XS HWBot Team

Printable View

Show 100 post(s) from this thread on one page

10-07-2010, 09:46 AM
Linuxfan

Going out to get 55L of LN2 for the 980x 3003B475...
Wish me luck!
10-07-2010, 10:07 AM
Don_Dan

Quote:

Originally Posted by Linuxfan

Going out to get 55L of LN2 for the 980x 3003B475...
Wish me luck!

Good luck! :up:

Many nice scores have been posted today, especially Linuxfan has been very busy! Good work everyone! :)

http://img830.imageshack.us/img830/3...ber6th2010.jpg
10-07-2010, 06:09 PM
Linuxfan

LN2 is here are waiting. Prepping OSes and insulating in the morning then BENCHING! :D
Thanks for the update Daniel.
The laptops were fun to test. Actually still have some more CPU testing to do. :up:
10-08-2010, 09:59 AM
ZenEffect

Quote:

Originally Posted by linuxfan

going out to get 55l of ln2 for the 980x 3003b475...
Wish me luck!

push it! :D :D :D
10-08-2010, 10:28 AM
Linuxfan

5 Attachment(s)

Quote:

Originally Posted by ZenEffect

push it! :D :D :D

Insulated and just about ready to roll! :up:
10-08-2010, 03:05 PM
BenchZowner

Friends don't let friends use kneaded eraser.

3 layers of Conformal spray & vaseline.
Much better in every single aspect.
10-08-2010, 04:00 PM
chew*

Quote:

Originally Posted by BenchZowner

Friends don't let friends use kneaded eraser.

3 layers of Conformal spray & vaseline.
Much better in every single aspect.

conformal ftw, btw your buddy trans am has commenced operation corrupted by chew* and on his way up, should be here in an hour or so :)
10-08-2010, 05:25 PM
GeorgeStorm

Whats wrong with eraser?
And btw linuxfan, lovely looking setup :)
What pot you using?
10-08-2010, 05:29 PM
ScottALot

Linuxfan, you hear about the new Mushkin sticks? It's like gluing a Redline to a Ridgeback... because they are... REDLINE RIDGEBACK!
10-08-2010, 05:53 PM
Linuxfan

1 Attachment(s)

Quote:

Originally Posted by BenchZowner

Friends don't let friends use kneaded eraser.

3 layers of Conformal spray & vaseline.
Much better in every single aspect.

Quote:

Originally Posted by chew*

conformal ftw, btw your buddy trans am has commenced operation corrupted by chew* and on his way up, should be here in an hour or so :)

Gotta do conformal just haven't jumped on the board yet. ;)

Quote:

Originally Posted by GeorgeStorm

Whats wrong with eraser?
And btw linuxfan, lovely looking setup :)
What pot you using?

Thanks George!
Eraser doesn't insulate the board as well as a complete coating of rubber and you have to install it each time you want to bench.
The CPU pot was made by Ryba.

Here's what I was able to get today... I'm sure there's more clocks in the CPU though still feeling it out.
Superpi32M, 1M, and pifast next. :up:
10-09-2010, 12:41 AM
BenchZowner

Kneaded eraser is good for "low" temp benching, as in temps being hold nearly statically in the -70 to -90C range.
For any kind of long term benching with seriously low temps ( -120 and higher ) kneaded eraser is only going to cause issues, it's going to get moist, and in an hour or so you'll be having water dripping in every corner of it.
10-09-2010, 02:16 AM
GeorgeStorm

Ah fair play
Even in the -30 to -40 range I sometimes get bleeding, but othertimes I don't, not sure why
Haven't got that cold yet (sadly :( ) so I guess I'll just have to find out.
10-09-2010, 02:40 AM
Linuxfan

Quote:

Originally Posted by BenchZowner

Kneaded eraser is good for "low" temp benching, as in temps being hold nearly statically in the -70 to -90C range.
For any kind of long term benching with seriously low temps ( -120 and higher ) kneaded eraser is only going to cause issues, it's going to get moist, and in an hour or so you'll be having water dripping in every corner of it.

