DD Double Wide Tower - 21 White Series Edition[Custom]

DANGER DEN DOUBLE WIDE TOWER 21
WHITE SERIES EDITION
VER. MORA3 9x120


Haven't touch water-cooling for years since the acrylic top disaster destroyed my whole system included 2x 9800GX2.
Now i feel like to start a whole new silent system and being more carefully on blocks ...avoid acrylic tops especially!!
The whole system will be building around DangerDen Double Wide 21 SR Case. But in Custom Opal White acrylic instead of black[/FONT]

Hardware
CASE: DangerDen Double Wide 21 SR - White Series Edition [DD Custom]
MB: EVGA X58 Classified3
CPU: X5675
RAM: Corsair Dominator GT 6Gb DR3 2000
GPU: Inno3D GTX580 3Gb SLI
Audio: TBA
PSU: Corsair AX1200
ODD: BlueRay
Storage: Intel SSD 510
Sleeving: MDPC-X White
Display: APPLE 30' Cinema Display

Cooling
CPU Block: EK HF
GPU Block: EK-FC + Nickel Blackplate
MB Block: EK EVGA EK-FB Classified
RAM Block: EK-RAM
Pump: DDC 18W x 2
Top: EK DDC x 2
RAD: SINGLE LOOP ->Watercool MORA3 9x120 + TFC XCHANGER 360 White Edition
RES: Aquatube or DD-RAD-RES
Fan Controller: Aquacomputer Aquaero 5 + Aquaero LT Water-cooled
Flow Meter: Aquacomputer High Flow Sensor
Temp Sensor: Aquacomputer Inline
Fluid: FLUID XP+ Ghost
Case Fans: ENERMAX CLUSTER 120mm(10) 80mm(3)
RAD Fans: ENERMAX CLUSTER 120mm(18)
Fitting: 3/8" Comp Fitting + QR

DangerDen Case
May 24, 11
The case was installed in less than 30mins, i must say the quality and fitting was very good.
Since theres still some white acrylic leftover, i ordered an extra white front panel in case i want white after.
http://img709.imageshack.us/img709/263/dsc00004ci.jpghttp://img194.imageshack.us/img194/855/img1231ep.jpg

http://img405.imageshack.us/img405/4421/40072687.jpg

http://img151.imageshack.us/img151/9643/47940106.jpg

http://img196.imageshack.us/img196/7955/92549434.jpg

RADIATOR MORA3 9x120mm
May 25,11
Just test fitted the MORA3, the rad came with 4 standoff, i assume its for the case when you put fan between rad and panel, but the standoff was too short for that, now i must try to find a longer standoff or longer screws+adapter.
WHat! There's white version Mora.. Dammit..
http://img5.imageshack.us/img5/212/img1234q.jpg

HARDWARES
May 26,11
90% arrived !! Now have to decide on the Liquid, Fitting.
http://imageshack.us/m/217/1354/harda.jpg

Subbed because I like white cases :-)
Good Luck !

costume white DD case :shocked:
can't wait to see it .

White DD :0 I WANT ONE NOW HAHAHA

Pictures...:D

Quote:

---

Originally Posted by quattro_

costume white DD case :shocked:
can't wait to see it .

---

Feel free to contact Debbie to cancel their holidays :welcome:

Quote:

---

Originally Posted by Raiden

White DD :0 I WANT ONE NOW HAHAHA
Pictures...:D

---

She promised me only one will be produce, you can beg for my approvel. :D

Here's some of the hardware currently parked in my old MM case. Nice case but heavy, scew holes not line up very well, the backplate as well, need force to install MB with few screw left out, video card pain to install as well....not line up with MB..etc. Hope the newer production quality been fix on these issues.

Thats my re-entry Corsair H70 cooling kit. Yes, very safe but noisy as hell.

http://www.xtremesystems.org/forums/...1&d=1304228580

man, i cant wait to see what this l00ks like...

any eta from debbie? she's a sweetheart, isnt she...

subbed - this sounds nice

Quote:

---

Originally Posted by ballzD33P

man, i cant wait to see what this l00ks like...

any eta from debbie? she's a sweetheart, isnt she...

---

No idea on ETA, she saids the white acrylic in transit 3 days ago.. i guess production + shipping, roughly 2 weeks at least..

Yes, debbie was helpful thru the whole process with many of my custom requests..

