Foxconn BloodRage Shared BIOS Settings
Greets folks here's your place for bios settings using BloodRage pls share your bios setting using this format this will be helpfull for all of us thx for taking time to share
CPU & Batch (XXX)
RAM Model (XXX)
Bios Ver: Quantum BIOS (XXX)
CPU Features
PPM :
EIST :
CxE :
Execute Disable Bit :
Virtualization :
Hyper Threading :
Active Processor Cores :
Memory Settings
Memory Controller Settings
IMC Configuration :
Channel Congifuration :
Channel Interleaving :
Rank Interleaving :
Memory Timings
Extreme Memory Profile XMP :
Memory Profile Select :
DRAM Timing Control :
tCL (CAS Latency) :
tRCG (RAS to CAS Delay) :
tRP (RAS Precharge) :
tRAS (Precharge Delay) :
CR (Command Rate) :
tRFC (Refresh Cycle Time) :
tWR (Write Recovery Time) :
tWTR (Write to Read Delay) :
tRRD (RAS to RAS Delay) :
tRTP (Read to Precharge) :
All Voltage Settings
CPU Voltages
CPU Core Voltage :
CPU Target Core Voltage :
CPU Vdroop Compensation :
CPU VTT (UnCore) Voltage :
1.8 PPL Voltage Setting :
CPU Clock Amplitude Ctrl :
Memory Voltages
DRAM Voltage :
DIMM1 Vref CA (Addresses) :
DIMM1 Vref DQ (Data) :
DIMM2 Vref CA (Addresses) :
DIMM2 Vref DQ (Data) :
DIMM3 Vref CA (Addresses) :
DIMM3 Vref DQ (Data) :
Chipset Voltages
X58 IOH Core Voltage :
X58 IOH VCCA 1.1V :
X58 IOH VCCA 1.5V :
ICH10 SB Voltage :
OC Gear : Skipping this part
CPU Turbo :
System Turbo :
Clock Speed Control Center
CPU Bclock (FSB) :
QPI Link Fast Mode :
QPI Multiplier :
QPI Target Speed :
CPU Core Multiplier :
CPU Core Target Speed :
CPU Uncore Multiplier :
CPU Uncore Target Speed :
Memory Bus Multiplier :
Memory Bus Target Speed :
CPU Clock Skew :
IOH Clock Skew :
My setting for 1600 I have more for 2000
CPU & Batch (3849A866)
RAM Model (Mushkin 998708 2000mhz)
Bios Ver: Quantum BIOS P06 and G25
CPU Features
PPM : Enabled
EIST : Enabled
CxE : Disabled
Execute Disable Bit : Disabled
Virtualization : Disabled
Hyper Threading : Diabled
Active Processor Cores : ALL
Memory Settings
Memory Controller Settings
IMC Configuration :Enabled
Channel Congifuration :Independent
Channel Interleaving :6
Rank Interleaving :4
Memory Timings
Extreme Memory Profile XMP : Disabled
Memory Profile Select :auto
DRAM Timing Control :Manual
tCL (CAS Latency) :6
tRCG (RAS to CAS Delay) :6
tRP (RAS Precharge) :5
tRAS (Precharge Delay) :auto
CR (Command Rate) :1T
tRFC (Refresh Cycle Time) :auto
tWR (Write Recovery Time) : auto
tWTR (Write to Read Delay) : auto
tRRD (RAS to RAS Delay) : auto
tRTP (Read to Precharge) : auto
All Voltage Settings
CPU Voltages
CPU Core Voltage :+30mV
CPU Target Core Voltage :1.26750
CPU Vdroop Compensation :Enabled
CPU VTT (UnCore) Voltage :+80
1.8 PPL Voltage Setting :1.800
CPU Clock Amplitude Ctrl :.800
Memory Voltages
DRAM Voltage :1..65
DIMM1 Vref CA (Addresses) :.500
DIMM1 Vref DQ (Data) :.500
DIMM2 Vref CA (Addresses) :.500
