The OP is up to date. :D
Good job everyone! :up:
@ kimandsally
Any chance you can crop your posted image with your cute kitty so it's not so wide? :) Stretches the page's width quite some and a bit over the top. ;)
Printable View
The OP is up to date. :D
Good job everyone! :up:
@ kimandsally
Any chance you can crop your posted image with your cute kitty so it's not so wide? :) Stretches the page's width quite some and a bit over the top. ;)
My turn, finished to build & test new christmas rig:
i7 920 D0 at 4.5GHz (HT Off) giving 66 GFlops with 1.368v using only one internal triple rad with 3 fans to water cool both the cpu and an overclocked ATI 5870.
P6T Deluxe v2 board rev:1.02g chipset X58 rev:B03 crossflashed with 'no-throttle' 0006 Bios (more hardware in sig).
Screenshot and some Bios data that can help others:
---------------------------------------------------
CPU Ratio: 21 - BCLK: 215 - PCIE: 100 - DRAM Fr: 1723MHz - UCLK Fr: 3663MHz - QPI Link: 7759MT/s
CPU Volt: 1.375 (1.368 under load) - CPU PLL: 1.80 - QPI/DRAM Volt: 1.375 - DRam Bus Volt: 1.64 - DRam Timings: 7,8,7,21,1N
LLC: Enabled - cpu Amplitude= Auto - *skews: Auto, *spectrums/c1e/VT/TM/EDB/HT/A20M/SpeedStep/C-State: Disabled
http://i224.photobucket.com/albums/d...y/i7oc4500.jpg
Very nice and detailed info, thanks! :up:
This was in my htpc, I slapped a true on it, and it turned out well, I'd say. It loads at 1.344 most of the time, not 1.328v, and it hates llc.
http://img46.imageshack.us/img46/3650/97583664.jpg
may i joint, thx
Watercooled, HT ON
http://i194.photobucket.com/albums/z...linx451388.jpg
Sure, welcome. :)Quote:
Originally Posted by Boyu
And good job everyone! :up:
http://img199.imageshack.us/img199/5967/48ghz.jpg
Cooled w/ a single stage phase change.
4811MHz w/ HT on.
First try using 4 threads on the 870. Will try and lower vcore.
Edit: another run using more mem and less vcore.
1.408v Vcore, 1.30VTT, 1.640v DRam, 1.80v PLL, 1.080v PCH, Gigabyte P55A UD6.
http://img33.imageshack.us/img33/3167/45ghz.png
Can I join:D:D:D? Done with a Mugen II and Ceramique with 27 C ambient .Motherboard is p5e
Updated, and welcome! :yepp:
My dual core contribution:
E8600 Q820A727 5100Mhz + Super Talent Project X DDR3 1800 D9GTR (haven't tested lowest vcore yet, just quick stable run):
http://img710.imageshack.us/img710/1...0stable.th.jpg
http://img94.imageshack.us/img94/598...stable2.th.jpg
Code:Extreme Tweaker
Ai Overclock Tuner [Manual]
OC From Memory Level Up [Auto]
FSB Frequency [537]
CPU Ratio Setting [9.5]
* CPU clock skew [Auto]
* NB clock skew [Auto]
FSB Strap to North Bridge [200]
PCIE Frequency [102]
DRAM Frequency [1790]
DRAM Command Rate [1N]
DRAM Timing Control [Manual]
1st information
CAS# Latency [7]
RAS# to CAS# Delay [7]
RAS# PRE Time [7]
RAS# ACT Time [21]
RAS# to RAS# Delay [Auto]
REF Cycle Time [68]
WRITE Recovery Time [Auto]
READ to PRE Time [Auto]
2nd information
READ to WRITE Delay(S/D) [Auto]
WRITE to READ Delay(S) [Auto]
WRITE to READ Delay(D) [Auto]
READ to READ Delay(S) [Auto]
READ to READ Delay(D) [Auto]
WRITE to WRITE Delay(S) [Auto]
WRITE to WRITE Delay(D) [Auto]