I freaking love that case.

subbed

The white acrylic sounds like it will look sweet. Quad, have you thought about what the color theme will be for the build, such as accent colors to the white or what type of sleeving/wire colors you will use? Project Saifu and Raiden's project pretty much showed me how beautiful these DD cases can turn out, so I'm looking forward to following this build!

That's one fantastic looking case! Looking forward to the completed build! :up:

Quote:

---

Originally Posted by Beriphent

The white acrylic sounds like it will look sweet. Quad, have you thought about what the color theme will be for the build, such as accent colors to the white or what type of sleeving/wire colors you will use? Project Saifu and Raiden's project pretty much showed me how beautiful these DD cases can turn out, so I'm looking forward to following this build!

---

I am not sure at this moment, but all white sleeve ordered from MDPC-X.

Many white delrin/acetal !!!

Lots of white Leds !!!

Lots of Fans like 30 of them..

A white Double Wide? That will look awesome :D! Will you be using red as the secondary color theme?

Quote:

---

Originally Posted by Alexandr0s

A white Double Wide? That will look awesome :D! Will you be using red as the secondary color theme?

---

Red with White should be interesting, but i have no red MB, just a FTW3, i will definitely try that when the X79 red EVGA came out..:eek:

Subd! just because i like white cases :D

MDPC-X SLEEVING

Parts are flying in from everywhere around the world...

MDCP-X

40m White 1/8
10m SATA

Free color sample...Nice
Funny Sketch....But seen this exact drawing many times.. i guess he ran out of idea from tons of orders..

Enermax Cluster White Led PWM Fans

120mm x 28
80mm x 3

got the fan for approx. $14 each.. These fans were the best looking fan i ever seen; performance wise, i don't think they are idea for Rads.. i presume the pressure will be leaking from the side vent.

Since i am doing low rpm Push Pull, i don't really care..agree?

Quote:

---

Originally Posted by QuadSLI

Enermax Cluster White Led PWM Fans

120mm x 28
80mm x 3

got the fan for approx. $14 each.. These fans were the best looking fan i ever seen; performance wise, i don't think they are idea for Rads.. i presume the pressure will be leaking from the side vent.

Since i am doing low rpm Push Pull, i don't really care..agree?

---

I have them in Holocon . . .
http://www.xtremesystems.org/forums/...d.php?t=269649

Wish I had thought of white acrylic. Can't wait to see your build!

I have enermax clusters on a 360 swiftech quiet power rad cooling a 980x(4.2ghz) and they work pretty well, temps between 45-50C loaded.

Quote:

---

Originally Posted by DarthBeavis

I have them in Holocon . . .
http://www.xtremesystems.org/forums/...d.php?t=269649

Wish I had thought of white acrylic. Can't wait to see your build!

---

OF course i had studied yours, thats one hardcore build :clap:, im nowhere near that...

Comon, its time for some refresh in new black.. get some from Debbie...

BTW, please give comments/advice along the build...

Quote:

---

Originally Posted by =[PULSAR]=

I have enermax clusters on a 360 swiftech quiet power rad cooling a 980x(4.2ghz) and they work pretty well, temps between 45-50C loaded.

---

I feel better now:toast:

Is that in Push/Pull? Pos+/ Neg- fan pressure ?

Quote:

---

Originally Posted by QuadSLI

OF course i had studied yours, thats one hardcore build :clap:, im nowhere near that...

Comon, its time for some refresh in new black.. get some from Debbie...

---

You will surpass it bud. Just keep up a nice worklog for us please.

Quote:

---

Originally Posted by DarthBeavis

You will surpass it bud. Just keep up a nice worklog for us please.

---

Hey DarthBeavis,

May i ask what liquid you were using in ur build? Fluid xp Ghost white or Ice Dragon Nano??

AQUAERO 5 Controller

Another box arrived..

Aquaero 5 w/ Heatsink
Temp sensor
Flow meter

Now i have to figure out how to connect all these fans to the aquaero... 1 pwm already reserved for pump pwm signal.. 3 port left.. enough power..??

I am planning on getting another Board and Graphic card, so i can build them without downtime..

Any suggestion, i limited to these choice..

MB
1) EVGA X58 Classified 3
2) RE3 Black Edition
3) RE3
I place EVGA on top since it gave me trouble free on bios..etc, compatibility.. ease of use. Asus always need fine tune and bios update..etc..
Evga Class 3 price seems great now.

VGA
1) Zotac GTX580 3GB
2) Zotac GTX580 3GB AMP2
3) EVGA GTX580 3GB
Purely on price on the placment, plus they're reference card for the EK-FC580 block i already ordered.

I will go ahead unless someone have some bad to say about them..

MMmmm DD Double Wide 21 is very popular now.. I just received mine a couple of weeks ago, and waiting for parts like you and plan on starting a build log this week. I did not know they had white? I decided with SMOKED version.. Looking forward towards your build.. :up:

Quote:

---

Originally Posted by Lu(ky

MMmmm DD Double Wide 21 is very popular now.. I just received mine a couple of weeks ago, and waiting for parts like you and plan on starting a build log this week. I did not know they had white? I decided with SMOKED version.. Looking forward towards your build.. :up:

---

Terrific, im not alone:alien:

They don't have white acrylic at all, its just my special request, of course with Debbie's great help.

GTX 580 3Gb

Ok,

I end up getting a Inno3D GTX580 3Gb reference.

I heard few cases even tho it saids reference, the waterblock don't fit perfectly.

So i just grab 1 card to test fit, and this was the only 3GB available on the shelf.

Ok, now do they look that reference??

God, i luv these fans..

Quote:

---

Originally Posted by QuadSLI

Hey DarthBeavis,

May i ask what liquid you were using in ur build? Fluid xp Ghost white or Ice Dragon Nano??

---

Fluid XP (Arron sent me a couple bottles of it).

Quote:

---

Originally Posted by DarthBeavis

Fluid XP (Arron sent me a couple bottles of it).

---

Humm.. Arron:confused:

So, do you recommend this liquid? Will they went clear over time..etc? residue??

I dont visit the forum that much.. may be you can point me to him, he's selling it???

I am sorry that it has been a long wait since thread started..

Finally the package arrived, stay tune for tomorrow for the case

Arron runs Fluid XP. I have not run it that long so I cannot say how the coolant will hold up. Anytime you use a colored coolant you are taking your chances and there are trade offs.

Quote:

---

Originally Posted by QuadSLI

I am sorry that it has been a long wait since thread started..

Finally the package arrived, stay tune for tomorrow for the case

---

Looking forward to it! :up:

I absolutely cannot wait to see more pictures of this build.

Quote:

---

Originally Posted by DarthBeavis

Arron runs Fluid XP. I have not run it that long so I cannot say how the coolant will hold up. Anytime you use a colored coolant you are taking your chances and there are trade offs.

---

Thanks Darthbeavis..

Anyone had experiences with Dragon Ice nano ??

when will you get the case? I so want pix

Quote:

---

Originally Posted by DarthBeavis

when will you get the case? I so want pix

---

Sorry, too much alcohol last nite, just half finish..... But all i can say is i loving it already..

That milky white acrylic is amazing looking. :up:

:up:;):cool::clap:

you NEED to buy MNPCTEch feet and paint them white for that baby!!!

Quote:

---

Originally Posted by DarthBeavis

you NEED to buy MNPCTEch feet and paint them white for that baby!!!

---

Any idea welcome!!

Actually i am wondering if i can find some nice roller feets..

NO! no roller feet.... dont make it a MM!

http://www.snotr.com/video/1307/When...ters_get_bored

You are liquidcooling it... you might as well do what thsoe guys did!

on a more serious note.... unless you can find the most AWESOME white, ROLLER feet, i would suggest against it...

Love that white inside and front. I think inside white front,top, and rear should be smoked with sides clear with black case feet or white... I agree 1+ on no rollers..

Photo Uploaded on Post#1 !

The installation was piece of cake. Great quality and everything line-up perfectly.

Quote:

---

Originally Posted by QuadSLI

Humm.. Arron:confused:

So, do you recommend this liquid? Will they went clear over time..etc? residue??

I dont visit the forum that much.. may be you can point me to him, he's selling it???

---

I used Fluid XP for a year and a half (blood red). Never faded and seems to work really nicely. Expensive, but I really liked the colour so was worth it. Defenite temperature improvement over Feser 1 I used before *cough*.

HARDWARES
May 26,11
90% arrived !! Now have to decide on the Liquid, Fitting.
http://imageshack.us/m/217/1354/harda.jpg

QuadSLI not sure if you have a dust issue where you keep your computer stuff. I recently purchased for my system 2 x Custom DEMCiflex Magnetic Triple 120mm Radiators Dust Filter Fans for the intake area and 1 x DEMCiflex 140 Magnetic Fan Dust Filter Round for the bottom intake area for the Power Supply I here they work great on keeping the dust out. The dust filer comes with its own sticky side to attach to the case and the other side comes apart via magnet to clean the screen easier.

http://www.performance-pcs.com/catal...ple-Rad_01.JPG
http://www.performance-pcs.com/catal...-140-BK_01.jpg

Quote:

---

Originally Posted by Lu(ky

QuadSLI not sure if you have a dust issue where you keep your computer stuff. I recently purchased for my system 2 x Custom DEMCiflex Magnetic Triple 120mm Radiators Dust Filter Fans for the intake area and 1 x DEMCiflex 140 Magnetic Fan Dust Filter Round for the bottom intake area for the Power Supply I here they work great on keeping the dust out. The dust filer comes with its own sticky side to attach to the case and the other side comes apart via magnet to clean the screen easier.

http://www.performance-pcs.com/catal...ple-Rad_01.JPG
http://www.performance-pcs.com/catal...-140-BK_01.jpg

---

They are useful but the worst in the look department tho, i cant imagine when they were sticking in the front of my case:eek:

Im looking into the filterRight, but they are too dense...

did you find out whether waterblocks fit that inno3d gtx 580?


i was wondering the same

Quote:

---

Originally Posted by F3L1X

did you find out whether waterblocks fit that inno3d gtx 580?


i was wondering the same

---

Yes, it does fit the Inno3D GTX580 3Gb, so as for the EVGA GTX580 3Gb as well i assume..

Will these look geat on the front panel...:rolleyes:

http://www.mnpctech.com/120mm_custom...h.com_site.jpg

IN hand Modular Enermax Maxrevo 1350W
http://img197.imageshack.us/img197/9662/img1242w.jpg
http://img641.imageshack.us/img641/4210/img1243dg.jpg
http://img204.imageshack.us/img204/2268/img1244e.jpg

nice psu! Quick question, are the ATX 24pin 1 to 1? what i mean is, does the 1st pin that plugs into the psu, go into the 1st pin on the atx24 mobo connector? 2nd pin to 2nd pin, so on and so on?

Quote:

---

Originally Posted by barfastic

nice psu! Quick question, are the ATX 24pin 1 to 1? what i mean is, does the 1st pin that plugs into the psu, go into the 1st pin on the atx24 mobo connector? 2nd pin to 2nd pin, so on and so on?

---

Nope !

First of all, the connectors on the PSU were difference design, so aftermarket ready made cable will not work without modding.

ATX+CPU: Only 20pins and share the rest 4pins from another 16pins port into 24pin and 8pins, Most were 1to1 except a 2to3
http://img171.imageshack.us/img171/6510/img1245ia.jpg
http://img695.imageshack.us/img695/8342/img1246mm.jpg

PCI-E: 12pins to 6+2 , 6+2 , contains 2 set of 3to5
http://img821.imageshack.us/img821/7404/img1247mq.jpg
http://img840.imageshack.us/img840/8513/img1248od.jpg

CPU2 : 12 to 8+4 . 1to1
Molex: 5 to 4 , 1to1
Sata: 5 to 5, 1to1

I have ordered bunch of BitFenix cable just to get those solid white connector..
http://cdn2.specialtech.co.uk/spshop...ZUAD_218_1.jpg
http://cdn2.specialtech.co.uk/spshop...ZUAD_281_1.jpg

Headache!! :shakes:
Any member here wanna do some sleeving?

wow.... thats confusing as SHIZNIT!
good luck with that man :D hope everything works out for you!

The bitfenix look nice. There was another build around here that used those extensions instead of modding the PSU.

In my opinion it is better to use the extensions and cable manage it so that you can't see the regular connectors.

Keep up the good work! :up:

Been held back by the EK Nickel thing..

Attachment 116416
Attachment 116417
Attachment 116418
Attachment 116419

I would have front panel recut in white

Quote:

---

Originally Posted by DarthBeavis

I would have front panel recut in white

---

+1

Loving the build so far... I dread to think how much you've spent so far.

Quote:

---

Originally Posted by DarthBeavis

I would have front panel recut in white

---

You referring to my case front panel? It is white but now i look at it kinda of outdated..

This build reminds me of my build (3 x 3 radiator front). My hat's off to you, sir!

Quote:

---

Originally Posted by UrbanSmooth

This build reminds me of my build (3 x 3 radiator front). My hat's off to you, sir!