DIMM2 Vref DQ (Data) :.500
DIMM3 Vref CA (Addresses) :.500
DIMM3 Vref DQ (Data) :.500
Chipset Voltages
X58 IOH Core Voltage :1.10
X58 IOH VCCA 1.1V :1.108
X58 IOH VCCA 1.5V :1.506
ICH10 SB Voltage :1.506
OC Gear : Skipping this part
CPU Turbo : Always On
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) : 200
QPI Link Fast Mode :
QPI Multiplier : x18
QPI Target Speed : 3605(7.2GT/s)
CPU Core Multiplier : x18
CPU Core Target Speed :3605
CPU Uncore Multiplier : 18
CPU Uncore Target Speed : 3609
Memory Bus Multiplier : 8
Memory Bus Target Speed : 1604
CPU Clock Skew : Ops
IOH Clock Skew :Ops
HT Enabled (Not that I use it but it works)
CPU & Batch (3849A866)
RAM Model (Mushkin 998708 2000mhz 8-8-7-24-1T)
Bios Ver: Quantum BIOS (G25)
CPU Features
PPM : Enabled
EIST : Enabled
CxE : Disabled
Execute Disable Bit : Enabled
Virtualization : Disabled
Hyper Threading : Enabled
Active Processor Cores : All
Current Feedback Override: Enabled (added this one for HT otherwise Multi Drops)
Memory Settings
Memory Controller Settings
IMC Configuration : Enabled
Channel Congifuration :Independent
Channel Interleaving :6
Rank Interleaving :4
Memory Timings
Extreme Memory Profile XMP : Disabled
Memory Profile Select :auto
DRAM Timing Control :Manual
tCL (CAS Latency) :6
tRCG (RAS to CAS Delay) :6
tRP (RAS Precharge) :5
tRAS (Precharge Delay) :auto
CR (Command Rate) :1T
tRFC (Refresh Cycle Time) :Auto
tWR (Write Recovery Time) : Auto
tWTR (Write to Read Delay) : Auto
tRRD (RAS to RAS Delay) : Auto
tRTP (Read to Precharge) : Auto
All Voltage Settings
CPU Voltages
CPU Core Voltage : +40mV 1.27750 Cpuz reports 1.26, and jumps to 1.328v under load CPUZ-1.51, Hottest core 74C. coolant @ 32-33 C
CPU Target Core Voltage : 1.27750
CPU Vdroop Compensation : Enabled
CPU VTT (UnCore) Voltage : +200mV
1.8 PPL Voltage Setting : 1.856
CPU Clock Amplitude Ctrl : .800
Memory Voltages
DRAM Voltage :1.65
DIMM1 Vref CA (Addresses) :.500
DIMM1 Vref DQ (Data) : :.500
DIMM2 Vref CA (Addresses) : :.500
DIMM2 Vref DQ (Data) : :.500
DIMM3 Vref CA (Addresses) : :.500
DIMM3 Vref DQ (Data) : :.500
Chipset Voltages
X58 IOH Core Voltage :1.10
X58 IOH VCCA 1.1V :1.108
X58 IOH VCCA 1.5V :1.506
ICH10 SB Voltage :1.506
OC Gear : Skipping this part
CPU Turbo : Always on
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) : 200
QPI Link Fast Mode : Enabled
QPI Multiplier : X18
QPI Target Speed : 3605
CPU Core Multiplier : X18
CPU Core Target Speed : 3605
CPU Uncore Multiplier : X18
CPU Uncore Target Speed : 3609
Memory Bus Multiplier : X8
Memory Bus Target Speed : 1604
PCI Express Bus Clock : 100
CPU Clock Skew : Ops
IOH Clock Skew : Ops
:up:
Oh and if I enable the AutoShut down. The readings go crazy... All voltages go to 4.06 not acutally go there but reports as such, and does not happen all the time random but only happens if I set it....
Crazy Chit...
