Printable View
Here are my findings so far. Please add mod pictures if you find them.
I don't have time to look vddr mod today.
Vdrop isn't needed with Deluxe. With vcore mod drop is only 0.01V :D
Vcpu:
Attachment 59403
Vmch:
Attachment 59404
Vsb: (Thanks to team Japan)
Attachment 63164
Vcpu PLL: (Thanks to team Japan)
Attachment 63165
Measure points:
Attachment 63166
I HAVE TESTED THESE MODS AND THEY ARE WORKING 100%.
Thanks for sharing SF3D.. i find that CPU PLL voltage and vfsb seems critical for kentsfield overclocking with high fsb.. anyway u can find the vmod for that? :)
thx SF3D :) :)
Anyone found Vdimm already?
Testing and work ok :)Quote:
Originally Posted by Extera
Martin
just right, Thx DEVIL K-ce ;)
Your my hero, might be a noobish question, but witch pin is ground (pin3, left or right pin)? I alway's use a other ground :p:Quote:
Originally Posted by DEVIL K-ce
and witch point is Vdimm messurepoint?
Thanks in advantage
Hi
Modded foto :p:
Also I use PIN 6 and other ground :up:
Martin
where is the vcore read point?
Thanks DEVIL K-ce
Vcore messurepoint is usaly somewere on the mosfets, under the heatsink in this case. I realy need do get into electonica more :)
Vcore monitor work ok from bios, but You can check vcore with DMM under this coil :)
Martin
Thank you
Hi all,please,anyone know the resistance value to do for example 1.9 V?
For example,If you set 1.7 V from Bios how it's the value on the trimmer? 20 kohm? 10? or so?
Hi, The Vdimm monitor point does not seem to work.
Vcore works fine, but I cant readout the Vdimm now to test the Vdimm mod.
Is there a different reading point?
Thanks
Hi
My bad - on this photo is working vdimm monitoring point :)
Martin
I cant get the lead from my dmm under those coils, can anyone let me know if this point reads the same voltage? I checked voltage here and it is 0.01v less than what is set in bios.
is there any way to pencil mod for more vcore as i dont really want to solder my board
if i did solder a variable on is it this one
18-Turn Cermet 50k
An 18-turn cermet preset with slipping clutch (23 mechanical turns), end stops and infinite electrical resolution. Power rating 0.75W at 70C. Max working voltage 315V. Tolerance: ±10%. Temperature coefficient: ±100ppm/C max. Values available: 500‡;,...
i noticed it has 3 pins where does the 3rd pin go?
why Vmch ????
So what kind on results have ppl got from this , is the ~530 wall gone ?
SF3D : Did the MCH mod gain you any thing ? I dont even find I need to use the 1.7 that bios has . 1.55 works for my 4ghz runs .
Has any one Confermed Hemi's other Vcore read point ?
I need a VCore Pencil-Mod to, can anyone help me?
Same mod's for asus p35 mobo, p5k ws ?
Updated the first post. All Vmods are here now!
would the vcore and vdimm mods be the same for p5k-e?
I am trying to confirm if some of these mods are the same for the P5K Prem too. The board layout and components seem identical to the Dlx, but use diff brands.
Can someone with a Dlx measure the PLL and FSB VTT points and tell me what readings you get at minimum BIOS setting for them (not AUTO) and then 1 or 2 steps up? Neither of the voltages I measure on those legs on the Prem ever change no matter what I set the Vpll or FSB Term to in BIOS. No one else here seems to have done the mods on a Prem yet, so I am curious if I just need to look for different measure points on the Prem or if I need to dig further than that.
See my thread here for additional info/pic of the Prem board if you can help out ;)
The answer is yes :yepp:Quote:
Originally Posted by toddm27