Printable View
Well done, took me about 5 hours and it was hard work!Quote:
Originally Posted by WildstarOCT
Managed to extract most of the info I needed, think the template is a good idea and not seen that before in a thread.
The P5Q-Deluxe is a damn fine board, lots of little improvements I notice over previous chipsets I've used, now all I need is one of them new E0 stepping chips and I'm in business!
Enjoy :)
Speaking of the new E0 chips, I notice that the Q9650 has it. Will the Q9450/Q9550 have E0 stepping as well, and about how long tell it hits the shelves? I really want a 45nm chip to go with this board but would rather wait for the Q9650 to drop down to about $300:)Quote:
Originally Posted by Big.Wayne
Can someone give me a walk through to setting up RAID on this board?
I went into the RAID BIOS, set up the slices. Rebooted, went into regular BIOS and set the SATA mode to RAID. Rebooted and inserted the floppy containing the RAID drivers. Went to install Windows XP, pressed F6, and all I see there for ICH10R is "ICH10R SATA AHCI" or something like that... nothing else is there for ICH10R. I choose that one and setup loads it. I continue with the Windows setup and when it asks me if I want to install Windows/repair, I press enter to install Windows. I then get a message saying there are no harddrives connected. Both of my RAID drives are recognized by BIOS/RAID BIOS, so I'm at a loss here. I've got the 1201 BIOS (up from stock 0605) and that didn't help.
Anyone got any pointers?
When flashing between 1103 and 1201, has anyone experienced the settings you left set in the previous version still being there after the flash and reboot?
Before I flash, I set default cpu speed, set ram to DDR800, set vcore to 1.3625, PLL 1.52v, vFSB 1.12v, vNB 1.20v, vdimm 1.98v, set stock multiplier and ram timings, and set PL = 10, then flash to the new bios. I believe it is more guaranteed to be stable than leaving everything on auto. Before today upon entering into the bios after a flash for the first time, everything has been back to 'AUTO' as you would expect. However when going from 1201 to 1103, then from 1103 back to 1201 again, all those settings remained set in the bios. Nothing was changed from the way I had left it set manually prior to the flash.
Has anyone experienced this?
I don't think you need a MM, because I'm just not stable at same NB and DRAM voltages as with 1103. Will try 1.30V NB and 1.98V DRAM instead of 1.26/1.90V.Quote:
Originally Posted by CERO
Before I flash anything I just set all to default and just leave the ram voltage at it's required level... then I flash, and once bios pops up again I reset all again to default but the ram voltage...Quote:
Originally Posted by CryptiK
chispy has done some voltage readings too... NB value is a tad lower and his rams undervolt big time...I'm getting lost in the dark now lol... on my board nothing has changed (since 0901), on yours it's different and on chispy's it's again different :shrug:
Asus P5Q-Deluxe / Voltage Readings / Bios 1201
V.Dim - Bios 2.02 , idle 1.96 = v.Dif 0.06 / Load 1.93
V.Dim - Bios 2.10 , idle 2.03 = v.Dif 0.07 / Load 2.01
V.North - Bios Auto 1.12 ,
V.North - Bios 1.10 , 1.08v. dmm = V.Dif 0.02
V.North - Bios 1.20 , 1.17v. dmm = V.Dif 0.03
Link to his test : http://i4memory.com/94959-post85.html
The discrepancies between our voltage measurements certainly are remarkably large. It is strange that the same boards have such large differences between them.
I have a question - can someone please verify what vNB it takes to be orthos Large FFT stable using 445 FSB (I'm at 445 x 9), DDR 1112 MHz 5-5-5-15, 266 strap, PL 8? I'd really appreciate it.
I'm quite sure it takes 0.06v more vNB to be stable at that setting with the 1201 bios than with the 0803 bios.
I always flash with afudos and extra switches to make sure everything is updated...Quote:
Originally Posted by CryptiK
afuXXX /i<ROM filename> [/o<save ROM filename>] [/n] [/p[b][n][c]]
/n - don't check ROM ID
/pbnc -
b - Program Boot Block
n - Program NVRAM
c - Destroy System CMOS
I usually use full /pbnc but just /pc should do the trick clearing cmos
using "b" is bit risky. If update fails your boot block may get messed.
"They" just want you to feel safe :DQuote:
Originally Posted by WildstarOCT
However, good thread it is.
Just flashed to bios 1201 last night and as far it works great.
Just trying to find my sweetspot for my new bad clocking e8600.
:up:
can you help me out? just flash it to 1201 and everything seems fine in windows. This afternoon, I just tried running OCCT and just after 1 minute and 8 secs, occt will crash with error code 01 :( ... tried just the mix, cpu and ram and they are all crashing. I am just using stock setting and everythins is in auto...windows XP sp2
Spec :
Q9450
P5Q Deluxe - bios 1201
2 x 2g g-skill ddr2 800 5-5-5-15 timing
700W delta PSU
8800 gtx VC
WD raptor 74g hdd as OS
Is there a point where we can measure Vcore on the top of the mobo? The guys at awardfabrik did measure just vdimm,vfsb,vnb and vpll.
