3DMark01 Madness by Hollywood & der8auer (Hall of Fame inside!)

Printable View

01-08-2011, 03:47 AM
der8auer

3DMark01 Madness by Hollywood & der8auer (Hall of Fame inside!)

Hello :wave:

Yesterday i met with Hollywood in south-west Germany for some 3Dmark2001 action :up: Our goal was to gain two good SLI scores and maybe also Single-GPU.

Hardware:

2x E8600 (Q822A435)
4x Rampage Extreme
6x MSI GTX275 Lightning (vMEM, OCP, vGPU Mod)

90l LN2 :yepp:

http://extreme.pcgameshardware.de/at...e-img_0001.jpg

http://extreme.pcgameshardware.de/at...e-img_0004.jpg

First we set up a system using my best RE and my E8600 (pretested here: Link). I don't know what happened but i coudln't boot the system. The LCD poster just showed "PWR_OFF". So i had to use another RE which was completely untested. Unfortunately it was crappier than i expected :D

Anyway the System was running a bit later. We had no Software-Tool to raise the Voltage of two Lightning GPUs so we had to do the hardmods. Sadly we coudln't go over 1,35vGPU. Everything else above straightly caused OVP. But it was enough for 975 MHz on both cards. :up:

Result:

12th on HWBot: http://hwbot.org/community/submission/2102137_

Link to the Screenshot of the Result

Later we tried to get a good single GPU result. CPU passed 01 at 6411 MHz and the GPU at 1350MHz. Unfortunately we coudln't do a complete run because we were unable to boot after a bit :down: Anyway we know the components are capable and we can maybe do the run in a bit :up:

And finally some impressions of the day :up:

http://extreme.pcgameshardware.de/at...e-img_0013.jpg

http://extreme.pcgameshardware.de/at...e-img_0027.jpg

http://extreme.pcgameshardware.de/at...e-img_0044.jpg

http://extreme.pcgameshardware.de/at...e-img_0042.jpg

http://extreme.pcgameshardware.de/at...e-img_0044.jpg

http://extreme.pcgameshardware.de/at...e-img_0048.jpg

http://extreme.pcgameshardware.de/at...e-img_0046.jpg

http://extreme.pcgameshardware.de/at...e-img_0052.jpg

http://extreme.pcgameshardware.de/at...e-img_0053.jpg

http://extreme.pcgameshardware.de/at...e-img_0054.jpg

http://extreme.pcgameshardware.de/at...e-img_0066.jpg

http://extreme.pcgameshardware.de/at...e-img_0067.jpg

http://extreme.pcgameshardware.de/at...e-img_0073.jpg

http://extreme.pcgameshardware.de/at...e-img_0074.jpg

http://extreme.pcgameshardware.de/at...e-img_0077.jpg

Maybe the Board didn't like the name of the settings? :rofl:

http://extreme.pcgameshardware.de/at...e-img_0072.jpg

:clap:
01-08-2011, 03:52 AM
massman

:up: :up: :up:

Did you have problems with two sli bridges connecting the cards? Last time I tried that I had screen corruption.

Oh, and 6x GTX275 Lightning = :shocked:
01-08-2011, 03:54 AM
der8auer

Thanks :)

We had no difference between one and two SLI bridges.

Actually we had 7 Lightnings but i was to lazy to modify the last one :D
01-08-2011, 04:15 AM
miahallen

Very nice run guys....well done :clap:

Good luck next time :D
01-08-2011, 05:37 AM
Don_Dan

Nice work guys! :up:

7 Lightnings -> me = jealous :rofl:
01-08-2011, 07:40 AM
Q56_Monster

Great work guys! Is that a custom vRAM/vreg plate you have on the 275's? What do you have under it, regular thermal paste?
01-08-2011, 08:03 AM
der8auer

Thank you!

No, that's the retail cooler by MSI. Here you can find pics of it: http://www.techpowerup.com/reviews/M...ghtning/4.html
01-08-2011, 08:23 AM
Billy-The-Kid

First of all congratulations for the score! Too bad not having a cpu (or board) to followed!
What voltage you used to achieve 1350MHz on a single card?
01-08-2011, 08:51 AM
*Hollywood*

Quote:

Originally Posted by Billy-The-Kid

First of all congratulations for the score! Too bad not having a cpu (or board) to followed!
What voltage you used to achieve 1350MHz on a single card?

We had it running at 1.6 vGPU, 2.15 vMem.
There should be a lill bit more MHz in that card. :)
Tested some other cards with same voltage, but this one is rly great.

EDIT: And hello to you guys at XS, my first post over here! ;)

Hollywood
01-08-2011, 11:10 AM
Billy-The-Kid

I have two but only one has tested on ln2 and not come near it :( I'll test the other one of this dayt´s ... What soft used to raise the voltage? Does not work in sli?
01-08-2011, 11:42 AM
der8auer

We used the MadMatrix GTX285 tool which doesnt work in SLI...