---

Nice build you got there.. Black/ Blue was my other favourite.

http://img825.imageshack.us/img825/9334/img0338r.jpg

How are those White Twister Clusters compared to the Scythe GTs for radiators?

Quote:

---

Originally Posted by LLiH

How are those White Twister Clusters compared to the Scythe GTs for radiators?

---

The Cluster only offer 1150rpm while the GT offering full range from 800 -2000 something like that.
From what i have read, GT dominated in every category..

I choose Cluster simply because the look and yet quiet low rpm and of course white LED

Aug 6, 11
I am back!

I decided to get another aquaero LT to control all the fans and 2 pump pwm control port now. Just received the long out of stock AQ block.
http://img713.imageshack.us/img713/1665/dsc00030xs.jpg

Cool Mouse !
http://img692.imageshack.us/img692/1956/dsc00032oz.jpg
http://img833.imageshack.us/img833/9256/dsc00034no.jpg
http://img801.imageshack.us/img801/6047/dsc00031ds.jpg

WORK LOG

Aquaero Pro & Billet Switch
http://img834.imageshack.us/img834/9407/dsc00029oh.jpg

Corsair AX1200 White Sleeved
http://img846.imageshack.us/img846/7198/dsc00026qw.jpg

There the MO-RA3 hidden in the other compartment
http://img6.imageshack.us/img6/7163/dsc00027lj.jpg

EK HF CPU block & bracket covered in white carbon + EK MB Block + EK RAM
http://img708.imageshack.us/img708/3375/dsc00028mu.jpg
http://img269.imageshack.us/img269/6946/dsc00023cz.jpg
http://img535.imageshack.us/img535/5610/dsc00024xx.jpg

MCP35X + EK white top + Koolance Heatsink
http://img851.imageshack.us/img851/4209/dsc00025up.jpg

TFC XChanger 360 White edition + DangerDen Res
http://img705.imageshack.us/img705/2271/dsc00021gr.jpg

EK FC580 + Blackplate
http://img26.imageshack.us/img26/7580/dsc00022lw.jpg

Full Shoots!! Ahw.. i suck in photoshooting... that it for now.. still waiting for few stuff to complete..
http://img707.imageshack.us/img707/2397/dsc00020bf.jpg
http://img52.imageshack.us/img52/9001/dsc00019nzo.jpg

Wow very nice, it looks like with the MO-RA3 you are unable to use a front right side radiator there? I wonder if it would fit in the roof of this build?

I have a question for you I keep seeing this mouse pop up on many different builds just wondering where did you buy it and is it used for CAD or something like that? I saw it on this build ----> H E R E

Looking good...
Attachment 118680

Quote:

---

Originally Posted by Lu(ky

Wow very nice, it looks like with the MO-RA3 you are unable to use a front right side radiator there? I wonder if it would fit in the roof of this build?

I have a question for you I keep seeing this mouse pop up on many different builds just wondering where did you buy it and is it used for CAD or something like that? I saw it on this build ----> H E R E

Looking good...
Attachment 118680

---

I can still barely fit a BlackIce Stealth at the right compartment front and back. Yes you can fit any 120.3 , 140.3 or 120.4 if no disc driver at the roof but i didnt ask for mount hole.. tho.

Its just a nice looking adjustable gaming mouse.. but the shape are awful..

looks much better all white. I would paint the PSU as well . . .peel the stickers off the fans perhaps. The front does not look as good with just one set of fans on the rad - push/pull would look way cleaner. Maybe some white fan grills as well. Check out MNPCTech

Ya, exactly.. i didnt mount the front rad yet... i need a new one , that one in picture was totaled since i flushed it with vinegar and failed...

looks like you might not have room with two pumps on the bottom. I love it all so far though. Danger Den has a white case at the last PDXLAN.

Time to plump!

Quote:

---

Originally Posted by DarthBeavis

looks like you might not have room with two pumps on the bottom. I love it all so far though. Danger Den has a white case at the last PDXLAN.

---

You are correct..haha..
I was thinking mounting them to the rad fans but couldnt find a bracket for DDC .... the UN bracket might work but i dont like it.
Also may be the HD cage below PSU..

The replacement 360 Rad came in today... cant wait to power it on..

http://img15.imageshack.us/img15/8624/img1289dd.jpg
http://img838.imageshack.us/img838/4986/img1290i.jpg
http://img263.imageshack.us/img263/1411/img1291bb.jpg
http://img94.imageshack.us/img94/1577/img1292r.jpg
http://img268.imageshack.us/img268/4389/img1293hv.jpg

Just want to say loving everything about your build!
Looks awesome mate!

