Quote:
Originally Posted by isp
woopty woop woop :toast: EnJOy>>> http://forums.extremeoverclocking.co...&postcount=848
Printable View
Quote:
Originally Posted by isp
woopty woop woop :toast: EnJOy>>> http://forums.extremeoverclocking.co...&postcount=848
Yeah that just takes me to tictacs post. Thanks I'll use that then...
edit: haha, i'm such a noob i need sata slots 3&4
Running a Palermo 2800+ at 2.2ghz for now, rock stable, getting higher seems to be instable... probably something I missed.Quote:
Originally Posted by loonym
I have got CPU-Z Validation at 2.6ghz though...
http://valid.x86-secret.com/show_oc?id=18549
x86-secret seems to be down right now...
just a (short) question :
*Does every "DFI LANPARTY UT nforce3 motherboard" reach the 300mhz HTT ?
because i tested with mine, and i reached 265~270mhz..but nothing higher...
i tested with ch-5 ram wich is able to run 250mhz @ 2-2-2-5 @ 3.16vdimm...
(i use the modded bios > up to 4vdimm)
*When i set 3.3Vdimm, my system resets the bios to 2.5vdimm > what can cause this 'strange' problem ?!
my system : http://pc.naar.be (choose the amd64 2800+ setup)
greetz
brecht
(sorry for my bad english.. i'm from belgium)
You can always try a divider... and my board can reach 325mhz HTT but the CPU can't handle that stably.
So lower your CPU multiplier and change the RAM Divider, then see how high it goes.
i triedQuote:
Originally Posted by Borgschulze
lowering the ram divider
lowering the cpu multiplier
i set my LDT to 1x
...
ram timings > should it be at auto ? or can i set my CL2 timings (with my divider active..)
UPDATE :
i can set 300mhz in bios..
and ram with divider..
LDT @ 1x
MP @ 4x
vChipset @ 1.89v (set at 1.9v)
but now...
i get an error
--------------------------------------------------------------
NVIDIA RAID IDE ROM BIOS 4.66
Copyright (c) 2004 NVIDIA Corp.
Detecting array ...
_
---------------------------------------------------------------
> thats the error...
(i have a 7200 rpm hdd (ata133))
You will need to use a divider above 260+ likely.Quote:
*Does every "DFI LANPARTY UT nforce3 motherboard" reach the 300mhz HTT ?
because i tested with mine, and i reached 265~270mhz..but nothing higher...
i tested with ch-5 ram wich is able to run 250mhz @ 2-2-2-5 @ 3.16vdimm...
(i use the modded bios > up to 4vdimm)
Your PSU's +3.3v supply is not high enough for the motherboard to be able to output more than approximately 3.2v. You will need to increase the +3.3v supply to increase above 3.2v in the bios.Quote:
*When i set 3.3Vdimm, my system resets the bios to 2.5vdimm > what can cause this 'strange' problem ?!
Yes, set the timings for your RAM manually, do not let the BIOS do it, it tends to mess up my timings at least...
Set the LDT to 3x, and prepare to tweak alot till you get it stable.
how can i reach the 300mhz HTT..
i still get the Nvidia Raid error, while all RAID configs are disabled :(
i use :
*1 ata hdd (ata slot 1)
*1 cd-drive (ata slot 2)
where's the problem ? :(
Yes i get the nv raid error also..im looking to oc my 3000+ DTR but cant get past 240 fsb....this is making me sad :(
This is what I can get prime95 stable on my A64 mobile 3200+ CH with a gig of OCZ 3700EB, and water on the cpu:
250Mhz x 10 @1.78v - 1T ; 3-3-3-8 @ 3.1v
Other than minor tweaks and trying to lower the multi (I can't get over 270 with 1gb of EB and reasonable settings anyhow), I think I have it maxed for the moment. I will try to tighten my ram settings some more. I have tried to get it stable at 3-3-2-8, but its a no go.
I followed that "ideal" OC settings for the board on some other thread (dfi-street?, I forget). Does this seem ok to you guys? Any tips for getting more out of the cpu or tighter timings?
Now for some reason when I took apart my old system to clean it all out because of the dust it was working fine before hand... After I put everything back in it stopped POSTing...what could have happened? Or what did I do to it?
Does anyone have any links to old bios files? I found a disk with one labeled: N32LD128
not sure how old it is.
thanks
Guys, my 3700EB just failed on me (one of the sticks). Since it is discontinued, I am wondering what you guys would recommend in the new OCZ line that would be at least as good? What is an acceptable replacement given that it no longer exists?
Thanks