Hi i'm searching for a Vcore and Vmem Mod for this card:
If you need any more info, just ask
Hi i'm searching for a Vcore and Vmem Mod for this card:
If you need any more info, just ask
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Measure the voltages on pin8 of the RT9214 ICs. Also, a pic of the front of the card would be useful.
Don't know which one is pin 8 so did this 4
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Don't have a digicam so can't take any pics of my own card but this is a pic from the front from annother one
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Hi,
Is there the same code 'RT9214'-code in both chips ?
I wonder those are regulators by richtek, and 'interesting node' should be #6. (BTW, In RT9214 regulator there should 0.6 V in that node..)
http://www.richtek.com/Product/Docs/DS9214-06.pdf
I marked those pins with yellow in figure below. The output voltages are found most likely in some of the points you marked, I think the nodes marked with purple below are Vmem and Vcore (?).
Modding of RT9214-regulator is quite simple: connect high value e.g. 50 kohms variable resistor between a 'yellow' node (=FB, pin #6 in datasheet) and GND. Lower resistance = higher output voltage. E.g. green nodes are GND, but GND can be found also several other places in card.
Oke thanks man
I will try it asap
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Oke thanks. But does it has to be 50K VR. Atm I only have 10k and 20k pots in stock
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Did the VDDR mod with 20K VR and it works fine
Only the result is less
Without Vmod: 1180
With Vmod: 1220
Maybe some other cooling will work.
Vgpu mod comming up, just as pics
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Here a some pics of Vmod for now. VDDR Measure point did stick very good so isn't on now.
Sorry for bad quality. Is with webcam.
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
Man you got me scared, why are you using wires this thick on that pot???
I understand the mesure pts but dude, be careful!
Suma.
O lol. I did use the hole wire
Only some little lines of the hole wire
And what does it matter how thick the wires are. The thicker, the better i think?
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
For the ones how want to, some pics of the Vcore Mod too:
Sorry for bad quality
Last edited by UTF Nightmare; 02-07-2006 at 12:38 PM.
Epox 9NPA+ Ultra - Opteron 146 0530 APMW
Infineon BH-6 2x256mb - Tagan 480W-U22
Gainward 6600GT Vmodded - Kingston HyperX BH-5 2x256mb
Infineon BH-6 280MHz 2-2-2-5 @ 3,77V - 3602MHz - PhCh mem Project
results?
Venice 3200@2700 1,64v ( 300x9, divisor @166 )
DFI Ultra-D
2x512 bh5 245 1t 2-2-2-5
Powercolor x850xt 560/1260
Bookmarks