I was at -182 for a few hours with this chip... The room was pretty dry(basement that is temperature controlled) so the condensation wasn't so bad. It did get wet though. :down:
10-09-2010, 07:49 PM
ZenEffect

xs is coming up on the single core challenge! great job you guys!
10-10-2010, 05:03 PM
systemviper

Quote:

Originally Posted by Linuxfan

I was at -182 for a few hours with this chip... The room was pretty dry(basement that is temperature controlled) so the condensation wasn't so bad. It did get wet though. :down:

nice setup, seems your all over the place :surf:
10-10-2010, 07:56 PM
Linuxfan

Quote:

Originally Posted by systemviper

nice setup, seems your all over the place :surf:

:D Thanks
I was prepped and going to do some more heavy testing today but got stopped by a CBB with the cascade running -120oC need to figure out how to bypass this then I'll be running again. :up:
10-11-2010, 12:45 AM
BenchZowner

What are you running Linuxfan ?
10-11-2010, 04:33 AM
Linuxfan

Quote:

Originally Posted by BenchZowner

What are you running Linuxfan ?

Was running a lapped Q6600 G0 with some Crucial Ballistix D9 mem in a EP45-UD3P rev 1.0 board but had a CBB. Wasn't sure where the hot gas bypass valve was so I just had to shut 'er down. :(
Found it and am ready to roll today.
Will either test out the Q6600 on Cascade, Q9450 for the gold(and hope it doesn't CB at -120oC) or slap a Ceader Mill CPU in my DFI P35 T2R board to try for some 7ghz+ CPU-Z action on LN2(either the 347, 356, one of the 631s or a 651). :up:
Too much to do and too little time. ;)
10-11-2010, 06:15 AM
BenchZowner

Try lowering the CPU PLL Voltage ( sub-specs ) it may lower the CBB & CB.
10-11-2010, 09:25 AM
Don_Dan

In the most recent stage of the ASUS 1156 Overclocking Championship, two of our members entered Top 10, chew* and FUGGER came in 5th and 7th respectively. Zeneffect made 15th place in this stage!
Good luck for the next stage! :up:

In HWBot's OC Challenge October, thanks to some excellent submissions by chew* and G.Foyle, the team is currently ranked 2nd in the overall ranking, while still holding the record in the 3DMark Vantage stage. Nice work! :)
10-11-2010, 12:21 PM
ZenEffect

Quote:

Originally Posted by Don_Dan

In the most recent stage of the ASUS 1156 Overclocking Championship, two of our members entered Top 10, chew* and FUGGER came in 5th and 7th respectively. Zeneffect made 15th place in this stage!
Good luck for the next stage! :up:

In HWBot's OC Challenge October, thanks to some excellent submissions by chew* and G.Foyle, the team is currently ranked 2nd in the overall ranking, while still holding the record in the 3DMark Vantage stage. Nice work! :)

it appears in overall standings, we have beat out to oca guys for the time being as well. :yepp:
10-11-2010, 12:42 PM
Linuxfan

Quote:

Originally Posted by ZenEffect

it appears in overall standings, we have beat out to oca guys for the time being as well. :yepp:

Nice work guys! :clap:
10-11-2010, 08:55 PM
Linuxfan

1 Attachment(s)

Tested the Q9450 on my EP45-UD3P rev. 1.0 board with the cascade...
Seems like the chip doesn't like to be overfrozen, didn't get much farther with clocks than my runs with the EP45T-UD3LR board and the SS unit. Seemed like it had a coldslow or something though, results started getting super slow at high speeds. :shrug:
Might try on air tomorrow and see what I can figure out.
Cascade runs great. :D
10-12-2010, 05:46 PM
trans am

me and chew this past weekend. massman wont let me submit in the oct. contest with his card. but for the record.
http://hwbot.org/community/submissio...870_9827_marks
10-12-2010, 06:00 PM
Linuxfan

Quote:

Originally Posted by trans am

me and chew this past weekend. massman wont let me submit in the oct. contest with his card. but for the record.
http://hwbot.org/community/submissio...870_9827_marks

The score Chew* got was higher so it wounldn't make a difference at all if you posted that score.
Its great that you were able to bench with Brian this last weekend, I'm sure it was a good experience. :up:
Why don't you try some PCMark sometime with your three SSDs? I"m sure that'd be fun. :D

Show 100 post(s) from this thread on one page