Also getting one and a 3400+ 1mb cache to acompany it :rocker:
Printable View
Also getting one and a 3400+ 1mb cache to acompany it :rocker:
I'll give it a shot and see what I end up with.Quote:
Originally Posted by bigtoe
Thanks. :idea:
I got it friday, only black screen.. DOA i think.
"Overklokk" got his today, same prob there.
:(
yes my card is DOA..... all fan +hdd+++ starts but no picture..... tested with 3500eb and some Twin mos, 9800pro and x800pro, 2 x 3200+ Claw cpu but nothing happend... just black screen....
@H2OGun:
what the DRAM Drive Strenght does exactly?
and which options are available (grr...still waiting for my board.....i hope, it comes tomorrow....)
I got mine and in my version so far I have found the only BIOS problems to be is if I change any AGP settings int he BIOS it will not POST. Everything else is fine.
I havent had much time to even mess with the board yet...I have been able to get 2.35 so far but that is playing with it for about 10 minutes. Hope to get more.
small update:
mach 1 R507 // no mods
http://www.xs4all.nl/~famchow/A64_3400/DFI/3GHz.JPG
It seems this board is quite vurnable... want to know more about this.
Quote:
Originally Posted by Fosco
So, i'm not alone here.Quote:
Originally Posted by Overklokk
Did you guys also got a blinking poweled like i had?
You guys with DOAs, have you tryed with just one stick of mem in slot1?
OPP
I have the same problem...sometimes.Quote:
Originally Posted by OPPAINTER
My board works OK and boot.
But indeed sometimes it wont boot with 2 mem in bank 1 and 2.
Very strange...
I did, 1 stick of HyperX BH-5 in slot 1, no go, just a blikning powerled. :shrug:Quote:
Originally Posted by OPPAINTER
He says he should have access to a prod board sometime between Today and Friday. He is in transit all over the place, so he prolly wont get to do much w/ it until sometime Friday..... Hopefully some more answers then.
While I get warm boot issues when switching settings, rarely (<1%) do I get really wierd stuff happening.
WRITE DOWN ALL YOU SETTING AS YOU CHANGE THEM!!!! :hehe:
I have had 2 occasions when the DFI UT screen suddenly comes back up after a setting and bios setting are now back to all defaults so if you DON'T write your settings down you may be :bananal:
i just got my 250GB in the mail today, will be settin it up this evening. i cant wait to test this thing out....
Yes....Quote:
Originally Posted by OPPAINTER
Fosco godt the card booting with a 3700+ and Bh5 but it did not boot with 3200+ Claw and OCZ EB
I use a old 3200+ Claw and tryed Muskin level 2 BH5- Twinmos 3200 (samsung chip) and OCZ 3500 EB no boot.
I hawe ordred a 3700+ today and it wil be her on Friday... hope my DFI works then
Any other with this problem?
Man, the Orb seems to have a hard time reading this thing. I made a couple runs, first one's stock,(9x200) then @ 9x245. Especially check out my vid clocks, stock in both runs. :shrug: http://service.futuremark.com/compare?2k3=3106945 then OCed http://service.futuremark.com/compare?2k3=3107674 Obviously, the vid drivers aren't FM approved, but you'd think it could read the board's settings better. :lol:
Well its only PC2100 speed but check the timings ;)
heh, thats just sick.
Got my board running, so far its runnin great with my 2x512mb mushkin level 2 BH-5
my 3200+ C0 1mb and my 9800pro
THE POWER LED will be blinking between cpu is up/running and finished memory testing ...Quote:
Originally Posted by Zeus
If the cpu is not up/running bios code , the power led will not be blinking ...
At least that means the cpu core is running the bios code ...
put a pc speaker to see if their is a continuously beeping sound ...
If the anwser is yes , that's dram issue ...
Try to clear cmos and put dram in slot1 or slot2 or slot3 to see if the system can pass the memory testing sequence ...
im really liking this board. almost beating my watercooled 3200+/9800XT scores on air. and i still havent even done the performance aniso tweak or tightened my ram timings http://service.futuremark.com/compare?2k1=8117896 :)
Nice, you're beating my X800 Pro in SOME tests. ;) :thumbsup: http://service.futuremark.com/compare?2k1=8117930 I'm pretty happy, I broke 25k. :bounce: Hey bigtoe, did it actually boot with those timings? :slobber:Quote:
Originally Posted by Boyne7
Thanx gouda96, and Oskar_Wu, and Jess1313 . :toast: My Mobile 3000+ has been runnin' fine, but this is definitely worth a try. :) I know my 3.3 goes up a ways, never tried to see HOW far yet. :explode: :rotf:
Oscar,Quote:
Originally Posted by OSKAR_WU
I have my systemspeaker hooked up and there is no beep coming from it.
I have cleared Cmos at least 10 times and also took out the battery for half an hour.
I also tried 1 stick in slot 1 and tried 1 stick in slot2, slot 3 gave a continues beep.
Shouldn't be a mem issue as Kakaroto is running the same RAM (HyperX 3200 BH-5 2x256) in the same board w/o issues.
My CPU worked well with this mem in my old mobo.
Any clues?
edit:To clear confusion, i'm talking the powerled of my case that's blinking, not the onboard DRAM powerled or standby powerled.
I know you mean powerled of case , if the onboard DRAM powerled or standby powerled is blinking , your chipset on the board is " burned out " ...Quote:
Originally Posted by Zeus
Ok , my recommendation will be ...
1 . Take off the board , remove any thing including retention kit come with the board
2 . Turn the board to back side and check carefully if there is anything short between all the DIMM/AGP slot pin ...
3 . Put only the MB on an safe platform , remove AC power cord first
4 . Plug the ATX 20 pin and ATX +12V 4 pin power connector
5 . Install the cpu , put the cpu heatsink on it carefully
6 . Install one DIMM in DIMM3
7 . Plug the spreaker or buzzer on the front panel connector
8 . Plug the AC power cord
9 . Boot up the mainboard to see if there is any beep sound
10 . No beep sound or continous long beep sound ? Return it to your reseller and ask for an exchange ASAP ...
11 . 3 short beep sound ? Turn off the power and install the video card , it should be able to boot with display card if there is 3 short beep sound without video card on the MB ...
OSKAR_WU:
This is Probly a Simple Question for you, But..
On the DFI, the Bios chip is 4mb? and the bios is 512k, So What happeneds with the extra 3.5mb?
Kinda curious, i mess with xbox bioses and such, so it came to mind.
Thanks for your time & GREAT work!
But I have gotten 1800+ mb/sec (exact match - memtest) w/ 1 .5G stick of BH5 (2-2-2-7) and one stick of EB 3700 (3-2-2-6) @ 250 FSB (140/358 x 7) or (150/333 x 7.5).
Which would you go with, since neither seems to have much more left in it :shrug:
Quote:
Originally Posted by OSKAR_WU
1.done
2. checked thoroughly, no shortage whatsoever
3 to 9. done
10.with RAM in slot3 continues beep, other 2, no beeps
Contacted my reseller, now waiting for him to get new boards shipped.
Thanks for your help, Oskar Wu. ;)
can the bios savior RD1-PMC4 for 32pin 4Mbit be used on this board ?
Quote:
Originally Posted by eva2000
Yes. ive ordered one allready. Might be cheaper if you buy another Chip (dfi-street.com has a member selling the chips for about 10.00 shipped) you can just hot flash it, then you have a cheap spare.
10.00 bucks for a blank chip
30.00~ bucks for the RD1
Your choice :)
already have 2 spare RD1-PMC4s hehe
Its 4MBIT , and that is 512KB.Quote:
Originally Posted by Dissolved
You should know that, every bios (SST = 4MBIT)
Bleh, i wish i would have known i would of bought one..Quote:
Originally Posted by eva2000
OK im tired as hell (too much sitting on my butt watching memtest loop on my DFI)Quote:
Originally Posted by kakaroto
But doesnt 4mbit / 512kb = 8 Times.. Meaning the bios is 512KB, uses 1/8 of the bios chip.. So what is held on the other 7/8 of the chip?
Edit: This mobo is Fun as heck so far! 260FSB 3-2-0-2-9-11 LDT 3x So far..
mmmm
8Bits=1Byte
ciao
Alessio
Wrong... 4Mbit = 4096Kbit (4x1024) include start and stop bit :)Quote:
Originally Posted by Dissolved
4096 / 8 = 512KB!
Quote:
Originally Posted by kakaroto
4mbit / 512kb = 8 4096 / 8 = 512KB
Same thing?
so when flashing the bios chip with a 512kb bios file it Doesnt Fill the full chip is what im asking.. i think i need sleep, my mind is telling me that you could have 8 different or same 512KB bios(es) on a 4Mbit bios chip..
:sleep:
I Identify with that (snore smiley, followed by zombie smiley)Quote:
Originally Posted by Dissolved
I AM USING THE BSAV MENTIONED HERE, WORKS FINE.
Trying for more BWidth :brick: :bounces:
8 is the factor between bits and bytes mate.Quote:
Originally Posted by Dissolved
Quote:
Originally Posted by Joe T
OK, thats all i needed... NOW i can sleep lmao.. Thanks..
:retarted:
I LIKE THIS BIOS LOOK AT THE MEMORY SPEED FSB (AND ITS PASSING!) :banana4: :p: :slobber: :hehe: :rotf: :ROTF: :banana:
https://home.comcast.net/~mikeehrlich/DFIUT/dfiut.jpg
Oh did I mention there's a slight reporting bug at some of the dividers that show HTT as mem FSB :D
:d ;)
Quote:
Originally Posted by mad mikee
which devider?
OMG, Please stop posting these screenies. :slobber:
I have to wait till my reseller gets new boards in before i get a new one.
Let me be the first to put down some downsides of this board:
-The AGP slot sux, the release tab is changed to some crappy meant-to break-thingie.
-The manual is very basic, not a word on the bios despite it's many complex options.
-The slots are yellow as a :banana: which holds back overclock.
-Can't think of any more, no matter how hard i try. :D
Anyone know if ClockGen works fine on this board?
At what speed is it actualy running?Quote:
Originally Posted by mad mikee
Is that PC3700EB? :slobber:
I like my DFI every day more and more :D
Tryed a fully stable setting @1.7v
http://www.xs4all.nl/~famchow/A64_34...GHz_stable.JPG
Need EB's ram to run 300MHz 1:1 :D
@Zeus: Clockgen works perfect here ... only changing VID/FID is not possible.
Is there a trend of "getting DOA mobos" alÃ:banana: lanparty nf2 or just some rare cases?
the idea of getting a doa mobo doesn't appeal me the least :/
yes, is it your bh5 or your eb in that board?! omg i mso excited, one more week and ill be going A64!!!!!Quote:
Originally Posted by kakaroto
I'd say rare cases, look how many have been sold already. A few bad ones is normal, noone makes em 100% perfect everytime. ;) kakaroto, which chip are you runnin? I'm stuck with a 9x multi on my 3000+. :p: BTW guys, look at the bottom of mad mikee's screenie. :stick: :DQuote:
Originally Posted by Rudzer
Is the Command per clock option in the ram menu the settings for 1T/2T? I think it is, but I'm not sure. Setting to enabled or auto gives me 1T.
I want to get this board past 300 but nothings really helping much, even when using a divider.
right now I'm at 260x10 1:1
1.7vcore
3.1 vdimm
AGP is 1.8v
chipset is 1.9v(i have a 40mm 6000 rpm fan on it blowing down)
ldt is at 3x
cas latency is 3
ras-cas 3
tras 10
trp 3
trc 12
trfc 16
tony mentioned playing with the drive strength? What's a good setting to start out with? right now it's at 2 but I don't see a difference. options are 1-4. so which one's best for stabliity? 1 or 4? Does agp voltage help at all? I've left it alone in the past, but I heard increasing the voltage helps stabilty. Please let me know if you have any recommendations. I'm using ram slots 1 and 3
see my sig for what I'm using.
@transam
Yes, that's the 1/2T command - auto/disabled will give you 1T, enabled is 2T :)
Can't get mine running at 300 from bios either... so far now 270x8 x4HTT works fine..
Even with ClockGen my mem (OCZ PC4200) doesn't want to go higher at this point, regardless whether I relax timings or set 2T command... :(
I have it enabled and during post it says 1T still. are you sure about that? I also tried the drive strength settings. 4 was good. but 1 made the system cold boot and no post. So I think 4 is probably the setting tony was talking about.Quote:
Originally Posted by chickenrun
I really wish I could go past this 300ht barrier so I can get some more from this EB 3700. I seem to do 270 at 3-3-2-10 1T ok but anything over is no good. even at 3-3-3-10 there was no difference. 260x10 at 1:1 for now.
:( notice in the cpuz screenie, I messed up in the bios and had my TRAS at 2 LOL. I fixed it since. what settings are best for TRC and TRFC? right now it's trc 12 and trfc 16.
I tried 269*9.5 at 1:1 and that seems to work pretty well.
