230MHz at the moment...
not max out yet... :hehe:
Printable View
230MHz at the moment...
not max out yet... :hehe:
tedy, i'm pretty sure thats it, becuase look at one of the reviewers of the product, shroomalistic.
Thats the stuff.
My 2x256 speed premiums were pretty good TT. 1 stick does 264 and 1 does 267.Quote:
Originally Posted by tictac
These are on brainpower pcb. DO yours have BP too?
didn't alonso say that they arent BP pcb?
nope... ;)Quote:
Originally Posted by trans am
sorry, they are UTT sticks, 44d, not bh-5 based sticks. I'm still expecting alot though.
I don't know if it has been noted before - this thread is huge!! - but not all Speed Premiums come with a BP pcb...I think that pre-UTT SPs came with BP but newer sticks carrying UTT don't.
Reviews of non-UTT SpeedPremium with BP pcb:
http://www.techpowerup.com/reviews/TwinMOS/SpeedPremium
http://www.hardwarezoom.com/viewcont...D=228&PageNo=1
Review of UTT SpeedPremium without BP pcb:
http://www.pcstats.com/articleview.cfm?articleID=1724
My SP carry the same pcb as the ones in the PCStats.com review above. It's identical to the pcb of the new BH5 Twinmos. Check it out here:
http://www.xtremesystems.org/forums/...ad.php?t=53645
Maybe Alonso can clear things up..
none of the latest SP has BP pcb. but i remember some early UTT sticks having BP pcb (maybe i'm confusing with the non-UTT ones) and didn't oc higher than the usual KO pcb one's.
AFAIK,
all TwinMOS AA4T is not on BP PCB
only some AADT got BP PCB - which is not Winbond utt tho :slap:
running at 230MHz ... :)
still burning in ;)
http://www.tictac.katrourke.com/pic/230-338.gif
what system tictac ? 230 not so good.....bump vdimm 3.3v and 245 :)
has anyone else tried the new DFI UT 250gb bios?
i shaved a stable second off my PI time:) now at 33/s with TREF=1560, DRAM BANK INTERLEAVE...Enabled :toast:
Question... what the FK is "auto-preharge". It is ON by default in all NForce2 bios's. NForcetweaker lets us turn it off. Anyone know the PCR address for this setting? I'd love to have WPCRSET turn it off, as NFtweaker is incompatible with MBM. There is no setting for it in the DFI NF2 bios, which is ashame since everything else IS there ;-)
The SPD on these rams says it DOES NOT support "autoprecharge" and sure enough turning it OFF gets a few more Mhz out of the ram, and no loss in bandwidth.
BTW Im sitting on the SP page @ Newegg refreshing all day hoping to catch the release.
Further stability testing....using NF7-S 3.2Vdimm, Im very tired now.... on all 4 sets. My original MIRACLE set week5-2005, 3 other sets are week3-2005, one set has a bad stick that gives a 1bit error in memtest regardless of settings...definitely single bad chip on it, so RMA for that pair.
The SO SO sets get 230-5Mhz's with 3.2Vdimm, 1T but start to get errors and arent Prime-stable above this. 2T gets us to 240Mhz or just beyond.
The miracle set gets 238Mhz 1T on this test setup (245Mhz on DFI w/3.48Vdimm). The higher VDimm on DFI got memtest to pass higher on the other 2 sets (not counting bad set anymore) but actualy 3D/Prime testing showed the extra voltage didnt help.
The first pr I got and call "miracle" 1T/2T had no effect on results, making me think it would but at a FSB above my chipset's ability to reach and see it.
Research continues.... hope I can bag a pr of SP's today.
oh my god....
my board can't run with vdimm 3,48....
just 3,2V...
...
wowww...that's great man..!!!
WTG AcidBaby ! :toast:Quote:
Originally Posted by aCidbAbY
I just got my TwinMOS. The code on the chips is
0506D
TMD7608F8E501
Anyone know if they are UTT/any good? They dont seem to be so far.
Great results bro... I am running the same BIOS. Gained me over a minute in SuperPI32mb :DQuote:
Originally Posted by aCidbAbY
Do you get a million errors with Interleaving Disabled?
the new bios has the +3.3v rail mod?
Can someone post or PM me the url to get it?
acid PM'd this to me...Quote:
Originally Posted by BeSaiD
Quote:
Originally Posted by aCidbAbY
Quote:
Originally Posted by Rabbi_NZ
i got this from KLISP* :toast: thx KLISP...
0448D TMD7608F8E50D
Are these chips UTT or just plain crap?
check the PN number on the sticker :hehe:Quote:
Originally Posted by Highland3r
not chip no on the chip :slap:
Supposdly the part number ends AADT so no UTT it seems :(
Well, don't slap him that fast. The info he gave is enough! ;)Quote:
Originally Posted by tictac
The D in "0448D TMD7608F8E50D" indicates that these chips are not Winbond based. If they were Winbond based, there would be a 4 in place of the D. :toast: ;)
Edit: Hmm, not fast enough, but perhaps my info helps some other people.