XS Yonah T2600ES competition !!!

Printable View

Show 100 post(s) from this thread on one page

04-21-2006, 07:22 AM
railer

DAmn Hipro that suks. I was looking forward you playing with Yonah setup. Then mayby Merom since we get bios to support this board. Anyway its kind of funny that most experienced vmoder got screwd like that. You should of check for mods yourself, since these boards are very new, I'm sure you would find some good Vmods. Well sell your Dothan sys and get onother board;)
04-21-2006, 07:29 AM
hicookie

Quote:

Originally Posted by hipro5

He mustn't have done THIS mod coz if you see at his photos with the mods, the other mods have cables soldered on the mobo BUT this one HASN'T any cables....JUST spots showing shi(f)t as I show......:(

sorry, hipro, i have not done the nb mod, is not the nb vmod? :confused:
04-21-2006, 07:38 AM
irev210

is there any way to set up a RAID using the intel southbridge chip... i've been looking and dont see a way to do. Just the ITE raid, which obviously wont support my 4 sata drives.
04-21-2006, 07:47 AM
hipro5

Quote:

Originally Posted by hicookie

sorry, hipro, i have not done the nb mod, is not the nb vmod? :confused:

No hicookie, it's the Vio(Vtt if you wish) of the Northbridge.......:(
04-21-2006, 07:50 AM
hipro5

Quote:

Originally Posted by railer

DAmn Hipro that suks. I was looking forward you playing with Yonah setup. Then mayby Merom since we get bios to support this board. Anyway its kind of funny that most experienced vmoder got screwd like that. You should of check for mods yourself, since these boards are very new, I'm sure you would find some good Vmods. Well sell your Dothan sys and get onother board;)

I was searching for other possible mods and I thought that if this one was already done and works, what's the reason of doing it myshelf too!......I did it and BANG......:(
04-21-2006, 07:52 AM
Harshal

Real BAD news... Hipro, Hope you get one more ASAP. As peepz are waiting to go crazzy after the Guru show them the way :) I think I am going to sit tight on this as I am not too good with Mods.
04-21-2006, 08:12 AM
s7e9h3n

Quote:

Originally Posted by hipro5

A L A R M .....

http://www.thelab.gr/images/Hipro5/T...ULT_NB_Mod.jpg

DON'T do the hicookie's VCore NB Mod coz IT'S NOT the NB Core....

It's the Vio of the i975 chipset and you'll measure NOTHING on the spot he pointed out for measuring.....You'll measure the REAL Vchip voltage BUT NOT coming from the regulator he's pointed out.....

WRONG REGULATOR........I just BLOW UP my AOpen mobo (Northbridge chip) by trimming the trimmer and NOT showing anything changing on the spot he has pointed coz there's NOTHING to do with this.......:( :(

It costed me 400$ this "Mod".......I was so anxious to mod my mobo that I thought not to search for Vchip Mod coz there was already be done by someone else, so I did this mod......BAD think......:(

QUESTION: @ hicookie....DID you do this mod on your mobo?.....DID you see changing by trimming the trimmer onto the measuring spot you are showing in your photo?......OR you just presume that this might be the VChip mod?.....:mad:

A L A R M .....

THIS is the thread aboud mods.......http://www.xtremesystems.org/forums/...ad.php?t=95411

Thanks hicookie you made my day...... :(

.

Ouch...sorry to hear that my friend! No wonder when I adjusted it, I didn't measure any change in chipset voltage....
04-21-2006, 08:36 AM
Gamer

ouch, bad luck.

how about your test Waus ?
04-21-2006, 08:42 AM
Chri$ch

anyone an idea how can i go over 268FSB?

Bios Settings:

VCore [1.55v]
VDimm [AUTO]
VNB [AUTO - Max]
PCIe V [AUTO]
SpreadS. [Disable]
FSB [250Mhz]
PCIe [100Mhz]
PM [Normal]
04-21-2006, 10:01 AM
ibby

Quote:

Originally Posted by kiwi

Anyone got past 256FSB with step 4 cpu?

Step 4 seems to be much weaker

I am stuck at 201 :( :mad:
04-21-2006, 10:16 AM
guess2098

Quote:

Originally Posted by hipro5

I think that this VChip mod that hicookie has posted, it is done by NO ONE else except me off caurse........... :mad:

I have found about 6 Mods on this mobo so far.........Not more coz after hicookie's "Vchip mod", mobo went down.........:(

I had a wall at 215MHz with a stepping 4 T2400 one........

As for the "cold boot start" just place the Jumper that Waus-mod had posted a question about, in the middle (pins 2 an 3).........This jumper will help the cold boot problem coz when you firsty power up the AOpen, it feeds the CPU with only 1.00Volt and during post it feeds it with the VCore you have chosen via Bios........By placing the jumpers at 2,3 pins, when power up mobo, feeds the CPU with 1.4Volts and afterwords with the VCore you have selected via Bios.......;)

i did the something
no problem
but using 100K not 10k!
i think that is error!

edit i saw it wrong, i thought it is vcore
04-21-2006, 10:20 AM
misteroadster

Do you have some memory bandwith results here ?, it seems there is a problem there, some members on OCM reports 5xxx Mb/s with everest and sandra , me think it's a single channel bandwith. :confused:
04-21-2006, 10:43 AM
albertwesker

Quote:

Originally Posted by misteroadster

Do you have some memory bandwith results here ?, it seems there is a problem there, some members on OCM reports 5xxx Mb/s with everest and sandra , me think it's a single channel bandwith. :confused:

~6300 with centon FatD9 @ 476 MHz 4-4-3-8
04-21-2006, 10:59 AM
misteroadster

really bad for the frequency :/ same bandwith than any A64 200 FSB 5/2/2/2, it's understandable that dual Pi hurts performance with that poor bandwith.

What a P4 give with those settings ? 10000-11000 ??? i'm a INTEL noobish sorry :D
04-21-2006, 11:06 AM
before

Quote:

Originally Posted by njkid32

Yes Stephen still has the yonah and mobo but was having serious coldbug problems last night with his auto-cascade:(

Bloody hell! :eek: Really bad news...
04-21-2006, 11:07 AM
misteroadster

m/b coldbug probably ;)
04-21-2006, 11:18 AM
before

I hope so dude... :D

BTW not sure about that, but increasing the voltage of the chipset of my DFI nF4 Ult-D gave (or at least made me think about that) me a little more stability while the CPU temp was @~-47°C with my FX-55 0516WPMW @255HTT... I might be wrong but AMD cold-bug has something to do with motherboard as well.
04-21-2006, 11:50 AM
Gamer

I get high 32m scores, how can I improve this ?
04-21-2006, 12:20 PM
Rol-Co

Quote:

Originally Posted by Gamer

I get high 32m scores, how can I improve this ?

Lower timings gamer, the 1m can be better too......much better.:stick:
04-21-2006, 12:21 PM
albertwesker

Quote:

Originally Posted by before

Bloody hell! :eek: Really bad news...

he has to set the yellow jumper in the middle, then the coldbug is gone.
04-21-2006, 12:23 PM
stummerwinter

Quote:

Originally Posted by hipro5

No other board........ :(

YES this jumper I mean........;)

Hey, man, that´s goof news...:clap:

Sorry to hear, that your board is dead. Maybe that´s the reason, why Bogi killed his board too...:rolleyes:
04-21-2006, 02:33 PM
Rol-Co

Tested Waus-mod cpu on the aopen board of mine.

max fsb i reach't here with zalman 7000cu on it

score
04-21-2006, 03:47 PM
NapalmV5

Quote:

Originally Posted by Rol-Co

Tested Waus-mod cpu on the aopen board of mine.

max fsb i reach't here with zalman 7000cu on it

http://rol-co.nl/images/239.jpg

LOL... many of us are getting the same resuts... funny!

guys, is there a vcore pin mod anywere?
04-21-2006, 04:58 PM
Rol-Co

Quote:

Originally Posted by NapalmV5

LOL... many of us are getting the same resuts... funny!

guys, is there a vcore pin mod anywere?

becouse its cpu related :(

i can reach 243,5 fsb with mine till now, with better cooling it's gona be higher i think.:D
04-21-2006, 11:48 PM
kiwi

Somehow I don't wanna agree that it is 100% cpu related. We have only one board to test it on. And remember Dothans 7x0 hit at least 250-260+ easily.

Show 100 post(s) from this thread on one page