Here it is a challenge for the enthusiasts of the DFI Lanparty UT NF3250GB (uff..what a big name the DFI marketing created):
1st– Drop the multiplier for 5X or less;
2nd -Put the memory at 150,
3rd - Use 2 sticks of BH-5 RAM at at 2-5-2-2
4rd - Rise the HTT for 350 or more
And see if it runs SuperPI (I’m not asking for a good score)…
With my "old" Gigabyte K8N (Nforce 150), I can run SuperPI with FSB (HTT) at 380 (I pick only this screen capture, because I was chasing the A64 3400+ record).
http://home.kqnet.pt/wo034892/28SecSuperPI.jpg
Show me this board can really beat my good old unexpensive KN8Pro ..
Please convince me that the DFI DFI Lanparty UT NF3250GB it is a little more than one (a very good one, I must admit) marketing scheme..
Please don’t came with the BS.. arguing that I only obtained this high HTT because I use the Best Dual Cascade of the Planet (Ricky’s Dual Cascade, of course) - if you put down the multiplier for 5x or less, you are at lower CPU speed than stock..right..
Let’s wait for the results..
:toast:
That works on mine, changes it to 2t, but doesn't seem to affect anything. On a similar note, I tried changing my CAS from 2 to 3, and it wouldn't post. I had to clear CMOS to boot up again. :( I really thought that would make this BH-5 fly. Maybe if we had an option for CAS 2.5? I'm still using the stock BIOS, so I dunno about the newer ones.Quote:
Originally Posted by trans am
so how does this board compare to your chaintech?Quote:
Originally Posted by trans am
yay 23k with my 9800pro :) http://service.futuremark.com/compare?2k1=8120308
a slight bump in vga core and ram timings did it. tras "0" lol now i need to get an OCZ ddr booster
You can't just mod your pus's 3.3v rail? That would be cheaper, and take less time then buying an ocz ddr booster.Quote:
Originally Posted by Boyne7
@Transam
Well, it works this way for my Ram ?!?!
With the half multis my mem score in Sandra dropped by around 300 points as expected :( The 2T command also really slows down the mem...
Playing around with the settings gave me a bit of increase, but nothing really worth mentioning (50 points or so in Sandra)...
Did not have time to check out the drive strength settings though, will hv to see what 4 allows for
@pedro
I think the REAL challenge is to get it booted with those settings from bios ! ClockGen seems to hv problems with this board when it comes to lowering the multis :(
1. (1)CommandPerClock ENabled = 1t, disabled = 2T :rolleyes:
2. Pi thingie - Perhaps this weekend.
I am tried both 330+ (7.5x, 150 Div) and 350+ (7x, 140 Div) w/ FSB at about 245 and memtest does fine.
May have to lower the mult when I run windows, but vcore is only at 1.525-1.5 for now.
I'm not convinced that this board is all that much better than the vnf-250 yet (was running that at 8x300 w/fsb of 250, less BW. Even though you couldn't adjust much stuff, then defaults were pretty good (for all the stuff that you can fiddle w/ in A64 Tweaker).
Fiddling w/ this board has gotten me educated enough that I migh even get some performance out of my gigajunked k8ns-pro board now that I have an idea what to tweak and knowing that that board does have alot of the same tweaks :D Gotta find time to revisit that later.
Will try this out ASICFIN (as soon as I can fit it in).
I think I was running 140 divider. The act. mem FSB was about 245-250 and I hadn't fiddled w/ all the stuff setting wise. I can give settings (when I have time to revisit them, life is nuts as usual) for equal bandwidth at a given memFSB for both bh5(2226 or 2227, I fergit) or EB3700(3226) (2x.5G). (There are some slight setting differences, but nothing major)Quote:
Originally Posted by ocmyface
I can never seem to get to 250 w/ what I would consider acceptible BW stable, and raising FSB didn't work. I have been at a point when the max BW at 250 was 1812MB/sec in memtest.
BTW, should I concentrate of the bh5 which seems to go a couple of FSB higher and w/ the faster Latencies, or should I fight w/ the EB 3700 (one stick is for sure 250FSB/1812, the other maxes hard at about 243/1730MB, so of course the lower one is the limit) Of course I found out from Bigtoe that they don't have anymore like my good stick if I wanted to try for a replacement (my curse w/ memory)
HTT as been up to 360 (140 div). Forget what I went to at 133, (BW went down) and 120/100 div. don't POST.:mad:
Haven't been over 400 yet, maybe trie just for the heck of it this weekend if I have time....
Its kingston BH5 256MBQuote:
Originally Posted by ocmyface
Yeah with what HTT multiplier?Quote:
Originally Posted by Pedro Rocha
The half multi's made your scores drop? in which test? bandwidth? cpu? My friend klisp has this board too and he said that when he used dimm 2, 3 the board ran at 2t and using 1 and 3 or 1 and 2 the board ran at 1t. Weird huh? Someone mentioned a beta bios that came out on 9/14 (not the one that fixed the mobile issue that oskar made,) but it's a different one that allows 3.4vdimm. but you need to raise the rail on you psu. I have a powerstream with adjust. rails. could I use the bios in question with the adjustable rails? Does anyone have a link to it?Quote:
Originally Posted by chickenrun
(BOSHI)
so how does this board compare to your chaintech?
It''s better and the temps actually work. much better support thanks to oskar wu. and the voltage options alone make it worth the extra money. But my total cpu clock hasn't really changed. But then again I can get much more from my EB 3700 with the higher vdimm. My ram couldn't go past 250mhz on the vnf3-250 and with the dfi with 3.1v I can hit 270mhz! It huge difference in bandwidth tests.
BH-5 doesn't work with CAS3.Quote:
Originally Posted by spaceman
Anybody know what coolers are compatible with the board? or if the Zalmans are compatible?
The memory I have now seems to not be fully compatiable with the DFI...
Every once in awhile I get memory dump errors. I am running Infineon 2 512 sticks.
And for some reason when I changed BIOS version I can't load @ 230 FSB anymore. Does anyone have a link to a updated BIOS? Maybe I can fix this memory issue until I can afford some new RAM.
Upped my fortron 3.3 line to 3.4 and was okay. Could prolly up it more but not worth it to me. Aiming for 3.1/3.2. My BH-5 seems to be better for BW than my EB (can reach higher FSB at settings for equivalent BW.)
When testing FSB isn't everything, BW is what counts,
(except in regards to CPU speed vs BW). My memory can go for higher FSB w/ changing the upteen various settings but the bandwidth limit seems to be pretty much constant for a given stick of memory. Talk about qualitative / intuitive multi-variable analysis! :confused:
As for cooling zalman, hyper6, and others fit fine, search / google is your friend.....
I have Fortron Source 530-Watt and I also need to open the voltages up so I can achieve higher overclocks. When I take my vacation I will have lots more time to play with this. But until then I will sit here at a very stable 2.2GHz. Good enough to play a game or two when I want to. I also took one of my 512 sticks out to see if I still get the memory dump errors. *crosses fingers*
*edit* Still not compatiable for some strange reason...I have been running this for days up until now and I changed BIOS version and it is still doing this...I even tried going back to the shipped BIOS and still the same thing. Someone please help me out...
The Zalman 7000 work..that is what I am running and it stays pretty cool. my CPU runs about 35 to 37 idle.Quote:
Originally Posted by Godmyster
Bios Link
I don't see why you wouldn't use the bios with the mobile fix. It is just the beta bios, but without the boot bug for mobiles, and still has vdim mod.
Alright I'll give that a try. To add to it... I ram MemTest and I recieve no errors with the RAM @ 220 @ 2.3-3-3-10 @ v2.9
*EDIT*
Ok I got the BIOS Update for that...not sure if it has fixed my problem as of yet...But I can't load windows clocked at anything higher than 2.2 anymore and I still can't figure out why...I have even tried loading defaults and just clocking it straight at 2.3 and it wont. Before I started all the BIOS chaning to fix other problems I was running 2.3 just fine as normal usage and trying to hit 2.4+ for benchmarking. Does anyone have any answers to why this could be..?
*EDIT Again* lol
Ok so I am messing around with it alittle more now and I am getting alitle better and figuring out what works with this board. I am still very new to overclocking but I am learning.
ugp witch Zalman 7000 do u have? and what other Zalman 7000 models give? :)
I have the Zalman CNPS7000A-CuQuote:
Originally Posted by Godmyster
Right now I am at 275x8.0 and my CPU is idling at 33-35C
To me that isn't bad.
And to add a question to others...what are safe FSB speeds on Air cooling like I have? I don't want to go to far and damage my system. I don't have the money to replace anything right now
I had mine 325x8 but that was with a thermalright 948u and a tornado. High voltage. didnt run it that long because i though my chip would die. no bad for 600mhz overclock on air.