3rd information
WRITE to PRE Delay [Auto]
READ to PRE Delay [Auto]
PRE to PRE Delay [Auto]
ALL PRE to ACT Delay [Auto]
ALL PRE to REF Delay [Auto]
DRAM Static Read Control [Auto]
DRAM Dynamic Write Control [Auto]
> DRAM Skew Control :
DRAM CMD Skew on Channel A [Auto]
DRAM CLK Skew on DIMM A1 [Auto]
DRAM CLK Skew on DIMM A2 [Auto]
DRAM CTL Skew on DIMM A1 [Auto]
DRAM CLT Skew on DIMM A2 [Auto]
DRAM CMD Skew on Channel B [Auto]
DRAM CLK Skew on DIMM B1 [Auto]
DRAM CLK Skew on DIMM B2 [Auto]
DRAM CTL Skew on DIMM B1 [Auto]
DRAM CTL Skew on DIMM B2 [Auto]
Ai Clock Twister [Auto]
Ai Transaction Booster [Manual]
Common Performance Level [7]
Pull in of CHA PH1 [Disabled]
Pull in of CHA PH2 [Disabled]
Pull in of CHB PH1 [Disabled]
Pull in of CHB PH2 [Disabled]
(-- Manual --)
EPU II Phase Control [Auto]
*** Please key in numbers or select voltage!***
CPU Voltage [1,61250]
Load-Line Calibration [Enable]
CPU PLL Voltage [1,5773]
FSB Termination Voltage [1,39...]
CPU GTLVref(0) [+40]
CPU GTLVref(1) [+40]
CPU GTLVref(2) [Auto]
CPU GTLVref(3) [Auto]
NB GTLVref [+30]
North Bridge Voltage [1,69]
DRAM Voltage [Auto]
NB DDRVref [Auto]
DDR3 Channel A Vref [Auto]
DDR3 Channel B Vref [Auto]
South Bridge 1.5 Voltage [1,57...] two or three step up for your RAID
South Bridge 1.05 Voltage [1,09...] two or three step up for your RAID
******************************************
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
Open Case.
Air temp: 17oC.
Cooler: OCZ Cryo-Z
WOW, great job with the e8600 Jor. :up:
lowfat
That`s pretty nice :up:
lots of juice but you got there:p:Quote:
Originally Posted by OC Nub
Yeah it isn't a golden chip but I am happy with the temps. Its a newer batch#3945A936. I am happy with it, I hope to do some nice 3Dbenches with this new rig. Vcore is high but 4500mhz is 4500mhz, and Im having fun.:up:Quote:
Originally Posted by zsamz_
OC Nub what is your cooling and what is the ambient temp to get 75C under load at 4.5Ghz/1.48v?
:yepp: gettin to 4.5 is :up:Quote:
Originally Posted by OC Nub
I am using the XSPC rx360, mcp655, apogee XT block, and an ek multioption res150, in my avatar its hard to see buy there is a window unit AC blowing at the rad.Quote:
Originally Posted by ChaosAD
Congrats friend you did it !!!Quote:
Originally Posted by OC Nub
Cheers :up:
Sergio
Thank you Sergio.
Does anyone have any experience with Core i7 920 D0 batch 3941B138 CPUs?
Try asking here.Quote:
Originally Posted by EnisDonKing
Nice work guys.
Just a reminder to please put your overclocks into the Xtremesystems database I made (make sure you show stability test in SS) - found Here
Add your OC details to the form, then click submit and the database will automatically update with your results. There is a link to the database in the thread I linked you to and
you can download it yourself in various formats as you wish.
According to my 4.4Ghz runs i think that i ll need about 1.55v to run 4.5Ghz HT on 20 Linx runs with temps around 90C. Do you think its safe for 20 runs. I would be able to pass with HT off with less vcore but i consider it cheating :p: