Printable View
Quote:
Originally Posted by GravediggA
Sweet, thanks big time dude, i just mesured mine, im 1.62v...heres the thing, my BIOS is set to 1.55v with + 10%....so thats the highest this board will go, thats not too high for a 90nm core is it? what voltage do other 90nm users use?
since its 1.4v stock.. my temps look good an its runn good..
For "normal" overclockers... is it safe to do the vdimm like this?
http://www.lejabeach.com/MSIK8N/VdimmMod/k8nneo2-4.jpg
what are the differences for pc_ice way?
thanks a lot
_zZz_
Hi, I'm currently running a Winchester 3000+ at 295x9. BIOS is set to 1.55V+10%, CPU-Z says about 1.61-1.63V under load but I'm reading 1.39V idle and 1.35V load from that mosfet! :confused:Quote:
Originally Posted by GravediggA
It's semi-stable at this speed, I can play CS:Source indefinitely but Superpi fails 32M test after about 6 minutes. Is the Vcore really that low?
[Edit] One more thing, using clockgen I can set the VID to anything equal to or below 1.45V but anything higher (goes up to 1.55V) and it just stays at 1.45V. Strange.
that just makes it 3.3v right? I was thinking of getting a DDR booster but my memory like 3.0v, (TCCD) so i was thinking ill try a 3.3v mod and see if it likes that, if it dose ill go with it.Quote:
Originally Posted by _zZz_
it makes Vdimm = Vio.. so u can change the 3.3v line of the power supply... :)
_zZz_
what do you mean you can change the PSU 3.3v line? Your talking about a sence wire mod right? Not in the bios?Quote:
Originally Posted by _zZz_
if your psu has pots on each rail like the ocz powerstream psu's - or if you install the pots your self ;)
ohh ok, yea my PSU has pots, i put them there myslef :)
I jsut didnt understand what you were sayin..
For the VDD mod, there are 2 solder pads for both the red and brown wires. Do I solder the wires to the pads closest to the SATA ports or do I need to bridge the solder pads and attach the wires. It is hard to tell from the picture.
http://xtremesystems.org/forums/atta...chmentid=17105
probably not ;)Quote:
Originally Posted by ilgreco1974
Hi out there .... Have a question about the Vdimm mod for the K8N Neo 2
Here we can see the default mod ...
http://www.lejabeach.com/MSIK8N/VdimmMod/k8nneo2-4.jpg
And here You can see the Mod for the MSI K8T Neo2-F done for a friend of my.
http://home.tiscalinet.ch/respawn/wh...2/IMG_0012.JPG
U can see, i soldered direktly to the RamSlots. Will this work for the K8N Neo2 too, or have I to use the Capa Mod ?
i've done the one on the first picture and it works great :)
One other question ... i have read the K8N Neo2 tips and tricks guide .... there is an informnation wich is telling me the OCZ Booster will work to 4V on Slot 4
The OCZ Homepage just tells me the Booster will only work to 3.4V for this Board.
Wich information is correct ?!?
the one here of course :P
this board tracks the vtt correctly,so theres no problem on it
_zZz_
I've got 2 questions:
1) Pot for VDD mod should be 20k right? To increase voltage I need to lower the resistance?
2) Can I use JC11 (chassis intrusion jumper) to plug my 3.3V vio mod on it? So I can turn it on and off.... using a jumper :D
Quote:
Originally Posted by adslegend
Hi everybody:
My first post ;) (from Spain)
I get same problem that adslegend, CPU-Z says 1.600 and mosfet read 1.39 idle and 1.35 load. If I put 1.40 bios and CPU-Z says 1.400-1.39, mosfet read is 1.20 :confused: . Is posible that reading point of vcore was other point, what??
Thanks
Hey ! Is there anyone out there who have made this mod on a MSI K8TNeo2 -F ?
Or any simple guide to do a vdimm mod on a MSI K8T Neo2 -F
may i know how to get vdimm reading on multimeter for MSI K8N NE0 2?
thx
Maybe u should try to read the Thread .... ;)
it is the JC11 on the picture measuring point for Vdd
both multimeter probe on the pins or red on the either one & black probe on casing
thx
Red on the green Point Black on Case or any other Ground.
thanks bro...
Direct mod on/off
http://img233.exs.cx/img233/7251/msik8ndirect32im.jpg
http://img233.exs.cx/img233/5386/msik8ndirect3fe.jpg
http://img69.exs.cx/img69/3788/msik8ndirect20fn.jpg
And what I could get from that
http://img203.exs.cx/img203/3251/bh5record3ul.jpg
Definitely, what is the reading VCORE point?? I´m confused. Some pic?
Bye