How do you like the mouse? You said it didn't fit right, or was that about something else?

Its very flat vs the other mouse round top. With the round top it more of a relax position.

Quote:

---

Originally Posted by Phatboy69

Just want to say loving everything about your build!
Looks awesome mate!

---

Thank you, glad you like it... look forward to your new build..

Today mounted shroud and fans.. huge case seems out of space all da sudden...

Now i need to find some space for the 2 pumps... as the DD res mount to the center of rad and no room for the pump to be side by side.. i am thinking mounting a EK Res to the back panel to solve the space problem.. Any suggestion....:D

http://img855.imageshack.us/img855/2157/dsc00037pa.jpg
http://img844.imageshack.us/img844/5181/dsc00036ns.jpg

Is it possible EK so kind to make some white POM Res top/ bottom .. just wondering..

Anyone knows him made be drop him a line...

Swap DD RES to EK RES.. so far so good..

Now, just waiting for some Bitspower stuff and their new item to try out on my build.... i m not sure what it is yet...

http://img143.imageshack.us/img143/3905/dsc00038jt.jpg

Yeah the build came along nicely... As for a suggestion for the pumps, I would get rid of the shrouds on the front rad so it opens that space up better. Plus I doubt there would be any temp difference TBH! But that extra inch of space would really un-cram the pump section of the case!

I was thinking talking those off too if space need.. its just purely cosmetic... just thinking it will be nice when the fan led reflects from the shroud..

The PWM splitter cables ready... all goes in Dual AQ5.. BTW can you mix fans in one splitter cable ?? 80mm and the 120mm....

http://img189.imageshack.us/img189/215/dsc00039hu.jpg

Re-sleeve some of the cable.. the blue/red cable color went thru the white sleeve easily... so i sleeve them with heatshrink then sleeve it, crystal white now...

http://img849.imageshack.us/img849/2575/dsc00040ot.jpg

Nice Build so far. Remember to use this. make it look like milk. )

http://www.heatsinkfactory.com/fluid...ost-white.html

http://www.xtremesystems.org/forums/...y-Tadzik/page3

TKS...

Liquid .. Check :)

http://img847.imageshack.us/img847/2422/dsc00041xq.jpg

Quote:

---

Originally Posted by QuadSLI

Its very flat vs the other mouse round top. With the round top it more of a relax position.

---

Yea, that R.A.T. mouse is a bit odd. I still haven't got used to mine. It's very heavy (even with all the weights removed), rocks if you put the pinky attachment on and is a bit stubborn when it comes to dbl clicking. Did you ever find a use for the thumb scroll wheel?

Love this build by the way... this white on white is just sick. sub'd :up:

Sick.. loving it

Quote:

---

Originally Posted by Raiden

Sick.. loving it

---

DangerDen case Rock.. i wouldn't buy any other case...

I would have brought the 29 if i know they exist..

Hey , I've been checking out this build and I goto say... NICE JOB! Any chance you could post some updated pics of the final thing?

I'm not saying this is what happened... But from my experience I know that a lot of people have an idea about how the build _should_ go. And well, at some point people want to use their equipment and end up making sacrifices in the organization and layout, just so that they can _use_ the equipment. Then the threads don't get updated, because frankly, the OP might not want to post the rig in an incomplete or unfinished state. I don't know if that happened here, just pointing out the possibility. And I'm guilty of building monster rigs and never truly "finishing" them. maybe it's a coping mechanism. :D

Very sorry for the pending project, i went into some dilemma on the fittings / routing .. and just left it there, went to some of my other big toys and work..etc.
When i had the time to go back, i had my eyes on the x79..ivy bridge..hybrid psu

Shame man... I thought the build was looking really good

To be continued?

Quote:

---

Originally Posted by LRV

To be continued?

---

Let's hope so!

never seen a case like that !

im loving the different design of it and the looks for me are awesome.

i have just sold 16 of those enermax cluster fans from my mountain mods case,they are very very nice looking fans are also very quiet.

gone for 16 better fans for 3xrads.

keep up the good work and ill be keeping a eye on this build now.

Edit - Sorry, just read the rules, this was the wrong place to be asking. Post deleted.

Come on, man! Stop playing around and get back to this.

I was thinking of getting a similar white DD 29. How do you like yours? It almost seems like a transparent white ?