD Phase1 Adjustment...........0...: Auto x tRD Phase2 Adjustment ..........0...: Auto x tRD Phase3 Adjustment...........0...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel B Driving Settings......: [Press Enter] x Driving Strength Profile............: [1066MHz] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto ****** Motherboard Voltage Control ****** Voltage Types..........Normal...........Current ----------------------------------------------- >>> CPU Load-Line Calibration.................: [Enabled] CPU Vcore..............1.27500V.......: [1.39375V] CPU Termination........1.200V.........: [1.300V] CPU PLL................1.500V.........: [1.570V] CPU Reference..........0.760V.........: [Auto] >>> MCH/ICH MCH Core...............1.100V.........: [1.240V] MCH Reference..........0.760V.........: [Auto] MCH/DRAM Reference.....0.900V.........: [Auto] ICH I/O................1.500V.........: [1.570V] ICH Core...............1.100V.........: [1.200V] >>> DRAM DRAM Voltage...........1.800V.........: [2.080V] DRAM Termination.......0.900V.........: [Auto] Channel A Reference....0.900V.........: [Auto] Channel B Reference....0.900V.........: [Auto] ******** Advanced BIOS Features ******** Hard Disk Boot Priority...............: [Press Enter] First Boot Device.....................: [USB-HDD] Second Boot Device....................: [Hard Disk] Third Boot Device.....................: [CDROM] Password Check........................: [Setup] HDD S.M.A.R.T. Capability.............: [Enabled] Limit CPUID Max. to 3.................: [Disabled] No-Execute Memory Protect.............: [Enabled] CPU Enhanced Halt (C1E)...............: [Disabled] C2/C2E State Support..................: [Disabled] x C4/C4E State Support................: Disabled CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.....................: [Disabled] Virtualization Technology.............: [Disabled] Delay For HDD (Secs)..................: [ 0] Full Screen LOGO Show.................: [Disabled] Init Display First....................: [PEG] ******** Integrated Peripherals ******** USB Keyboard Function.................: [Enabled] USB Mouse Function....................: [Enabled] USB Storage Function..................: [Disabled]
05-10-2009, 02:24 AM
kagula323

Quote:

Originally Posted by pangingIII

if anyone interested, this's how my bios (voltage section) is done.
i've been using this method with most of my overclocks since i use DDR2 version of the board (EP45-UD3R)

http://img7.imageshack.us/img7/91/50075cmos2.jpg

i hope i didn't make any mistake on the picture.

as for my E8400's, i used to adjust MCH ref. (NB GTL_ref.) values as follow....
400-450fsb.... 0.74
467fsb up.... 0.72
480fsb up.... 0.70
500fsb up.... 0.70, 0.68
600fsb.... 0.65/0.64

hope this helps.

what CPU voltage, MCH voltage and cpu skew's u used? for 600fsb?

can u post a template of one of your stable E8400 600FSB overclock? that would help a lot to me :)
05-10-2009, 02:55 AM
pangingIII

Quote:

Originally Posted by kagula323

what CPU voltage, MCH voltage and cpu skew's u used? for 600fsb?

can u post a template of one of your stable E8400 600FSB overclock? that would help a lot to me :)

what kind of stable overclocks are you expecting to get at 600fsb?
reason i ask because i never do much at high fsb.
05-10-2009, 03:37 AM
kagula323

Quote:

Originally Posted by pangingIII

what kind of stable overclocks are you expecting to get at 600fsb?
reason i ask because i never do much at high fsb.

I'm currently at 4500 9x500 with 1.39375 cpu, 1.32 cpu term, 1.57 pll, 1.34 mhc, 0.68mhc ref.
I think about 4200MHZ would be fine(600x7). Getting to 4500mhz (600x7.5) I believe it would require too much voltage increment and it's not worth the trouble.

What voltages/settings do u suggest I should try?
Well not sure if I'm going to take 600fsb for daily use ... but more for the fun of seeing what my cpu is able to do. :D

EDIT : system specs are: EP45-UD3P, E8400 E0 vid 1.25 under Scythe Mugen 2, 2GB(2x1) Patriot Viper 1200mhz (Elpyda chips :( no d9 for me),Leadtek GTX 260 896MB, Cooler Master Real Power 700W, Antec 1200
05-10-2009, 05:29 AM
D-an-W

kagula323, any chance of your full BIOS template please so I can see where I might be going wrong (Mine is 3 posts up)?
05-10-2009, 06:07 AM
Eeky NoX

I repeat that I'm now testing the DDR3 version and going forward to Leeghoofd's I4's conclusions !
Is there anything expecting there ? Ask me and I'll throw feedback pleasantly m8tes ;)

Goin' to F7 this week ...than I'll also check my CPUs under dice as soon as possible, but 600FSB is a long story I think :/ (even with the E8600 +F6 bios)

My D9s react strangely and I can't find any help anywhere :( (no other DDR3 modules anyway -_- )
05-10-2009, 07:30 AM
DOM.