And thanks :)
01-08-2011, 12:11 PM
*Hollywood*

Quote:

Originally Posted by Billy-The-Kid

I have two but only one has tested on ln2 and not come near it :( I'll test the other one of this dayt´s ... What soft used to raise the voltage? Does not work in sli?

Today i've testet 2 more Lightnings. These cards behave a lill different.
One of these got no CB. But it just run 1280/1350.
The other one got a CB at around 160°C and completet the benchmark at the same speed as the other one.
Will test CB on my best card tomorrow.
1350 was at around 140°C. I am limited by my GPU pot.
Could not keep the temps stable and low douring a test.
01-08-2011, 12:12 PM
Linuxfan

Quote:

Originally Posted by der8auer

First we set up a system using my best RE and my E8600 (pretested here: Link). I don't know what happened but i coudln't boot the system. The LCD poster just showed "PWR_OFF". So i had to use another RE which was completely untested.

Love the frost pictures! Good luck trying again for single GPU!
Do you have any clue why the REX wouldn't start? Mine gave me trouble also this week and will not start, the screen says PWR_OFF as well when I boot it. Doesn't post on air or SS. :down:
01-08-2011, 12:25 PM
der8auer

Thx :)

I got no idea. The board runs fine now... No clue what caused the problem.

Just played arround with GTX280 on LN2 =)
http://hwbot.org/community/submission/2102626_

1160MHz GPU is not too bad :D
01-08-2011, 12:45 PM
*Hollywood*

Quote:

Originally Posted by Linuxfan

... Good luck trying again for single GPU!
...the screen says PWR_OFF as well when I boot it. Doesn't post on air or SS. :down:

THX! :up: We had semilar problems yesterday.
Today my 2nd REX just starts on the first try....
Guess that's the asus rampage extreme special fail feature....
01-08-2011, 01:04 PM
Linuxfan

Quote:

Originally Posted by der8auer

Thx :)

I got no idea. The board runs fine now... No clue what caused the problem.

Just played arround with GTX280 on LN2 =)
http://hwbot.org/community/submission/2102626_

1160MHz GPU is not too bad :D

Nice AM3 run! Thats pretty sweet for only 1.68v CPU. :D
01-08-2011, 01:13 PM
der8auer

Thanks :D

Yes it's a insane CPU but as you read on the result - i can't go higher with the voltage. I don't know what causes the problem :shrug:

e.g. benching wPrime:

CPU runs smooth at 1,68vCore but if i go at 1,7 or 1,75 (just higher) the system instantly shuts down if it's on load. Means i click to start the 32m run and -> black screen and system is shut down...

I also tried 06 CPU Test and exactly the same problem. It starts to load the test but instead of running i get black screen an system shuts down.

Any ideas about that?
01-08-2011, 02:37 PM
TiN_

OCP mayba.
01-08-2011, 03:18 PM
der8auer

It looks like OCP yes but is there like an OCP mod for the 4-Way board? :confused:

edit: Or is there something in BIOS i've to set and i'm too stupid to see it?
01-08-2011, 03:46 PM
GLENBOY

i head the same batch cpu q822a435 and at the time had a maximus board and it was exactly the same i thought it was the motherboard at the time but maybe it was the cpu, i had it on a ss at the time highest volts on mine was 1.7 and 1.72 either no boot or boot to black screen just my 2 cents worth
01-08-2011, 04:06 PM
Billy-The-Kid

Quote:

Originally Posted by der8auer

We used the MadMatrix GTX285 tool which doesnt work in SLI...

And thanks :)

:) I use one similar....but I see I have the same problem!

Edit: Problem solved!!!
01-08-2011, 04:28 PM
der8auer

Quote:

Originally Posted by GLENBOY

i head the same batch cpu q822a435 and at the time had a maximus board and it was exactly the same i thought it was the motherboard at the time but maybe it was the cpu, i had it on a ss at the time highest volts on mine was 1.7 and 1.72 either no boot or boot to black screen just my 2 cents worth

Interesting to know, thanks! Because i kinda doubt that there is an OCP of the board or :shrug:
01-09-2011, 02:23 AM
fuzz3l

Quote:

Originally Posted by Billy-The-Kid

:) I use one similar....but I see I have the same problem!

Edit: Problem solved!!!

What did yo do?

@der8auer:
I got the same with my Q822A435, one day it boots normal and on SS the highest volt was 1.6v and now the cpu is dead....i dont know why...:shrug::shrug:

_
Christian
01-09-2011, 02:44 AM
MaJ0r

Awesome scores, clocks and preperation :clap: Congrats:up:
01-09-2011, 10:43 AM
Billy-The-Kid

Quote:

Originally Posted by fuzz3l

What did yo do?

Christian

I'm doing a program all beautiful :D after I provide! :up:
01-09-2011, 01:43 PM
crio

Impressive score Roman......Well done buddy
01-09-2011, 02:56 PM
der8auer

Quote:

Originally Posted by MaJ0r

Awesome scores, clocks and preperation :clap: Congrats:up:

Thank you :)

Quote:

Originally Posted by crio

Impressive score Roman......Well done buddy

Thanks mate :up: