:D How about this one:Quote:
Originally Posted by ToyTen
http://www.xtremesystems.org/forums/...d.php?t=191447
;)
:D How about this one:Quote:
Originally Posted by ToyTen
http://www.xtremesystems.org/forums/...d.php?t=191447
;)
wow, that seems to be a very very good choice. I wait for thoses two kits already: http://www.mediafrost.de/produkte_von_CellShock.html for sure & http://www.memoryc.com/computermemor...inumebkit.html or maybe those(in RMA actually) will be replaced by: http://www.memoryc.com/computermemor...iesrammod.htmlQuote:
Originally Posted by camouflage
Damn Evo!! on my Gigabyte X38T-DQ6 I got thid with the actual ram's ... http://pix.nofrag.com/0/d/f/85f62179...12923f46dt.jpg
Sick of it :p:
:D Evo loves 3:5 divider & hates 1:2 (BIOS 0115) - but You win more of a hi FSB ~580 with 3:5 divider & RAM @ CL7 PL8 as if You go for 1:2 divider @ >1000MHz RAM speed @ slow timings.Quote:
Originally Posted by ToyTen
;)
:) thx Camouflage, i'll do remenber this info . goodnite fella
:D Here we go - now 8.5 x 570:
http://img520.imageshack.us/img520/4...x570cf5.th.jpg
:up::up::up:
great work. I have been away form the board the last few days but will have another go with it over the weekend :)Quote:
Originally Posted by camouflage
:D It's really worth to spend some time on it................;)Quote:
Originally Posted by jabski
well for me it will be very dificulty to do that, my PC just died yesterday after a reboot :shrug: :(Quote:
Originally Posted by camouflage
dont know if there was a cpu or board problem, tested the cpu in a P5K-E and also didenīt work so lest hope that the mobo is ok, rma on the way!
regards
:( I feel sad to hear this mate - but I guess it's the chip. If You didn't push more than 1.7 Vnb on air the chances are hi that the board is still alive...:rolleyes:Quote:
Originally Posted by jpcastro
Did You try different RAMs on the other board, too?
I'd be a bad suprise if Your RMA'd chip arrives and refuses to work caused by a bad RAM stick..........;)
hiQuote:
Originally Posted by camouflage
tried with other memories the ocz gold that i used before buying the gskill hz and no go, the cpu blue led starts blinking and simply dont boot.
confirmation from the store has arrive, cpu is ok so the problem is the board has died with less then a month of use :shakes:
they will try a hotflash but the best chance is to have a new one, only problem is the waiting time now at least one week and depends if they have in stock :(
lets wait and see....
;):rolleyes: Hm, now You're one step further - You know where the problem is located.....Quote:
Originally Posted by jpcastro
What was max. voltage You gave to the board? Maybe it's a BIOS recover error - sometimes it happens after a failed OC try that the recover function refuses to work and the BIOS hangs. Had the same problem with a different ASUS board - I can't remember, but I think it was a 975 chipset.
Go for RMA & You'll get a new one........................
hy
the more strange is that i was not making tests, it simply died after a normal reboot daily use.
already send to the store and if they have it in stock i´ll get a new one next week, just in time for the new cards arrive @ 2x4870 :)
new tests will start after that and lets see if with a new board the HZ finally gets stable at 1T like yours.
thanks :up:
edit: btw ppl with the board start checking this thread using a evo "HD4850 3x CrossfireX First tried" - http://www.xtremesystems.org/forums/...d.php?t=191870
:D Good luck to You mate - hope You come back soon with new board & new results...........;)Quote:
Originally Posted by jpcastro
DANG! My OCZ sticks turned out not being willing to run in dual channel after replacing first QX9770 with a better one, so I have switched to some Corsair Dominator XMS3-1800 sticks refered to as CM3X2G1800C8D (2*2048). Was no way the board would fire up after new CPU was in place??? Anyone else experienced this on the P5E64 WS board?
Change turned out nice as I am now running (24/7) 4.620 MHz with 440 FSB (10.5 multi) and sticks at 880 MHz at 8-7-7-24 @ 1.96V. Will start to look for higher and tighter now...
- Rob
Hi Rob, I suppose those sticks are the same as mine. Please share settings.Quote:
Originally Posted by Rob Halford
I had to back down to 9x445 to be Prime95 Blend stable (at least 18 h) with the following settings:
CPU Features
Ai Overclock Tuner Manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: 333
FSB Frequency: 445
PCIE Frequency: 100
DRAM Frequency DDR:1800MHz
DRAM Command Rate: 1N
DRAM CMD Skew on Channel A: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on Channel A: Auto
DRAM CLK Skew on Channel B: Auto
DRAM Timings
DRAM Timing Control: Manual
CAS# Latency: 8 DRAM Clocks
RAS# to CAS# Delay: 8 DRAM Clocks
RAS# PRE Time: 8 DRAM Clocks
RAS# ACT Time: 24 DRAM Clocks
RAS# to RAS# Delay: Auto
REF Cycle Time: Auto
WRITE Recovery Time: Auto
READ to PRE Time: Auto
READ to WRITE Delay(S/D): Auto
WRITE to READ Delay(S): Auto
WRITE to READ Delay(D): Auto
READ to READ Delay(S): Auto
READ to READ Delay(D): Auto
WRITE to WRITE Delay(S): Auto
WRITE to WRITE Delay(D): Auto
Write to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled
Ai Clock Twister: Auto
Ai Transaction Booster: Auto
Voltage Settings
CPU Voltage: 1.48125
CPU GTL Voltage Reference: 0.67x
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.36
DRAM Voltage: 1.82
NB Voltage: 1.53
NB GTL Voltage Reference: 0.67
SB Voltage: 1.2
Clock Over-Charging Voltage: Auto
Load-Line Calibration: Performance
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
Configure Advanced CPU Settings
CPU Ratio Setting: 9
C1E Support: Disabled
CPU TM Function: Disabled
Vanderpool Technology: Disabled
Max CPUID Value Limit: Disabled
The performance level (tRD) is 7 and it is a no go to lower to 6. I have a hard time getting CPU/RAM higher with stability. I have tried 9x456, 2N, vcore 1.5 (LLC Performance), NB 1.55 but it's not stable and often my Intel Matrix RAID 1 will turn into "verify" mode which results in extreme instability. I have my 2 Samsung 1TB in a RAID 0+1 setup. I suppose I may OC more without using software RAID. A strange thing is I have used CPU GTL og 0,63 for a long time (based on systematic tweaking) but suddenly 0,67 turns out to be more stable (maybe because when OC too aggressive I "loose" my RAID 1 partition ("verify") which mess up tests untill the RAID array is "normal" again.
Does anybody have suggestions how to push it further and/or tighten timings? I have not yet reached to the point of systematically tighten timings since I had so much trouble getting a stable "base" OC. My max temps have not yet exceeded 60 full load (RealTemp 2.6).
I will try to up the memory voltage and tighten the REF Cycle time as a start.
I'm about to get a headache here in the Banana Republic... After 24 hours of testing and system found stabile, I am suddenly getting BSOD's all over the place. I even managed to play BF2 for 6 hours with new RAM at 1760 (8-7-7-20) and with CLK Skew set to 50 Advanced settings and today it is a no go... Board won’t even boot at 8-8-7-24 so I have had to back down to 8-8-8-24 (which is standard for this RAM at 1.8V).
CLK Skew that was set to 50 advanced is again set to AUTO
CPU PLL Voltage is set to 1.66
FSB Termination Voltage set to 1.34
DRAM Voltage set to 1.9
The rest of the voltage settings are now set to AUTO.
Load-Line Calibration is still giving me BSOD’s no matter what when set to Performance, so set to Normal...
@Holmer, you can probably raise the CPU PLL Voltage to 1.7 for higher stability. RAM is based on Samsung (http://www.samsung.com/global/busine...m=M391B5673DZ1). This link for our RAM will probably help you out a little bit although I am not even close to achieve their results... (http://www.xtremesystems.org/forums/...d.php?t=187853).
Here is what i manage to do with mine. I think cpu prevents me to bench higher
Bios 0115
http://img58.imageshack.us/img58/7972/spiwsevovz1.jpg
CPUz at 600 FSB / 9.5 multi :
http://valid.x86-secret.com/show_oc.php?id=378757
I got BSOD at 605 fsb :(
1:1 memory is the best - if u seeking for max fsb.
Thanks a lot, I will work in that direction. That thread you link to looks like one worth a subscribtion.Quote:
Originally Posted by Rob Halford
thanks camou :up:
so like it was said before it seems and confirms that 0115 is the best bios for max FSB, as for ram OC still donīt know after seeing all results in the thread wich one is better specially to get 1T stability.
btw one thing i didenīt tell before but maybe is just a coincidence, the mobo died less then one day after flashing to the non-oficial 0501 :cool: most certain a coincidence.
lets hope that the new one arriveīs next week, already tired of being on a laptop :shakes:
A bit OT, but.. is there any real-world benefit to 1T? I've not tested everything, but did try WinRAR and compiling code (which is as much as I can time), and saw absolutely no difference.Quote:
Originally Posted by jpcastro
Not to mention I can't get 1T to work even with 1.95vDIMM :( (2T works @ 1.8vDIMM)
hyQuote:
Originally Posted by alfaunits
1T is great for ram bandwitch and lantency, check and compare results with everest using 1T and 2T you will notice quiet a difference.
for games is also good because with more bandwitch the overall performence will be more "fluied" specialy with high-end cards or multi-gpu.
of course that 2T is more common and delivers a good performence to but if you can get 1T dont think twice!
:up:
So, I'm contemplating upgrading my Maximus Extreme to either this board or the P5E3 PREMIUM/WIFI-AP @n. Just looking for the best stability and non-pita board. Any thoughts/comments/suggestions?
this board still has problems. Maybe P5E3 for a easy life or take a look at the P5q3 ;)Quote:
Originally Posted by gs274
:D The board has no problem - but the ASUS guys. New BIOS is required for better work - only 0115 works with all dividers.Quote:
Originally Posted by jabski
;)
NB on air cooling, Only cpu under D-Tek fusion with noozle kit: 3DM03 105902 marks http://pix.nofrag.com/6/3/3/25d05e65...9504694ftt.jpg
-Ai Clock Twister auto
-Ai Transaction Booster auto(PL 11)
-vcore bios 1.41v
-CPUGTLRef 0.67
-vpll 1.52
-vfsb 1.36
-vddr 1.90
-vnb 1.53
-NBGTLRef 0.61
-vsb 1.05
-COC 0.80
-LLC performance
And a Prime95 small fft testing: http://pix.nofrag.com/8/b/8/9216af13...d8300ea1tt.jpg
Here I had to push more vcore: 1.43 in the bios :( but I 'm not pissed off :p: )
With 543 fsb, I can't get a good clock2clock performing setup. My very best at this day would be 531x8 ram:@
I have it hard without good memory sticks, plus me isn't too skilled with ratio's and timings, so here I'm stuck atm...