Has anyone used a P4 Cpu in there mobo ?

mine only lets me push 1.4v to it like WTF ??

im on bios F9
05-10-2009, 07:55 AM
Ghostleader

Quote:

Originally Posted by radaja

thanks for the response:up:.the UD3P ddr3 is on the because of pangingIII's results.but i'll be using a dual core so thats why i might get the RE.i hear it great with a dual.

If you gonna run dual, RE is a good choice indeed and as pangingIII wrote "most important, seems to be, to find ram kits that can work well with the board", I agree, it seem like LGA775 DDR3 board is a bit picky about what ram to choose, do some reading before buy ram.

Quote:

Originally Posted by pangingIII

Hi Ghostleader, thanks.
DDR3 one is very similar to the DDR2 one, i just need to spend some time with it, and most important, seems to be, to find ram kits that can work well with the board, and if you already have a good overclocking CPU, then i would say you cant really go wrong with these boards. these boards (UD3P/R's, both DDR2 and DDR3 versions) are probably not the best boards for every needs, but so far to me, they are quite good boards. this's an opinion from just another user.

Thanks for your opinion, I might get a EP45T and see what it can do compare to my RE.

What ram do you have that work well with your board?
05-10-2009, 08:15 AM
radaja

thanks for the input Ghostleader,i'll research the ram carefully
05-10-2009, 08:35 AM
pangingIII

Quote:

Originally Posted by Ghostleader

Thanks for your opinion, I might get a EP45T and see what it can do compare to my RE.

What ram do you have that work well with your board?

right now i use crucial value 2x2GB's DDR3-1333 CAS9-9-9 D9JNM 1.5v,
2x2GB OCZ Flex EX DDR3-2000,
and 2x1GB Crucial Ballistix DDR3-2000 2.0v. but the crucial value ones are best.
i also have a few friends who also uses EP45T's and they are now using Crucial value 2x1GB DDR3-1333 CAS9-9-9 D9JNM 1.5v (actually, they bought the one that are 3x1GB kits),
these Crucial value kits are overclocking well and are working best on the boards and are so cheap.

radaja, if you decide to try the EP45T's, also try the crucial value that i use... 2x2GB's DDR3-1333 CAS9-9-9 D9JNM 1.5v they are very cheap but works best.
05-10-2009, 09:14 AM
kagula323

pangingIII u forgot about me ... I just need some starting lines for 600 FSB testing ... :(
05-10-2009, 09:27 AM
radaja

thanks pangingIII for the great info
are these the ones?
http://www.newegg.com/Product/Produc...82E16820148247
05-10-2009, 10:20 AM
kagula323

Quote:

Originally Posted by D-an-W

kagula323, any chance of your full BIOS template please so I can see where I might be going wrong (Mine is 3 posts up)?

Here u are :)

Quote:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
Fine CPU Clock Ratio...................: 0.0
CPU Frequency .........................: 4.50GHz (500X9)

Clock Chip Control

Standard Clock Control

CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 500
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]

Advanced Clock Control

CPU Clock Drive........................: 800
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)....................: 0

DRAM Performance Control

Performance Enhance....................: Turbo
Extreme Memory Profile (X.M.P.)........: Disabled
(G)MCH Frequency Latch.................: 333MHz
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ................: 1200MHz

DRAM Timing Selectable ................: Manual

Standard Timing Control

CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15

Advanced Timing Control

Everything In Advanced Timing Control on auto.
but tRas 9 and Drive Strength Profiles OC-1200

Motherboard Voltage Control

CPU

Load-Line Calibration..................: [Disabled]
CPU Vcore..............................: 1.39375V
CPU Termination........................: 1.32V
CPU PLL................................: 1.50V
CPU Reference..........................: Normal

MCH/ICH

MCH Core...............................: 1.34 or 1.38V
Reference..............................: 0.756
MCH/DRAM Ref...........................: Normal
ICH I/O................................: Normal
ICH Core...............................: Normal

DRAM
DRAM Voltage...........................: 2.32v [set this acording to your ram]
DRAM Termination ......................: Normal
Channel A Reference....................: Normal
Channel B Reference ...................: Normal
05-10-2009, 10:31 AM
pangingIII