Also i read the whole 100+ pages but most people are on Wolfdales. Which is the best bios for 45nm Quads? I'm on the 0803(the one that came with the board).
This is why i wanted to find out where to read VCORE with a multimeter. I'm not sure i can trust the readings.Quote:
Originally Posted by Leeghoofd
It's not a bios problem, you only must set RAID in BIOS.Quote:
Originally Posted by Polizei
It's logic that XP doesn't see your raid if you don't load the RAID driver...:rolleyes:
Scroll through the drivers that you see (move down and up in the windows with the drivers list).
Load also the ICH10R RAID driver, if you have download the Intel driver it MUST be in the list...
@ NaMcO: Well BenchZowner sent me this:
http://i38.tinypic.com/zv7ll0.jpg
http://img329.imageshack.us/img329/9550/zv7ll0ec1.jpg
http://img329.imageshack.us/img329/9...426168b85c.jpg
But i tryed measuring vcore on the capacitor near the EPU chip and it looks like its ground.The other terminal has 5.13V.
If you want to measure the vcore on the backside:
http://www.xtremesystems.org/forums/...&postcount=251
But these are from the P5Q3 model.
how do you flash you bios from 1201 to 803 please
this is the way i have done it ( probably a lazy way :) )
- put a bios 803 in the thumb drive formatted as fat32
- boot the system and enter BIOS, restore to default settings
- power down
- Put the thumbdrive with the bios and power up again
- press alt f2 during power up
- EZ flash 2 will see your bios in your thumb drive
- just update your BIOS and the system will do the trick :)
Why did I re-flashed it to 803?
1. System stability test using everest ultimate will fail after 1 minute.
2. OCCT RAM test or CPU or Mix test will fail just after a minute and 8 secs or so
3. Prime95 will fail fail at thred number 4 after merely 15 secs and thread 3 will fail by almost a minute after excuting it
My conclusion :
BIOS 1201 is not stable with my system. BIOS 803 is the way to go for me.
Quote:
Originally Posted by Leeghoofd
Lee my friend, all the tests were run at 333fsb in a E8400.
I can see all the boards fluctuate on the voltage department after my findings
:shrug:
Just finished some DMM RAM readings, it seems that boards are acting different :shrug:
Asus P5Q-Deluxe / Bios 1201
400 fsb
V.Dim - Bios 2.02 , idle 2.12 / Load 2.13
V.Dim - Bios 2.10 , idle 2.20 / Load 2.21
450 fsb
V.Dim - Bios 2.02 , idle 2.12 / Load 2.13
500 fsb
V.Dim - Bios 2.02 , idle 2.12 / Load 2.13
Same thing here, upgrading 1103 to 1201 kept all settings.Quote:
Originally Posted by CryptiK
ROFLMAOQuote:
Originally Posted by WildstarOCT
nice one! :rofl:
Quick voltage testing with my board reveals:
With a DMM, bios 1201.
vDimm: Bios 2.20, actual idle 2.21, actual load 2.22
vNB: Bios 1.30, actual idle 1.32, actual load 1.33
Mumid, how much vdimm you need to put ya tracers to use stable at the frequencies of your assinature?
i'm puting 2.08 on the bios @ 900mhz 4-4-4-12...my bios is 0803
thanks
There not tracers just standard ballistix but nevertheless 2.20 is required mate. Bios 1201 i set 2.20 in bios giving me 2.21-22. Previous bios' i was setting 2.16 not sure what actual it was giving me. Got a fan on them though because they do get hot, ive got a thermometer inside the heat spreader on them going to an lcd readout and they idle around 34c and fully load upto around 45c.Quote:
Originally Posted by R@ptor =]]
Running them at the setup in my sig gives real good performance though, check out the everest benchmark i posted earlier in this thread :up:
The situation is almost worse than it was... The system now freezes while POSTing or when I'm trying to change settings or voltages in BIOS... It does the same thing when I put my Ballistix D9's in this system and it also does the same thing when I use only 1 stick, in the yellow or black slots...Quote:
Originally Posted by S1mon-
I'm getting really pissed, in the last hour, I have been able to reach Windows once, but it frozen a few second..
I have tried everything, raising the vNB to 1,46V, the memory to 2,1V, selecting every straps, clearing CMOS, etc etc... I have replaced the CPU, rechecked every connectors etc etc
It's the first time in 3 years that I get so many problems with a machine.
I'm about to RMA the board, the CPU and maybe the Power Supply (Can it be it?)
I doubt the memory is the problem since I tried with other sticks...
haev you got an older vidcard laying aorund, did you try unhooking unnecessary devices like floppy drives, DVD writers and co, so just vidcard and HD connected to the PSU ? either the PSU might be it or you got a dud mobo mate...
I tried with my 8800GT, same thing, the PC froze while POSTing... Not a big deal, time to RMA the board and maybe the CPU and Power Supply...