I'm using the Swiftech MCX64-V on mine. I just used the screws from the bracket, and the stock yellow backplate, without Swiftech's spring tensioners. Works great, as long as your halfways careful about torqueing it down. :cool: BTW, I grabbed that BIOS right away yesterday, but since my Mobile 3000+ (1.8 stock) already runs fine @ 2.4 GHz., I'm just a tad leery of tryin' it, lol.Quote:
Originally Posted by Godmyster
How high was the voltage?Quote:
Originally Posted by shafty
FYI OnlyQuote:
Originally Posted by Pedro Rocha
http://oskarwu.myweb.hinet.net/LPUTNF3250GB/3852222.jpg
Fvcking Owned!
That didn't take long...
I don't understand how the dfi board is a marketing scheme? It is a piece of exceptional hardware, and I don't see how that has anything to do with a marketing scheme.
im slightly confused, so by upping the voltage of my 3.3 line it automatically increases the voltage of my ram? because i have the OCZ powerstream 520 and when i up the voltage on it the DFI smartguardian thing doesnt show that the ram is increasing whatsoever.
Upping ATX +3.3V will not increase your VDIMM automatically unless you set higher VDIMM in bios ...Quote:
Originally Posted by Boyne7
Gives you ability to choose higher vdimm options in the bios and THAT will get you the VDIMM upto some value < what your line is set to (we haven't even talked about measuring where w/ dmm) :cool:
PS: Just noticed who did the screenies above.
WAY TO GO OSKAR!!! :toast: , shows whos paying attention. :hehe:
OSKAR WU: Is that with HTT X4?? :slobber:
whoa... not 150Mhz but 275Mhz... :slobber: i just wonder what sticks are those and how much vdimm it takes for them to get there...Quote:
Originally Posted by OSKAR_WU
Quote:
Originally Posted by bachus_anonym
notice his system monitor screenie says DRAM 3.56. considering how fast his ram is overclocked and that it's at 2-2-2-5, It's definitely 2x256 sticks of BH-5.
but... oskar wu works for dfi, right
he could pick a good board, lets see someone who got theirs from gameve do this, just for verification
He probably got a random board like everyone else.
My 3.3v line is already at 3.64 or so, and no more options have appeared in the bios, the highest is still only 3.1v which is what im usingQuote:
Gives you ability to choose higher vdimm options in the bios and THAT will get you the VDIMM upto some value < what your line is set to (we haven't even talked about measuring where w/ dmm)
It's impossible for NF3 chipset ...Quote:
Originally Posted by kakaroto
Do you have the modded bios that allows for vdim>3.1v? :stick:Quote:
Originally Posted by Boyne7
What I don't get - I run the mem with 270 1:1 (4x HTT manually in bios) BUT using the HTT speed analyzer it shows me 4x200 ?!?!?!? I know its made for the Via chipset - is there a bug using it with the NF3 ?
He say put DDR in 150 option and cpu multiplier under 5X ... Based on the two setting , cpu will use divider 7 for DRAM frequency divider ...Quote:
Originally Posted by bachus_anonym
A-DATA BH5 256MB X 2 , VDIMM = 3.6V
That's why I say FYI only ...Quote:
Originally Posted by blinky
Due to K8 has integrated memory controller , OC limitation of same designed MB will mostly be decided by CPU itself ...
:D I think keverybody who did a bit of research on all of this A64 stuff should know this by now anyway and should not complain about his cpu not doing as well as his friend's one...:rolleyes: :cool:Quote:
Originally Posted by OSKAR_WU
HTT speed analyzer only analysis the ratio , not the FSB ...Quote:
Originally Posted by chickenrun
good work oskar. I knew it was bh5! Was it your idea to do the vcore like it is? why did you choose to do it this way instead of just having all the values ready to go? I think it's cool but it's also annoying because every time I want to play with the vcore I need to use a calculator. We americans aren't the best at math, lol! Is there any difference when using 4x ht link or is 3x the best and most stable for overclocking? Currently I'm using 3x and it seems like I can overclock higher.Quote:
Originally Posted by OSKAR_WU
Probably this as been answered like a lot of times, but how do i calculate the mem speed with the 180 divider? or is there any program that shows the speed?
Thanks!
What LDT were you using OSKAR_WU?
wow.... sry, i definately didn't know there was a modified bios. anyone happen to have the link for it?
I posted a link to them twice I think. Check a few of my posts back.
use the modded BIOS, there are 3.2V~4.0V optionsQuote:
Originally Posted by Boyne7
http://www.ocforums.com/showthread.php?t=328318