Quote:

Originally Posted by radaja

thanks pangingIII for the great info
are these the ones?
http://www.newegg.com/Product/Produc...82E16820148247

mine are this one
CT25664BA1339.168FD's...
http://www.crucial.com/store/partspe...KIT25664BA1339

it seems like it's supposed to be this one at newegg...
http://www.newegg.com/Product/Produc...82E16820148262

Quote:

Originally Posted by kagula323

pangingIII u forgot about me ... I just need some starting lines for 600 FSB testing ... :(

sorry i'm thinking... what's the best suggestion to get you to 600fsb?
if you just want to boot at 600fsb you could try setting every values at the voltage section of the bios to Auto, and see if you can boot into Windows? please try this first.
05-10-2009, 11:15 AM
DOM.

Quote:

Originally Posted by kagula323

pangingIII u forgot about me ... I just need some starting lines for 600 FSB testing ... :(

Advanced Clock Control

CPU Clock Drive........................: 800
PCI Express Clock Drive................: 800
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)....................: 50

Motherboard Voltage Control

CPU

Load-Line Calibration..................: [Enabled]
CPU Vcore..............................: 1.39375V
CPU Termination........................: 1.34V
CPU PLL................................: 1.50V
CPU Reference..........................: 0.903

MCH/ICH

MCH Core...............................: 1.36V
Reference..............................: 0.788
MCH/DRAM Ref...........................: Normal
ICH I/O................................: Normal
ICH Core...............................: Normal
05-10-2009, 04:01 PM
Hoss331

Just doing a little testing on the new water setup. Im probably going to pop the Q9650 back in soon to see how it likes it since it was a hot head to begin with.

http://i131.photobucket.com/albums/p...mapImage2h.jpg
05-10-2009, 10:08 PM
coop

Quicker with less. I'm cool with this, time to move on.
[IMG]http://img15.imageshack.us/img15/468...807fastest.jpg[/IMG]
05-11-2009, 04:03 AM
radaja

well i got 2 kits of this ram in a trade and next week i'll be getting the ddr3 variant of the UD3P,and was wondering if anyone has tried
this ram with the board?im hoping it will work,if not i'll sell them and get a different kit.i just couldnt pass up the deal for these.so if anyone has used these together maybe you could let me know how they worked.
http://www.zipzoomfly.com/jsp/Produc...odlist=froogle
thanks
05-11-2009, 05:58 AM
ACK

Do you think is this board with an E8500 E0 capable to run a 24/7 system with the following specs?

FSB: 449*9.5=4264Ghz (1066*4)
RAM running at 1066Mhz 5-5-5-15 (Kingston HyperX or Crucial Balistix Tracer I have now both pair of modules)
EIST disabled

Cooled by a TRUE & a 120mm FAN into an Antec P182 case.

--------------------------------------------------------

:confused:
--------------------------------------------------------
I expect will be my next rig in a couple of weeks :yepp:

Thanks in advance :up:
05-11-2009, 07:26 AM
gergregg

Quote:

Originally Posted by ACK

Do you think is this board with an E8500 E0 capable to run a 24/7 system with the following specs?

FSB: 449*9.5=4264Ghz (1066*4)
RAM running at 1066Mhz 5-5-5-15 (Kingston HyperX or Crucial Balistix Tracer I have now both pair of modules)
EIST disabled

Should not be a problem.
05-11-2009, 03:16 PM
bluestang

Anyone running Kingston HyperX DDR2-1150 or DDR2-1200 2x1 GB kits? If so, I'm looking for help with BIOS settings. System specs in my sig. Thanks!!!
05-12-2009, 01:45 AM
rubber5

is my overclock ok

hi im using the Gigabyte EP45-UD3R and so far i have a q9450@3.2ghz but i really wanted to know what a safe temp is for the cpu and the northbrige
I have a thermalright ifx sli cooler for the northbrige and southbrige no fan and it hits about 55c-58c my cpu cooler is the thermalright xtreme 120mm with silenx 120mm 90cfm one is seems to cool the cpu on on low setting (fan controller)
when primeing my cpu gets to about 58c small ffts (at a max)but is that ok
05-12-2009, 02:58 AM
rubber5

i get sqweeling from my cpu

i get sqweeling from my cpu when prime gets to 14kb testing but it dont change even when i up core voltage does enyone know why
thanks
05-12-2009, 04:03 AM
Hoss331

its normal dont worry about it :up:

Show 100 post(s) from this thread on one page

** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P